ページ1に含まれる内容の要旨
SyncMaster 172B/172T
ページ2に含まれる内容の要旨
User’s Manual Index Main Page On-Screen Display Safety Instructions Troubleshooting Notational Check List Power Q & A Installation Self-Test Feature Check Cleaning Other Introduction Specifications Unpacking General Specifications Front PowerSaver Rear Preset Display Modes Setup Information Connecting Your Monitor Service Installing the Monitor Driver Terms — Automatic Regulatory — Manual Natural Color For Better Display Authority
ページ3に含まれる内容の要旨
User’s Manual Safety Instructions Notational Warning/Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Notation Conventions Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock
ページ4に含まれる内容の要旨
User’s Manual Safety Instructions Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire. Use only a properly grounded plug and recepticle. An improper ground may cause electric shock or equipment damage Do not e
ページ5に含まれる内容の要旨
User’s Manual Safety Instructions Power Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. Failure to do so may cause an electric shock or fire. Do not connect too many extension cords or plugs to an outlet. This may cause a fire.
ページ6に含まれる内容の要旨
User’s Manual Safety Instructions Installation Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Put your monitor in a location with low humidity and a minimum of dust. An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. This may cause damage to the product or human body. Place the monitor on a flat and stable surface. The monitor can cause injury by falling. Set down the monito
ページ7に含まれる内容の要旨
User’s Manual Safety Instructions Installation Do not place the monitor face down. The TFT-LCD surface may be damaged.
ページ8に含まれる内容の要旨
User’s Manual Safety Instructions Clean When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric. Do not spray detergent directly on the monitor. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. A dirty connector can cause an electric shock or fire Do not set a glass of water, chemicals or any small metal objects on the monitor.
ページ9に含まれる内容の要旨
User’s Manual Safety Instructions Other Do not remove cover(or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel. If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized deal- er or service. This may cause an electric shock or a fire. Do not place any heavy objects on the monitor. This
ページ10に含まれる内容の要旨
User’s Manual Safety Instructions Other Do not try to move the monitor by pulling on the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable. Never insert anything metallic into the monitor openings. This may cause an electric shock, fire or injury.
ページ11に含まれる内容の要旨
User’s Manual Introduction (Sync Master 172B) Unpacking Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Unpacking D-Sub Cable Quick Setup Guide Power Cord Warranty Card Monitor (Not available in all locations) User's Guide and Driver Installation CD DC-Adapter VESA Mounting Bracket For Multimedia model (Option) Multimedia Speaker Stand Sound Cables
ページ12に含まれる内容の要旨
User’s Manual Introduction (SyncMaster 172T) Unpacking Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Unpacking D-Sub Cable Quick Setup Guide DVI Cable (Option) Warranty Card (Not available in all locations) Monitor Power Cord User's Guide and Driver Installation CD DC-Adapter VESA Mounting Bracket SOG cable KIT(Option) For Multimedia model (Option) Multimedia Speaker Stand Sound Cables
ページ13に含まれる内容の要旨
User’s Manual Introduction (SyncMaster 172B) Front 1. Auto button Use this button to auto adjustment direct access. 2. Exit button Use this button to Exit the active menu or the OSD. 3. Adjust buttons These buttons allow you to highlight and adjust items in the menu. 4. Menu button Use this button to open the OSD and activate a highlighted menu item. 5. Power button Use this button to turn the monitor on and off. 6. Power indicator This light glows green during normal operation, and blinks gree
ページ14に含まれる内容の要旨
User’s Manual Introduction (Sync Master 172T) Front 1. Auto button Use this button to auto adjustment direct access. 2. Exit button Use this button to Exit the active menu or the OSD. When push the 'Source' button, then Selects the Video signal while the OSD Source button is off. (When the Source button is pressed to change the input mode, a message appears in the center of the screen displaying the current mode -- analog or digital input signal.) Note:If you select the Digital mode, you mu
ページ15に含まれる内容の要旨
User’s Manual Introduction (Sync Master 172B) Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the 15-pin, D-sub connector on the back of 2. Signal port your monitor. See Connecting Your Monitor for further information regarding cable connections. Note:
ページ16に含まれる内容の要旨
User’s Manual Introduction (Sync Master 172T) Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port Connect the power cord for your monitor to the power port on the back of the monitor. 2. Signal port Connect the touchscreen cable to an available serial communication (COM) port on the back of your computer. Connect the DVI Cable to the DVI Port on the back of your Monitor. 3. DVI port Note: See Connecting Your Monitor for further information re
ページ17に含まれる内容の要旨
User’s Manual Setup (SyncMaster 172B) Connecting Your Monitor Setup-General 1. Connect the DC Adapter for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 3. Connect the monitor to the Macintosh computer using the D-SUB connection cable. 4. In the case of an old model Macintosh, you need to connect the monitor using a special Mac adaptor.
ページ18に含まれる内容の要旨
User’s Manual Setup (SyncMaster 172T) Connecting Your Monitor Setup-General 1. Connect the DC Adapter for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 3. Connect the DVI Cable to the DVI Port on the back of your Monitor. 4. Connect the monitor to the Macintosh computer using the D-SUB connection cable. 5. In the case of an old model Mac
ページ19に含まれる内容の要旨
User’s Manual Setup Connecting Your Monitor Setup-For Multimedia model 1. PC sound connection terminal (Input) 2. Headphone connection terminal (Output) 3. Volume 4. To listen in privacy,connect headphones here. 5. Connect a sound cable from the input source (sound card,computer,CD-ROM drive).
ページ20に含まれる内容の要旨
User’s Manual Setup Att aching a base (Option) Attaching a base NOTE: This monitor accepts a 100mm x 100mm VESA-compliant mounting interface pad. Squeeze the folded monitor stand into the VESA mounting bracket. Then fasten it using the four supplied nuts with the monitor, mounting pad and VESA mounting bracket aligned. 1. VESA Mounting Brkt 2. Mounting interface pad
