ページ1に含まれる内容の要旨
English8188
TABLE OF CONTENTS
SAFETY INSTRUCTIONS ................................................................. 2
INTRODUCTION ............................................................................ 4
Package Contents .................................................................... 4
Installing or Removing the Tilt/Swivel Base........................... 5
Feature Highlights ................................................................... 5
Maximum Compatibility .................
ページ2に含まれる内容の要旨
SAFETY INSTRUCTIONS 1. Please read carefully all of these instructions below and keep the manual for later use. 2. Please install the swivel base below this product before it comes into use. 3. The voltage ratings and the rated frequency are on the overlay centered at rear side of this product. Do not connect with any source of other voltage or frequency and please follow all warnings and instructions marked on the product. 4. Unplug this product from the wall outlet before cleaning and use a d
ページ3に含まれる内容の要旨
English8388 SAFETY INSTRUCTIONS Usually a suitable power cord is provided by the manufacturer, while this product is sold. However, this product is sometimes, resold or transported to another area of different power system and safety requirements, please pay attention to the selection of a suitable power cord. The plug on the power cord is intended to serve as the disconnect device, the scoket-outlet shall be installed near the equipment and shall be easily accessible. 9. Do not allow anything t
ページ4に含まれる内容の要旨
USER'S MANUAL BENUTZERHANDBUCH Manuel de l'utlisateur PR711/PR711T INTRODUCTION Introduction The monitor is a multiple frequency high-resolution color monitor for IBM compatible PC's or Macintosh and workstation systems. The monitor is equipped with microprocessor based intelligence and multiple frequency scanning capability, allowing it to provide maximum compatibility for various system platforms. The monitor uses the latest screen technology including a 0.25mm Aperture Grille CRT to display c
ページ5に含まれる内容の要旨
English8588 INTRODUCTION Installing or Removing the Tilt/Swivel Base 1.Turn off the system and all attached peripherals. 2.Carefully set the monitor upside down. Remove the Tilt/Swivel Base: 1.Squeeze and hold the latches. 2.Pull the tilt/swivel base to the rear of the monitor and lift to remove the base. Installing the Tilt/Swivel Base: 1.Align the base with the slots on the bot- Install Remove tom of the monitor and insert the tilt/ swivel base into the slots. 2.Push the tilt/swivel base firml
ページ6に含まれる内容の要旨
INTRODUCTION Ergonomics Concerned Electric and magnetic field emissions are kept low to meet the Swedish MPR II and TCO standard. Front user controls allow easy access and comfort to adjust the screen image to your personal preferences. Horizontal and vertical full-scan capabilities allow you to use the entire screen area in most resolutions. A tilt/swivel base for horizontal and vertical adjustments always provides the optimum viewing angle. Instant Power Saving Solution The monitor i
ページ7に含まれる内容の要旨
English8788 INTRODUCTION Recommended Use of the Monitor When setting up and using the monitor, pay special attention to the follow- ing for optimum performance: Do not use your monitor against a bright background or where sunlight or other light sources will shine directly on the screen. The monitor should be placed just below eye level (10°~15°) for optimum viewing. Set the monitor's brightness to match the ambient room light. For optimum focus, the contrast control should not be set to
ページ8に含まれる内容の要旨
CONTROLS AND ADJUSTMENTS Controls and Adjustments Once you have installed the monitor for your system, please read the instructions of this section which give you some guidelines on how to use the monitor more efficiently. It leads you through the various function of the user controls and explains how to adjust the monitor to your personal preference. Front User Controls BNC/D15 ▲ ▼ – + 8 7 6 5 4 3 2 1 1. Power Switch To turn the monitor on or off. 2. Power LED Indicator As long as the monitor
ページ9に含まれる内容の要旨
English8988 CONTROLS AND ADJUSTMENTS "Picture" Menu A.Position: a. Press the "+" or ""key to reposition the display to Picture Position Size the right or left. Pincushion Geometry b. Press the "▲ " key to move the entire picture upwards Rotation Others and "▼ " to move it downwards. B. Size: a. Press the "+" or "" key to enlarge or reduce the Picture Position Size horizontal width. Pincushion Geometry b. Press the "▲ " key to enlarge the vertical size or "▼ " Rotation Others to reduce it. C. P
ページ10に含まれる内容の要旨
CONTROLS AND ADJUSTMENTS "Status" Menu A. Mode: To display timing information for the resolution, Status Mode 1280 x1024 Off time frequency and polarity of the current mode. Power save H: 63.8 KHz Recall V: 59.8 Hz Language H. SYNC: + Location V. SYNC: + B. Off time: Press the "+" or "" key to specify an Off time between Status Status M Mode ode OSD OFF OSD OFF 5 and 255 seconds. O Off tim ff time e After After Pow Power er s sa ave ve R Re ecal call l 58 58 SEC SEC La Langua nguage ge
ページ11に含まれる内容の要旨
English81188 CONTROLS AND ADJUSTMENTS "Color" Menu a. By pressing the "Color" key you can select between Color Mode 1 62 Mode 2 mode 1, 2, 3 or 4 to store your user defined color Mode 3 68 Mode 4 settings. °K 9300 62 b. Press the "▼ " or "▲ " key to select the R/G/B gain, then press the "+" key to increase or press the "" key Mode 1 to decrease the respective color intensity. Color Mode 1 52 Mode 2 Mode 3 51 Mode 4 7500°K 61 Mode 2 Color Mode 1 50 Mode 2 Mode 3 50 Mode 4 6500°K 50 Mode 3 Col
ページ12に含まれる内容の要旨
CONTROLS AND ADJUSTMENTS Energy Declaration This monitor is equipped with a function for saving energy which supports the VESA Display Power Management Signaling (DPMS) standard. This means that the monitor must be connected to a computer which also supports the VESA DPMS standard to fulfill the requirements of the NUTEK specification 803299/94/96. The time settings for switching to a power saving mode are adjusted from the system unit by software. From the first indication of inac- tivity to po
ページ13に含まれる内容の要旨
English81388 TECHNICAL INFORMATION 13 ♦♦♦ Note:This monitor is equipped with a micro-processor which allows the Preset Timing Chart user to set his own preferred mode(s) beyond those standard mode listed below. HORIZONTAL VERTICAL VESA VESA MAC VESA VESA VESA 640x480 800x600 1024x768 VGA 640x480 832x624 800x600 1152x864 1024x768 1280x1024 1280x1024 Display Format at 120 Hz at 120 Hz at 100Hz at 85 Hz at 75 Hz at 85 Hz at 75 Hz at 85 Hz at 75 Hz at 85 Hz Hotizontal Dots 640 720 640 640 832 800 80
ページ14に含まれる内容の要旨
TROUBLESHOOTING Troubleshooting Before calling an authorized service center, please check that the items below are properly connected or set. In case of using a non-standard signal, please check the pin assignments and the signal timing of your adapter with the specifications outlined in sections "Pin Assignment Table" and "Preset Timing Chart" in chapter 4. Problem Items to check No picture Power Switch should be in the ON position and the power cord should be properly connected. Check the
