ページ1に含まれる内容の要旨
HP TFT7600 Rackmount Keyboard and Monitor
User Guide
Part Number 365378-002
August 2007 (Second Edition)
ページ2に含まれる内容の要旨
© Copyright 2005, 2007 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
ページ3に含まれる内容の要旨
Contents Introduction.................................................................................................................................. 5 Introduction .............................................................................................................................................. 5 TFT7600 RKM features............................................................................................................................... 5 Components .....................
ページ4に含まれる内容の要旨
European Union regulatory notice ............................................................................................................. 24 Japanese notice ...................................................................................................................................... 25 BSMI notice............................................................................................................................................ 25 Korean notice ..........................
ページ5に含まれる内容の要旨
Introduction Introduction The HP TFT7600 RKM is a rack-mountable 1U integrated flat-panel monitor and keyboard with touchpad. NOTE: 1U = 1.75 inches or 44.45 cm The TFT7600 RKM is mounted on rails with space available to add a 1U KVM switch box behind the unit. The TFT7600 RKM can be used with all HP 5000 and 10000 Series racks. The TFT7600 RKM uses a 43.18-cm (17-in) color-active matrix TFT LCD. TFT7600 RKM features The following table identifies the TFT7600 RKM features:
ページ6に含まれる内容の要旨
Feature Description OSD Available in seven languages: • English • French • German • Italian • Japanese • Simple Chinese • Spanish Keyboard with Three button touchpad with scroll bar touchpad Power supply 12v DC/30 Watt Scroll keys Four scroll keys (inverted T) Components Reference number Component Function 1 Display release latch Pushes down to unlatch the display assembly 2 Blue LED Turns on when the display is closed Helps identify the HP TFT7600 in a rack 3
ページ7に含まれる内容の要旨
Reference number Component Function 5 Scroll lock LED 6 Cap lock LED 7 Number lock LED 8 Touchpad 9 Left pick button 10 Middle pick button 11 Right pick button 12 Scroll bar 13 USB pass thru Pass thru to the rear USB port (callout 1 in the following figure) Rear components Reference number Component Function 1 USB pass thru Connects to a KVM switch virtual media port 2 USB Keyboard/Mouse connector 3 PS2 Keyboard connector 4 PS2 Mouse connector 5 VGA i
ページ8に含まれる内容の要旨
Installation Installing the TFT7600 RKM The following section covers the installation and setup procedure for installing the TFT7600 RKM. Kit contents The kit contains: • TFT7600 RKM (1) • M6 screws (4) • 6-32 screws (5) • HP Adjustable Toolless Rails (2) • Cable management arm, power adapter with brace rail (1) • Lock plates (2) • USB cables (2) • PS2 cables (2) • Video cable • Power cords (2) • USB cable labels • Documentation This kit contains extra hardware for your conv
ページ9に含まれる内容の要旨
2. Extend the inner slides until they lock into place. 3. Align the unit with the extended inner slides, inserting the unit into the rack. Installation 9
ページ10に含まれる内容の要旨
4. Slide the brace rail assembly in between the HP 1U Adjustable Toolless Rails from the rear of the rack. 5. Align the screw holes on the brace rail with the screw holes on the HP 1U Adjustable Toolless Rails. 6. Secure the brace rail to the HP 1U Adjustable Toolless Rails with two 6-32 screws. Installation 10
ページ11に含まれる内容の要旨
7. Remove the two shipping screws from the rear of the HP TFT7600 and discard the screws. 8. Attach the cable management arm to the rear of the unit with two 6-32 screws, supplied in the kit. Installation 11
ページ12に含まれる内容の要旨
9. Connect and route the cables through the cable management arm and unit opening. Installation is complete. Accessing the TFT7600 RKM 1. Gently extend the TFT7600 RKM until the slides lock. 2. Push the display release latch then lift the display. Removing the HP TFT7600 RKM To remove the TFT7600 RKM, reverse the order of the steps listed in the Installing the HP TFT7600 RKM (on page 8) section. Installation 12
ページ13に含まれる内容の要旨
Removing the HP 1U Adjustable Toolless Rails 1. Locate the spring release. 2. Place your hand on the outside of the HP 1U Adjustable Toolless Rails so that you can move the spring release. 3. Gently move the spring release toward the inside of the rack (1) while moving the HP 1U Adjustable Toolless Rails out toward you and away from the rack (2). NOTE: If you cannot gain access to the spring release from the outside of the HP 1U Adjustable Toolless Rails, a tool might be required t
ページ14に含まれる内容の要旨
2. Slide it back to release the locking mechanism and gently pull to remove the cable. Installation 14
ページ15に含まれる内容の要旨
Operational overview On-screen display The OSD buttons are used to operate the TFT7600 RKM OSD menus. Reference number Component Function 1 OSD scroll up and down Used to scroll in the OSD button menu and adjust the function 2 OSD activation button • Launches OSD menus • Selects • Exits menus and OSD Launching OSD menu To launch the OSD menu: 1. Press the OSD activation button on the front panel. The main menu displays on the screen. 2. To select a menu item, scroll up
ページ16に含まれる内容の要旨
• Use the Up (+) or Down (-) button to scroll through the OSD menu or an OSD sub-menu. The Up (+) and Down (-) button are also used to adjust or change a function setting. • Use the OSD activation button to select a sub-menu or a function. Example: To exit the OSD menu: 1. Press the Down (-) button to scroll to the Exit function. 2. Press the OSD activation button to select the Exit function and exit the OSD menu. OSD menu The OSD menu provides access to different display settings an
ページ17に含まれる内容の要旨
Vertical position The V position option displays a slider bar to enable the adjustment of the screen's vertical position. The center of the bar is obtained from the factory-preset value for Vertical Position. Clock The Clock option displays a slider bar to enable the adjustment of the Horizontal Clocks. Phase The Phase option displays a slider bar to enable the adjustment of the analog signals phase. Advanced The Advanced option provides access to the following options: • OSD se
ページ18に含まれる内容の要旨
Auto Configuration The Auto Configuration option performs four functions automatically: • Auto Level—Automatically adjusts the black and white levels of the screen • Auto Position—Automatically adjusts the position of the screen • Auto Phase—Automatically adjusts the phase • Auto Clock—Automatically adjusts the output clock per line to match the input Factory settings The Factory settings option enables the user to set the HP TFT7600 back to its original factory settings. The followi
ページ19に含まれる内容の要旨
Maintenance Maintenance and shipping guidelines This section covers maintenance and shipping guidelines for your TFT7600 RKM. To protect your unit from overheating and other types of damage: • Use only a power source and connection appropriate for this unit, as indicated on the marking label and back plate. • If an extension cord or power strip is used, be sure that the cord or strip is rated for the product. Also, be sure that the total ampere ratings of all products plugged into the e
ページ20に含まれる内容の要旨
Shipping the TFT7600 RKM Keep the original packing box in a storage area in case you must move or ship your RKM. Moving a rack with the TFT7600 RKM installed When moving the TFT7600 RKM installed in a rack, HP recommends that you install the lock plates, included in your kit, on each side of the unit and rack. To install lock plates: 1. Place the lock plate into the slot and rotate it back. 2. Insert one M6 screw into the hole on the lock plate, securing the unit to the rack. 3. Repe
