ページ1に含まれる内容の要旨
R
P2B-D / P2B-DS
®
Dual Pentium II Motherboards
USER’S MANUAL
Special Features
• P2B-DS
• Adaptec 7890 SCSI Chipset
• Adaptec 3860 SCSI Transceiver
ページ2に含まれる内容の要旨
USER'S NOTICE No part of this manual, including the products and software described in it, may be repro- duced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup pur- poses, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”). ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED
ページ3に含まれる内容の要旨
ASUS CONTACT INFORMATION ASUSTeK COMPUTER INC. Marketing Address: 150 Li-Te Road, Peitou, Taipei, Taiwan 112 Telephone: +886-2-2894-3447 Fax: +886-2-2894-3449 Email: info@asus.com.tw Technical Support Fax: +886-2-2895-9254 BBS: +886-2-2896-4667 Email: tsd@asus.com.tw WWW: www.asus.com.tw FTP: ftp.asus.com.tw/pub/ASUS ASUS COMPUTER INTERNATIONAL Marketing Address: 6737 Mowry Ave, Mowry Business Center, Building 2, Newark, CA 94560, USA Fax: +1-510-608-4555 Email: info-usa@asus.com.tw Technical Su
ページ4に含まれる内容の要旨
CONTENTS I. INTRODUCTION 7 How this Manual is Organized ........................................................... 7 Item Checklist ..................................................................................... 7 II. FEATURES 8 Features ............................................................................................... 8 The ASUS P2B-D/P2B-DS Motherboard ........................................... 9 III. INSTALLATION 10 ASUS P2B-D/P2B-DS Motherboard Layout .................
ページ5に含まれる内容の要旨
CONTENTS Power Management Setup........................................................... 49 Details of Power Management Setup .................................... 49 PNP and PCI Setup ..................................................................... 52 Details of PNP and PCI Setup ............................................... 52 Load BIOS Defaults .................................................................... 54 Load Setup Defaults ..................................................
ページ6に含まれる内容の要旨
FCC & DOC COMPLIANCE Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provid
ページ7に含まれる内容の要旨
I. INTRODUCTION How this Manual is Organized This manual is divided into the following sections: I. Introduction Manual information and checklist II. Features Information and specifications III. Installation Setting up the motherboard. IV. BIOS Software Setting up the BIOS software V. Support Software ASUS Smart Motherboard Support CD VI. Desktop Management BIOS supported Desktop Management Interface VII. ASUS LAN Card ASUS PCI-L101 Fast Ethernet PCI card installation (optional) VIII. Adaptec S
ページ8に含まれる内容の要旨
II. FEATURES Specifications II. FEATURES Features The ASUS P2B-D/P2B-DS motherboards are carefully designed for the demanding PC user who wants advanced features processed by the fastest CPU. ® • Multi-Speed: Supports Dual Intel Pentium II processors from 233MHz to 450MHz. • Intel AGPset: Features Intel’s 440BX AGPset with I/O subsystems and front-side bus (FSB) platform, which boosts the traditional 66-MHz internal bus speed to 100MHz. • Enhanced ACPI and Anti-Boot Virus BIOS: Features a pro
ページ9に含まれる内容の要旨
II. FEATURES The ASUS P2B-D/P2B-DS Motherboard 4 DIMM Sockets SEC CPU Slots Intel 440BX AGPset T: PS/2 Mouse B: PS/2 Keyboard T: USB Port 1 B: USB Port 2 COM 1 (Bottom) Parallel (Top) Serial (Bottom) COM 2 (Bottom) Accelerated Graphics Port Multi-I/O Chip 4PCI Slots Programmable 2Mbit Flash ROM Hardware Monitor 2 ISA Slots Adaptec AIC-7890 Intel PIIX4E Ultra2 SCSI Connector Ultra2 & Ultra-Fast/ PCIset Narrow SCSI Connector Wide SCSI Chipset Wide SCSI Connector (optional) ASUS P2B-D/P2B-DS User’
ページ10に含まれる内容の要旨
III. INSTALLATION Board Layout III. INSTALLATION ASUS P2B-D/P2B-DS Motherboard Layout PS/2 CPU_FAN MOUSE (TOP PORT) KEYBOARD (BOTTOM) BUS FREQ USB USB 1(TOP PORT) USB 2 (BOTTOM) COM 1 Intel 440BX AGPset COM 2 JP4 PWR_FAN JP5 Adaptec Accelerated Graphics Port AIC-3860 Transceiver 68-Pin Wide SCSI Connector Multi-I/O 35 68 1 34 Chip PCI Slot 1 50-Pin SCSI Connector R 1 SB-LINK™ 35 68 Connector 1 34 PCI Slot 2 68-Pin Ultra2 SCSI Connector Adaptec AIC-7890AB Chipset PCI Slot 3 CMOS Power (CR2032 3V
ページ11に含まれる内容の要旨
III. INSTALLATION Jumpers 1) CLRTC p. 13 Clear Real Time Clock (RTC) RAM 2) KBPWR p. 13 Keyboard Power Up (Enable/Disable) 3) FS0, FS1, FS2 p. 14 CPU Bus Frequency 4) CF1, CF2, CF3, CF4 p. 14 CPU Core:Bus Frequency Multiple 5) JP18 p. 15 Chassis Intrusion Sensor Setting (Enable/Disable) Expansion Slots/Sockets 1) DIMM Sockets p. 18 DIMM Memory Support 2) SEC CPU Slot p. 19 Single Edge Contact CPU Support * 3) SLOT1, SLOT2 p. 24 16-bit ISA Bus Expansion Slots † 4) PCI1, PCI2, PCI3, PCI4 p. 25 32-
ページ12に含まれる内容の要旨
III. INSTALLATION Jumpers III. INSTALLATION Installation Steps Before using your computer, you must complete the following steps: 1. Set Jumpers on the Motherboard 2. Install System Memory Modules 3. Install the Central Processing Unit (CPU) 4. Install Expansion Cards 5. Connect Ribbon Cables, Cabinet Wires, and Power Supply 6. Setup the BIOS Software 1. Jumpers Several hardware settings are made through the use of jumper caps to connect jumper pins (JP) on the motherboard. See motherboard lay
ページ13に含まれる内容の要旨
1 1 R R 1 1 III. INSTALLATION Jumper Settings 1. Clear Real Time Clock (RTC) RAM (CLRTC) The CMOS RAM is powered by the onboard button cell battery. To clear the RTC data: (1) Turn off your computer and unplug its AC power, (2) Short the two solder points labeled CLRTC, (3) Turn on your computer, (4) Hold down during bootup and enter BIOS setup to re-enter user preferences. Short the solder points to clear CMOS P2B-D/DS Real Time Clock RAM (CLRTC) 2. Keyboard Power Up (KBPK) This allow
ページ14に含まれる内容の要旨
1 R 1 III. INSTALLATION Jumpers III. INSTALLATION 3. CPU Bus Frequency (FS0, FS1, FS2) This option tells the clock generator what frequency to send to the CPU, DRAM, and 440BX AGPset. This allows the selection of the CPU’s External frequency (or BUS Clock). The BUS Clock multiplied by the BUS Ratio equals the CPU’s Internal fre- quency (the advertised CPU speed). 4. CPU Core:BUS Frequency Multiple (BF0, BF1, BF2, BF3) This option sets the frequency ratio between the Internal frequency of the
ページ15に含まれる内容の要旨
1 R 1 5. Chassis Intrusion Sensor Setting (JP18) (optional/reserved) This allows you to disable or enable the chassis intrusion sensor. Set to Enable if you want to use this function to monitor intrusion into your computer, for ex- ample, when the drive bay doors are opened. The default is set to Disable. JP18 JP18 Disable Enable (Default) P2B-D/DS Chassis Intrusion Sensor Setting ASUS P2B-D/P2B-DS User’s Manual 15 III. INSTALLATION Jumpers
ページ16に含まれる内容の要旨
(This page was intentionally left blank.) 16 ASUS P2B-D/P2B-DS User’s Manual
ページ17に含まれる内容の要旨
III. INSTALLATION 2. System Memory (DIMM) This motherboard uses only Dual Inline Memory Modules (DIMMs). Three sockets are available for 3.3Volt (power level) unbuffered Synchronous Dynamic Random Access Memory (SDRAM) of either 8, 16, 32, 64, 128, or 256MB to form a memory size between 8MB and 1GB. One side (with memory chips) of the DIMM takes up one row on the motherboard. To utilize the chipset’s Error Checking and Correction (ECC) feature, you must use a DIMM module with 9 chips per side
ページ18に含まれる内容の要旨
ページ19に含まれる内容の要旨
III. INSTALLATION 3. Central Processing Unit (CPU) This motherboard provides two Single Edge Contact (SEC) slots for Pentium II processors packaged in SEC cartridges. Pentium II Processor You should check to see that you have the following items: Lock Holes Captive Nut Pentium II Retention Mechanism Attach Mount Bridges The recommended heatsinks (see section on recommended heatsinks for more in- formation) for the Pentium II processor are those with three-pin fans that can be connected to the f
ページ20に含まれる内容の要旨
B Intel 440BX AGPset JP4 PWR_FA JP5 1 R 1 III. INSTALLATION CPU III. INSTALLATION Installing the Pentium II Processor 1. Connect the Heat Sensor Cable to JP4/JP5 (optional): If you purchased the specially designed fan and thermal monitor heatsinks, you may connect the heat sensor cables to the motherboard’s CPU heat sensor connectors (JP4/JP5) now. NOTE: If you are installing only one processor, you may use JP5 to connect a heat sensor cable to monitor the power supply temperature to make sure
