ページ1に含まれる内容の要旨
Transport GS12 / / / B5103G12S2
Revision 1.00
Copyright © TYAN Computer Corporation, 2004. All rights reserved. No part of this
manual may be reproduced or translated without prior written consent from TYAN
Computer Corp.
All registered and unregistered trademarks and company names contained in this
manual are property of their respective owners including, but not limited to the
following:
TYAN, Transport GS12 B5103G12S2 are trademarks of TYAN Computer Corporation.
Intel,
ページ2に含まれる内容の要旨
1 Table of Contents Before You Begin ............................................................................ 5 Safety Precautions ........................................................................... 4 1 Introduction .......................................................................................................... 7 1.1 Unpacking........................................................................................ 7 1.2 Product Description ..............................
ページ3に含まれる内容の要旨
LCD Driver.................................................................................... 30 Intel Application Accelerator......................................................... 31 ASF Alert Simulation and WatchDog Drivers............................... 31 ASF (Alert Standard Format) 2.0 SDK.......................................... 31 3.2 Installation Instructions for Linux (Red Hat/SuSE/Turbo Linux).. 33 Red Hat Linux 9.0 Installation Notes..........................................
ページ4に含まれる内容の要旨
6.3 About ASF 2.0 ............................................................................... 65 Set up Management Console ......................................................... 65 Check Agent and Management Console Link ............................... 66 Obtain Traps and Push Messages .................................................. 68 Remote Control.............................................................................. 69 7 Expanding the System.............................
ページ5に含まれる内容の要旨
Before You Begin This manual provides hardware-related information of the system for administrators who use it to develop and host web sites. The administrators should be familiar with operating systems and web browsers. Depending on the model purchased, your system may come with pre-installed software. For software information, refer to the documentation accompanying the software. Safety Precautions l Use the type of power indicated on the marking label. l Ensure that electrical circu
ページ6に含まれる内容の要旨
ページ7に含まれる内容の要旨
1 Introduction Congratulations on purchasing the system. This chapter introduces the features and functions of the product. 1.1 Unpacking After unpacking the shipping carton, you should find these standard items: P/N 431728700002 1× MiSERVER-WS112R case kit P/N 411728700101 (pre-installed) 1× S5103GNNR motherboard P/N 411715600004 (pre-installed) P/N 411715600005 (pre-installed) 1× button board 1× LCD module P/N 422715600051 (pre-installed) P/N 411728700106 (pre-install
ページ8に含まれる内容の要旨
And the following accessories: P/N 343728700001 1× heatsink P/N 451715600031 1× rail kit 1× primary IDE cable 1× secondary IDE cable 1× primary serial ATA cable 1× secondary serial ATA cable 1× HDD power to pinheader cable 2× SATA power cable 4× rubber feet 2× power cord (USA and Germany) 1× TYAN driver CD 1× B5103 User’s Manual Inspect all the items. If any item is damaged or missing, notify your dealer immediately. Keep the shipping carton and packing
ページ9に含まれる内容の要旨
1.2 Specifications NOTE: Specifications are subject to change without notice. Processor Networking • Single socket 478 • Two 1000Base-T, 100Base-TX, and 10Base-T Ethernet LAN ports (Intel • Intel Pentium 4 Northwood/Prescott processor 82541GI and 82547GI controllers) • Supports TCP, UDP, IPv4 Checksum • Supports 533/800 MHz FSB off-load Chipset Storage Capacity • Intel 875P MCH • Up to two PATA HDDs or two SATA HDDs • MCH+ICH-5R • SATA HDDs support RAID0, RAID1 (for • SMC LPC
ページ10に含まれる内容の要旨
1.3 System View Front View Ref Component Description Turns the power on and off (soft-off). Power Button Power Indicator Glows green when the power is on. LAN1 Indicator Indicates a network connection on LAN1 (external connection). LAN2 Indicator Indicates a network connection on LAN2 (internal connection). Hard Disk Drive Indicates activity on the hard disk drive. Indicator USB Ports Each of the two ports connects a USB device. LCD Screen Displays messages and val
ページ11に含まれる内容の要旨
Rear View Ref Component Description Ventilation Openings Maintain proper operating temperature. Do not cover or block the openings. Power Connector Connects the power cord. Power Switch Turns the main power of the system on and off. Connects the LAN cable for internal network connection. LAN1 Connector LAN2 Connector Connects the LAN cable for external network connection. Serial Port Connects a serial device. Connects an external CRT monitor. VGA Port USB Ports
ページ12に含まれる内容の要旨
ページ13に含まれる内容の要旨
2 Hardware Installation This chapter, which is divided into two sections, provides instructions on the hardware installation of the system. System Assembly section illustrates how to assemble each component of the system. Rack Mounting section describes the procedures for mounting the system into the rack. You can use the system assembly flowchart and the chart next to determine the proper sequence for removing or installing components to the server. Cabinet Cover CPU and Heatsink S
ページ14に含まれる内容の要旨
System Assembly Flowchart The following flowchart shows the basic procedures of system assembly: START CONNECT HARD DISK DRIVE CABLE AND POWER CORD REMOVE CABINET COVER CHECK IF ALL PARTS ARE PROPERLY CONNECTED INSTALL CPU AND HEATSINK REPLACE CABINET COVER INSTALL SYSTEM MEMORY FINISH INSTALL HARD DISK DRIVE 14 http://www.TYAN.com
ページ15に含まれる内容の要旨
2.1 System Assembly When installing a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter. Safety Considerations l Static electricity can destroy electronic devices. Whenever you handle an option outside of its protective packaging, first discharge any static electricity from your body by touching a protective grounding device or unpainted metal on the rear panel of the system before unplugging the power cord. l Before you
ページ16に含まれる内容の要旨
3. Lift the socket arm up to the vertical position. Align the new CPU so its Pin 1 corner (beveled corner) is at the Pin 1 corner of the socket. 4. Insert the CPU pins into the socket. Press the arm downward to the horizontal position. You will feel some resistance while doing so. This is normal as the pressure starts to secure the CPU in place. 5. Place the heatsink assembly on top of the CPU and align the four points of the heatsink socket. Secure with four screws following a diago
ページ17に含まれる内容の要旨
6. Replace the cabinet cover. Installing System Memory Your system has four 184-pin DIMM (Dual In-line Memory Module) sockets to support a maximum of 4 GB. You must follow these requirements for the DIMM to be used with the system: l Unbuffered DDR-SDRAM (Double Data Rate Synchronous DRAM) with ECC l PC2100/PC2700/PC3200-compliant l 2.5 V Follow this procedure to install a DIMM: 1. Open the cabinet cover (see previous section). 2. Locate the DIMM sockets. 17 http://www.TYAN.com
ページ18に含まれる内容の要旨
3. To install the DIMM, make sure the retaining clips are in the unlocked position, then align the DIMM’s notched end with the socket’s corresponding end and firmly insert the DIMM into the socket. Finally push the retaining clips inwards to lock the DIMM in place. 4. Replace the cabinet cover. Installing a Hard Disk Drive NOTE: Make sure that the jumper setting of the hard disk drive is set to “ Master.” (See the hard disk drive’ s documentation for information.) 1. Remove the cabin
ページ19に含まれる内容の要旨
4. Fit the bracket with a hard disk drive back into place and secure with one screw. If using an Ultra ATA/100 hard disk drive, connect the corresponding end of the included HDD power to pin header cable to the motherboard () and the other end to the hard disk drive () . Connect the included primary IDE data cable to the primary IDE connector on the motherboard () and the other end to the hard disk drive (). If using a Serial ATA hard disk drive, connect the included Serial ATA dat
ページ20に含まれる内容の要旨
5. Replace the cabinet cover. 6. You can create or rebuild RAID for the hard disk drive (see chapter 6 for information). 2.2 Adding a CD Drive You will need to use a CD drive when installing an operating system and its corresponding drivers (see chapter 3). WARNING: You are advised not to make frequent connection and disconnection on the IDE connector as this might cause damage to the data cable and connector pins. CAUTION: Follow the instructions in this section carefully. The DVD o
