ページ1に含まれる内容の要旨
SY-5SSM
SY-5SSM/5
V1.0
Motherboard
Quick Start Guide
™
T
C
ESS Audio SiS VGA DriverThe SOYO CD Quick BIOS Hardware Introduction
Driver Installation Setup Installation
Installation
RECYCLED PAPER
100%
POST CONSUMER
FOR HOME OR OFFICE USE
With FCC Standards FC
ested To Comply
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
T which is the Class B digital device complies with 47 CFR Parts 2 and 15 of the FCC rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The product was tested with the following configuration: Monitor: HITACHI/CM814U PS/2 Keyboard: DELL/GYUM90SK PS/2 Mouse: GENIUS/FSUGMZFC USB Mouse: WINIC/ F4ZFDM-A50 Printer: HP/DS16
ページ4に含まれる内容の要旨
SOYO ™ SY-5SSM & SY-5SSM/5 Motherboard ® m Y * These specifications are subject to change without notice 2 SY-5SSM & SY-5SSM/5 - Version 2.5 - Edition: June 2000 "http://www.soyo.com.tw". on the Internet. The address is Web Site If you need any further information, please visit our document is subject to change without notice. however, no guarantee is given as to the correctness of the contents. The information in this installing the Motherboard. Information in this guide has been carefully ch
ページ5に含まれる内容の要旨
SY-5SSM & SY-5SSM/5 Quick Start Guide 1 Introduction 1 Congratulations on your purchase of the SY-5SSM or SY-5SSM/5 Motherboard. This Quick Start Guide describes the steps for installing and setting up your new Motherboard. This guide is designed for all users to provide the basic steps of Motherboard setting and operation. For further information, please refer to SY-5SSM & SY-5SSM/5 Motherboard User's Guide and Technical Reference online manual included on the CD-ROM packed with your Mothe
ページ6に含まれる内容の要旨
SY-5SSM & SY-5SSM/5 Quick Start Guide SY-5SSM or SY-5SSM/5 Motherboard Layout y g P PS/2 KB PS/2 Mouse Connector Connector J1 2 4 6 8 10 0 S o 1 3 5 7 9 c .B. SRAM P 2 4 6 k US1 B US2 B e 64K X 64 t X 7 1 3 5 Power IDE2 IDE1 PRT COM2 COM 1 .B. SRAM P 64K X 64 1 N 1 N 8 7 VGA 6 5 1 1 SiS 530 4 3 2 1 Chipset D R JP32 e JOYSTICK s + Power e t P LED LINE-OUT W - R B KEY T LOCK A LINE-IN C P DIMM1 I++ L E- Speaker D MIC JACK DIMM2 + H D- - 1 D DIMM3 L E D 1 4 PCI Slot #1 1 3V 2 5 1 4 m PCI Slot #
ページ7に含まれる内容の要旨
SY-5SSM & SY-5SSM/5 Quick Start Guide 2 Installation 2 To avoid damage to your Motherboard, follow these simple rules while handling this equipment: l Before handling the Motherboard, ground yourself by grasping an unpainted portion of the system's metal chassis. l Remove the Motherboard from its anti-static packaging. Hold it by the edges and avoid touching its components. l Check the Motherboard for damage. If any chip appears loose, press carefully to seat it firmly in its socket. Follow
ページ8に含まれる内容の要旨
SY-5SSM & SY-5SSM/5 Quick Start Guide Install the Motherboard Follow the steps below in order to perform the installation of your new SY-5SSM or SY- 5SSM/5 Motherboard. Install the CPU ® To mount the Pentium class processor that you have purchased separately, follow these instructions. 1 2 3 4 1. Lift the socket handle up to a vertical position. 2. Align the blunt edge of the CPU with the matching pinhole distinctive edge on the socket. 3. Seat the processor in the socket completely and without
ページ9に含まれる内容の要旨
SY-5SSM & SY-5SSM/5 Quick Start Guide Set the CPU Voltage ( JP30) For CPUs that come with different voltages, please verify the correct voltage settings with your dealer before installation. Use the following table to set JP30 to the proper "voltage value", according to the specifications marked on your CPU: Voltage Setting: open short short short short The AMD K5 and K6 come in several versions with different voltages. Please verify the correct voltage settings with your dealer before installa
ページ10に含まれる内容の要旨
SY-5SSM & SY-5SSM/5 Quick Start Guide Voltage Setting: P166 open short open open open P200 The P55C (MMX) processors have the same voltage setting. P233 open short short short short The IDT X86 CPU C6/2 comes in several versions with different voltages. Please ask your dealer for the correct voltage. open short short open short open short open open open Set JP32, SW1 for CPU Frequency The DIP switch SW1 enable you to assign the Multiplier and Bus Clock, as shown in the following table: Fr
ページ11に含まれる内容の要旨
SY-5SSM & SY-5SSM/5 Quick Start Guide Frequency Multi- CPU Host Bus Setting: JP32 Multiplier: SW1 Processor Bus Clock plier 1-2 3-4 5-6 7-8 1-2 3-4 5-6 Cyrix 6x86MX PR200 66 MHz 2.5 x open short short short short short open Cyrix 6x86MX PR200 75 MHz 2.0 x open short short open short open open Cyrix 6x86MX PR233 75 MHz 2.5 x open short short open short short open Cyrix 6x86MX PR266 83 MHz 2.5 x open short open short short short open 66 MHz 3.5 x open short short short open open open Cyrix M II-30
ページ12に含まれる内容の要旨
SY-5SSM & SY-5SSM/5 Quick Start Guide Make Connections to the Motherboard This section tells how to connect internal peripherals and power supply to the Motherboard. Internal peripherals include IDE devices (HDD, CD-ROM), Floppy Disk Drive, Front Panel Devices (ACPI LED, Internal Speaker, Reset Button, IDE LED, and KeyLock Switch.), Wake-On-LAN card, and other devices. For more details on how to connect internal and external peripherals to your new SY-5SSM or SY-5SSM/5 Motherboard, please refer
ページ13に含まれる内容の要旨
SY-5SSM & SY-5SSM/5 Quick Start Guide Select the CPU Burst Mode (J1) There are two types of CPU burst modes according to manufacturer design: Ø Interleave Burst (CPU: Intel P54C/P55C, AMD K5/K6/K6-2/K6-III, IDT X86 CPU, Rise mP6) Ø Linear Mode (CPU: Cyrix 6x86/L/MX/M¢ )º ® l x ™ M ¢ º D ™ 1 1 2 2 If you are using a Cyrix ™ 6x86/L/MX/M II series CPU, set the burst mode to Linear by shorting jumper J1, and follow the following steps to select the correct Linear burst mode in BIOS: 1. During the
ページ14に含まれる内容の要旨
SY-5SSM & SY-5SSM/5 Quick Start Guide Enable/Disable the Onboard Sound (JP9) The onboard audio features of your Motherboard are controlled by jumpers JP9 Choose the available sound options among the following table: Clear CMOS Data (JP5) In some cases the CMOS memory may contain wrong data, follow the steps below to clear CMOS memory. 1. Clear the CMOS memory by momentarily shorting pin 2-3 on jumper JP5. This jumper can be easily identified by its white colored cap. 2. Then put the jumper back
ページ15に含まれる内容の要旨
SY-5SSM & SY-5SSM/5 Quick Start Guide 3 Quick BIOS Setup 3 After the hardware installation is complete, turn the power switch on, then press the key during the system diagnostic checks to enter the Award BIOS Setup program. The CMOS SETUP UTILITY will display on screen. Then, follow these steps to complete the quick BIOS setup. Select [LOAD SETUP DEFAULT] Select the “ LOAD SETUP DEFAULT ” menu and type “ Y ” at the prompt to load the BIOS optimal setup. Select [STANDARD CMOS SETUP]
ページ16に含まれる内容の要旨
SY-5SSM & SY-5SSM/5 Quick Start Guide 4 The SOYO CD 4 The SOYO-CD will NOT autorun if you use it on an Operating System other than Windows 9x or NT. Your SY-SY-5SSM & SY-5SSM/5 Super 7 ™ Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD contains the user's manual file for your new Motherboard, the drivers software available for installation, and a database in HTML format with information on SOYO Motherboards and other products. Insert the SOYO CD into the CD-ROM drive The SOYO
ページ17に含まれる内容の要旨
SY-5SSM & SY-5SSM/5 Quick Start Guide The user's manual files included on the SOYO CD are in PDF (Postscript Document) format. In order to read a PDF file, the appropriate Acrobat Reader software must be installed in your system. Note: The Start Up program automatically detects if the Acrobat Reader utility is already present in your system, and otherwise prompts you on whether or not you want to install it. You must install the Acrobat Reader utility to be able to read the user's manual file. F
ページ18に含まれる内容の要旨
SY-5SSM & SY-5SSM/5 Quick Start Guide driver revision: - SIS 530 VGA driver s SIS 530 busmaster drivers - SIS system hardware monitor - ESS Windows 9x drivers (for PCI) 4.05.00.1087 ESS Windows NT drivers (for PCI) 4.05.13 ESS Soundtrack Program (for PCI) V2.20 Cancel O K A short description of all available drivers follows: Ø The SiS VGA driver for windows 95/98 must be installed to make use of your on board VGA function. (For WinNT read the instructions in back of the Manual) Ø The SiS Busma
ページ19に含まれる内容の要旨
SY-5SSM & SY-5SSM/5 Quick Start Guide Check the Latest Releases Click the 'Check the latest Releases' button to go the SOYO Website to automatically find the latest BIOS, manual and driver releases for your motherboard. This button will only work if your computer is connected to the internet through a network or modem connection. Make sure to get your modem connection up before clicking this button. ) 17 The SOYO CD Step 3.
ページ20に含まれる内容の要旨
SY-5SSM & SY-5SSM/5 Quick Start Guide 5 SiS VGA Driver Installation 5 Introduction Your SY-5SSM V1.1 or SY-5SSM/5 V1.1 Motherboard is equipped with the SiS 530 chipset that offers extended graphics and text modes capabilities. To make use the advanced features of the SiS 530 chipset, you will need to install software drivers and application programs included on the CD-ROM. This section describes how to perform the SiS VGA driver installation for Microsoft Windows NT environment. The Windows
