ページ1に含まれる内容の要旨
SY-7IZM
Motherboard
Quick Start Guide
The SOYO CD Quick BIOS Hardware Introduction
Setup Installation
ページ2に含まれる内容の要旨
SOYO ™ SY-7IZM Motherboard * These specifications are subject to change without notice 2 7IZM Serial - Version 2.0 - Edition: April 1999 "http://www.soyo.com.tw". on the Internet. The address is Web Site If you need any further information, please visit our document is subject to change without notice. however, no guarantee is given as to the correctness of the contents. The information in this has been carefully checked for reliability; installing the Motherboard. Information in this guide T
ページ3に含まれる内容の要旨
1 Introduction 1 Congratulations on your purchase of the SY-7IZM Motherboard. This Quick Start Guide describes the steps for installing and setting up your new Motherboard. This guide is designed for all users to provide the basic steps of Motherboard setting and operation. For further information, please refer to SY-7IZM Motherboard User's Guide and Technical Reference online manual included on the CD-ROM packed with your Motherboard. Unpacking * If your board comes with a driver disc and a p
ページ4に含まれる内容の要旨
SY-7IZM Motherboard Layout B e r 0 CPUFAN X Power 1 3 4 1 L 1 3 r USB 1 USB 2 S o c 3V k Lithium e T t Battery COM 1 COM2 3 7 0 3 JP9 1 1 A FDC S S S Winbond D D D R R R 83977EF-AW A A A t M M M S Intel JOYSTICK F D 1IR l R a A 5 s M LINE-OUT 82443ZX h 11 B ATI I O LINE-IN 1 S E MIC JACK CDIN CODEC 4 CT1297 1 2 M M 1 M M 1 I I JP5 3 D D r A r 1 YMF740-V 2 e Intel g 82371 EB r 3 kr d +_ +_ 1 1 + + __ t To D N D D Key Features TM Ø Power-on by moden or alarm Ø Supports Intel Celeron p
ページ5に含まれる内容の要旨
2 Installation 2 To avoid damage to your Motherboard, follow these simple rules while handling this equipment: l Before handling the Motherboard, ground yourself by grasping an unpainted portion of the system's metal chassis. l Remove the Motherboard from its anti-static packaging. Hold it by the edges and avoid touching its components. l Check the Motherboard for damage. If any chip appears loose, press carefully to seat it firmly in its socket. Follow the directions in this section designed
ページ6に含まれる内容の要旨
Install the Motherboard Follow the steps below in order to perform the installation of your new SY-7IZM Motherboard. Install the CPU Record the working frequency of your CPU that should be clearly marked on the CPU cover. 300MHz (66 x 4.5) 333MHz (66 x 5.0) 366MHz (66 x 5.5) 400MHz (66 x 6.0) 433MHz (66 x 6.5) 466MHz (66 x7..0) 500MHz (66 x7.5) This Motherboard is designed to be able to support processors with 100MHz FSB. However, Socket 370 processors with 100MHz FSB are not available yet at t
ページ7に含まれる内容の要旨
Make Connections to the Motherboard This section tells how to connect internal peripherals and power supply to the Motherboard. Internal peripherals include IDE devices (HDD, CD-ROM), Floppy Disk Drive, Chassis Fan, Front Panel Devices (Turbo LED, Internal Speaker, Reset Button, IDE LED, and KeyLock Switch.), Wake-On-LAN card, VGA card, Sound Card, and other devices. For more details on how to connect internal and external peripherals to your new SY-7IZM Motherboard, please refer to SY-7IZM
ページ8に含まれる内容の要旨
Configure Memory Your board comes with two DIMM sockets, providing support for up to 256MB of main memory using DIMM modules from 8MB to 128MB with no restriction on memory configuration. Therefore, you can install memory modules in any combination. Set JP9 for power up FSB clock and AGP bus clock. JP9 is used to adjust AGP bus clock frequency depending on the value of the front side bus (FSB) clock, also the setting of the JP9 determines the power up FSB clock which will remain effective unti
ページ9に含まれる内容の要旨
Enable/Disable Power-On by Keyboard (JP10) You can choose to enable the Power-On by Keyboard function by shorting pin 1-2 on jumper JP10; otherwise, short pin 2-3 to disable this function. Power-On by Enable Disable Keyboard Short pin 1-2 to enable the Short pin 2-3 to disable the Power-On by Keyboard function. Power-On by Keyboard function. JP10 Setting 1 1 2 3 23 Clear CMOS Data (JP5) Clear the CMOS memory by momentarily shorting pin 2-3 on jumper JP5 for at least 5 seconds, and then by sh
ページ10に含まれる内容の要旨
The SY-7IZM Motherboard provides over-clocking capability. Due to the over-clocking setting your system may fail to boot up or hang during run time. If this occurs, please perform the following steps to recover your system from the abnormal situation: 1. Turn off system power. (If you use an ATX power supply, and depending on your system, you may have to press the power button for more than 4 seconds to shut down the system.) 2. Set JP9 to pin 1-2 if you use a FSB 66MHz CPU 3. Press and hold dow
ページ11に含まれる内容の要旨
3 Quick BIOS Setup 3 This Motherboard does not use any hardware jumpers to set the CPU frequency. Instead, CPU settings are software configurable with the BIOS [SOYO COMBO SETUP]. The [SOYO COMBO SETUP] menu combines the main parameters that you need to configure, all in one menu, for a quick setup in BIOS. After the hardware installation is complete, turn the power switch on, then press the key during the system diagnostic checks to enter the Award BIOS Setup program. The CMOS SETUP UTI
ページ12に含まれる内容の要旨
4 The SOYO CD 4 Your SY-7IZM Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD contains the user's manual file for your new Motherboard, the drivers software available for installation, and a database in HTML format with information on SOYO Motherboards and other products. Insert the SOYO CD into the CD-ROM drive The SOYO CD will auto-run, and the SOYO CD Start Up Menu will display as shown below. (SOYO CD Start Up Program Menu) The SOYO CD Start Up Program automatically detects w
ページ13に含まれる内容の要旨
Please note that if the Start Up program was unable to determine which SOYO Motherboard you own, the manual selection menu will pop up, as shown below. Then select the user's manual file that corresponds to your Motherboard model name and click OK. SOYO CD Manuals Please select your manual in the box below and click OK. 686 boards: 586 boards: 7IZ M O K Back (Manual Selection Menu) The user's manual files included on the SOYO CD can be read in PDF (Postscript Document) format. In order to re
ページ14に含まれる内容の要旨
The following drivers are available for Windows 95 (Driver Installation Menu) The following drivers are available for Windows 98 (Driver Installation Menu) However, to display the list of all drivers software available with SOYO Motherboards, click the Display all drivers on the SOYO CD button. Please make sure to install only the drivers adapted to your system, or otherwise this cause system malfunctions. 14 The SOYO CD Quick Start Guide SY-7IZM
ページ15に含まれる内容の要旨
Ø Intel Because Windows 95 does not recognize the Southbridge of the newer Intel chipsets (TX, BX, ZX etc) this utility has to be run, it will update the necessary Windows files. (Only for Windows 95) Ø SOYO Without the busmaster drivers the CPU will need to be involved every time data is read from or written to the Harddisk. The busmaster drivers make use of DMA (Direct Memory Access) to relieve the CPU of this burden, thus speeding up the system. The SOYO SpeedPro driver makes use of an ad
ページ16に含まれる内容の要旨
Ø With this application program the user can make use of the on board sound chip. Before installing the YAMHA 740 Sound Drivers, you MUST first install the YAMAHA 740 drivers for Windows 9x or NT. Ø Select this Item and click OK to start up the ATI Rage PRO AGP driver screen. Follow the instructions on the screen to install the drivers and/or application programs you need. Note: Once you have selected a driver, the system will automatically exit the SOYO CD to begin the driver installation pro
ページ17に含まれる内容の要旨
2 Select the Settings page. 3 Select Display Type.... 4 Select Change... from the display options. 5 Select Have Disk... 6 NT 4.0 will prompt you for the correct path. Enter D:\driv-all\ati-pro\winnt where D: is the drive containing the SOYO CD. 7 A list of [ATI] graphics accelerators will be displayed. Select the [ATI RAGE PRO TURBO AGP 2x], then click the OK button. 8 Windows NT 4.0 will once again prompt for confirmation. All appropriate files are then copied to the hard disk. 9 Restart Win
ページ18に含まれる内容の要旨
Soyo Computer Inc., (Taiwan) SOYO TECHNOLOGY CO., LTD. Tel: 886-2-2290-3300 Tel: 82-2-3272-6481 Fax: 886-2-2298-3322 Fax: 82-2-704-2619 Web Site: http://www.soyo.com.tw Web Site: http://www.soyo.co.kr/ E-mail: info@mail.soyo.com.tw Email:soyo@soyo.co.kr Email:soyok@chollian.net Soyo Tek Inc., (USA) Tel: (408) 452-7696 SOYO (U.K.) LTD. Fax: (408) 573-7696 Tel: 44-(0)181-569 4111 Web Site: http://www.soyousa.com Fax: 44-(0)181-569 4134 E-mail: sales@soyousa.com Web Site: http://www.soyo.nl Email:s
