ページ1に含まれる内容の要旨
SY-KT600 DRAGON
Plus
Motherboard
Quick Start Guide
The SOYO CD Quick BIOS Hardware Introduction
VIA 8237 Serial USB 2.0 Driver Audio Driver
Setup Installation
ATA Driver Installation Installation
Installation
ページ2に含まれる内容の要旨
SOYO™ 1. AGP cards running at 3.3V are not supported; only AGP cards running at 1.5V can be used in this mainboard. 2. Please read the user guide before proceeding with your installations. Serious damage may occur if the procedure is not followed properly. 3. If you have any problem getting your system to work, please follow the troubleshooting tips in your user guide. 4. For immediate Technical questions, please visit http://www.soyousa.com/support and http://www.soyousa.com/kb. 2
ページ3に含まれる内容の要旨
SOYO™ SY-KT600 DRAGON Plus Motherboard ® TM AMD K7 Athlon & Duron processors VIA KT600 AGP/PCI Motherboard 100/133/166/200 MHz Front Side Bus supported ATX Form Factor Copyright © 2003 by SOYO Computer Inc. Trademarks: SOYO is a registered trademark of SOYO Computer Inc. All trademarks are properties of their owners. Product Rights: All names of the product and corporate mentioned in this publication are used for identification purposes only. The registered trademarks and copyri
ページ4に含まれる内容の要旨
SY-KT600 DRAGON Plus Quick Start Guide 1 Introduction 1 Congratulations on your purchase of the SY-KT600 DRAGON Plus motherboard. This Quick Start Guide illustrates the steps for installing and setting up your new motherboard. This guide provides all users with the basic steps of motherboard setting and operation. For further information, please refer to the SY-KT600 DRAGON Plus motherboard User’s Manual that came with your motherboard. Unpacking When unpacking the motherboard, ch
ページ5に含まれる内容の要旨
SY-KT600 DRAGON Plus Quick Start Guide SY-KT600 DRAGON Plus Layout PS/2 KB P PS S//2 Mous 2 Mouse e Connector Connector USB3 / USB4 COM A COM B PRT FJ1 ATX Power 3 1 6 4 ABR 2 USB1 / USB2 / LAN 1 J30 8 7 MIC IN / Center & Bass out Line out / Front out 2 1 Line in / Rear out AGP Slot CD-SPDIFO 14 1 PCI Slot #1 2 14 ITE IT8705F PCI Slot #2 SATA2 SATA1 VT8237 IDE 2 IDE 1 PCI Slot #3 5 1 SIRCON PCI Slot #4 FDC1 VT6307 1 3V Lithium 3 Battery PCI Slot #5 ABR JP5 BUZZER 5511 ON 15 1 RJ2 2 10 6 1
ページ6に含まれる内容の要旨
SY-KT600 DRAGON Plus Quick Start Guide Key Features Supports AMD 462 pins Socket A processors: Athlon XP (Palomino/Thoroughbred/Barton) (200/266/333/400 CPU MHz FSB) Duron/Morgan Chipset AMD® KT600/ 8237 Chipset Supports PC2100, PC2700 and PC3200 DDR (non-registered and Memory ECC) memory modules. AGP 1x AGP master 4x/ 8x slot (1.5v only) PCI 5x 32-bit bus master PCI slots ITE IT8705F Super I/O controller supporting: Floppy disk controller Parallel port (SPP, EPP and ECP co
ページ7に含まれる内容の要旨
SY-KT600 DRAGON Plus Quick Start Guide USB 2.0 8x USB 2.0 compliant ports (4x on rear IO panel, 4x pin headers.) IEEE 1394 Onboard VIA VT6307 IEEE1394 Firewire controller with 2x pin header Sound VT1616 6 channel Audio Codec 10/100 MBps 100Base-T Ethernet controller, supporting Wake-On-Lan Network (WOL) Power Failure resume function to allow the system to turn on or off after a power failure, which is indispensable for server systems. Wake On Ring and Power On by Alarm to allow y
ページ8に含まれる内容の要旨
SY-KT600 DRAGON Plus Quick Start Guide 2 Installation 2 To avoid damage to your motherboard, please follow these simple rules while handling this equipment: Before handling the motherboard, ground yourself by touching on to an unpainted portion of the system's metal chassis. Remove the motherboard from its anti-static packaging. Hold the motherboard by the edges and avoid touching its components. Check the motherboard for damage. If any chip appears to be loose, press carefully
ページ9に含まれる内容の要旨
SY-KT600 DRAGON Plus Quick Start Guide Install the Motherboard We will now begin the installation process. Please follow the step-by-step procedure designed to lead you to a complete and correct installation. Step 1- Install the Central Processing Unit (CPU) Step 2- Install memory modules Step 3- Install expansion cards Step 4- Connect cables, case wires, and power supply Step 1. Install the CPU TM TM TM ® CPU Mount Procedure: To mount the AMD K7 Athlon , Athlon XP & Duron processor
ページ10に含まれる内容の要旨
SY-KT600 DRAGON Plus Quick Start Guide 5. Set the jumpers on the FJ1 jumper block to the correct FSB for your CPU. FJ1 100 MHz 133 MHz 166 MHz 200 MHz 3 6 3 6 6 3 3 6 Clock Select 5 2 5 2 5 2 5 2 4 1 4 1 4 1 4 1 RJ2 Dipswitch This dipswitch sets the ratio of your CPU. Note that this switch will only work if you have an unlocked CPU. OFF=1 SW ： ON=0 RATIO UNDER 12.5 FID Codes for SW 1 ~ 7 Four-Bit Clock Four-Bit Clock FID Multiplier FID Multiplier 0000000 11.0 0000010 7.0 11.5 0010
ページ11に含まれる内容の要旨
SY-KT600 DRAGON Plus Quick Start Guide CPU Fan Installation Your Socket A processor kit comes with a cooling fan. Mount the fan on the processor according to the instructions provided by the manufacturer. The fan is a key component that will ensure system stability. The fan prevents overheating, therefore prolonging the life of your CPU. Note: Remember to connect the fan to the appropriate power source. CPU Fan Mount Procedure: To prevent scratch or damage on the motherboard, please f
ページ12に含まれる内容の要旨
SY-KT600 DRAGON Plus Quick Start Guide 2. Carefully mount the fan on top of the CPU and clip-on the first lock. 1 3. Clip-on the second lock and please make sure not to damage/scratch the board. 2 12 Hardware Installation
ページ13に含まれる内容の要旨
SY-KT600 DRAGON Plus Quick Start Guide 4. Connect the power connector to CPUFAN1. Note: If the fan is defective or Power connector is not connected to CPUFAN1, the system will enable Fan Off Control function. See below for more information on FOC function. When the CPU temperature exceeds, the temperature set in the CPU Temp. Protection in BIOS setup, SOYO’s Anti Burn Regulator (ABR) will automatically shutdown the system and beep until the power button is pressed for one time. 13 Ha
ページ14に含まれる内容の要旨
SY-KT600 DRAGON Plus Quick Start Guide FOC (Fan-Off Control) The newly designed SOYO “FOC” is based on the concept of total protection for the CPU, which is very different from what is currently seen on the market. The H/W control function is used to see a passive security system of monitoring and warning. S/W Simultaneous Signal Follow-up techniques and Auto Power Off System are included to prevent possible damage caused by the malfunctioning of the CPU fan. With the help of “O/S On Time
ページ15に含まれる内容の要旨
SY-KT600 DRAGON Plus Quick Start Guide ABR (Anti Burn Regulator) SOYO's ABR (Anti Burn Regulator) is a specially designed hardware circuit that works hand in hand with the CPU’s internal sensor in monitoring the temperature of the CPU and prevent it from overheating. Once the heat accumulated in the CPU is over the set limit. ABR will automatically shut down the system power and warn you with a beeping sound. To de-activate the beeping sound, un-plug the AC power cord. We recommend you t
ページ16に含まれる内容の要旨
SY-KT600 DRAGON Plus Quick Start Guide Step 3. Installation of Expansion Cards The motherboard has 1 AGP slot and 5 PCI slots. 1. Read the related expansion card’s instruction document before inserting the expansion card into the computer. 2. Press the expansion card firmly into expansion slot in the motherboard. 3. Make sure the metal contacts on the card are correctly seated in the slot. 4. Replace the screw to secure the slot bracket of the expansion card. 5. Install driver for the op
ページ17に含まれる内容の要旨
SY-KT600 DRAGON Plus Quick Start Guide USB20_3 / USB20_4 Pin1 Pin2 Pin3 Pin4 Pin6 Pin7 Pin8 Pin9 Pin10 VCC Data(-) Data(+) GND VCC Data(-) Data(+) GND GND 1394: FW1 Pin1 Pin2 Pin3 Pin4 Pin5 Pin6 Pin7 Pin8 Pin9 Pin10 A0PC GND B0PC NC PWR0 A0MC CGND B0MC PWR0 CGND 1394: FW2 Pin1 Pin2 Pin3 Pin4 Pin5 Pin6 Pin7 Pin8 Pin9 Pin10 A1PC GND B1PC NC PWR1 A1MC CGND B1MC PWR1 CGND CPU Cooling Fan: CPUFAN1 CPU Cooling Fan: CPUFAN2 Pin1 Pin2 Pin3 Pin1 Pin2 Pin3 GND 12V SENSOR GND 12V NC Chassis Fa
ページ18に含まれる内容の要旨
SY-KT600 DRAGON Plus Quick Start Guide CMOS Clear (JP5) In some cases the CMOS memory may contain wrong data, follow the steps below to clear the CMOS memory. 1. Clear the CMOS memory by momentarily shorting pin 2-3 on jumper JP5. Its white cap can easily identify this jumper. 2. Put the jumper back to 1-2 to allow writing of new data into the CMOS memory. CMOS Clearing Clear CMOS Data Retain CMOS Data Short pin 2-3 for Short pin 1-2 to JP5 Setting at least 5 seconds to retain
ページ19に含まれる内容の要旨
SY-KT600 DRAGON Plus Quick Start Guide 3 Quick BIOS Setup 3 This motherboard allows you to change your memory and onboard peripheral settings in BIOS setup. After the hardware installation is complete, turn the power switch on, then press the key during the system diagnostic checks to enter the Award BIOS Setup program. The CMOS SETUP UTILITY will be shown on the screen. Then, follow these steps to configure your system. Step 1. Select [STANDARD CMOS SETUP] Set [Date/Time] and
ページ20に含まれる内容の要旨
SY-KT600 DRAGON Plus Quick Start Guide 4 The SOYO CD 4 The SOYO-CD will Auto Run only in Windows Based Operating Systems. Your SY-KT600 DRAGON Plus motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD contains a. The user's manual for your new motherboard in PDF format, b. The drivers software available for installation, and c. A database in HTML format with information on SOYO motherboards and other products. Step 1. Insert the SOYO CD into the CD-ROM drive If you a
