ページ1に含まれる内容の要旨
RS-232 to Bluetooth
Quick Installation Guide
Introducing the RS-232 to Bluetooth
The RS-232 to Bluetooth converter allows any device with
an RS-232 port to communicate wirelessly.
Features and Benefits
• Replaces RS-232 cable
• Full Bluetooth 2.0 support + EDR
• Easy to configure baud rate and master or slave role
selectable
• Supports baud rates up to 115.2 K bps
• 300 feet ( Enhanced Antenna ); CLASS 1
System Requirements
• Pentium II or equivalent PC
Windows 2000 and above
Package Contents
ページ2に含まれる内容の要旨
Layout Figure 1: Layout LED Indicators See Figure 2 on the next page for the location of the LEDs. • Red: Power indicator - on all the time. • Green: Before connecting to synchronize between the serial device and the BT RS232 Config Tool software, the green LED will be blinking.After connecting to synchronize between the device and the BT RS232 Config Tool software, the green & red LED will blinked alternately. DC-In Power Jack Connect the power adapter to the power jack then plug the power
ページ3に含まれる内容の要旨
Power Jack Antenna Connector LEDs Figure 2 Antenna Connector The connector is a standard Reverse SMA jack. Simply connect it to a 2.0dBi, 50 Ohms impedance dipole antenna to support 2.4 GHz frequency. (The Antenna is changeable for high gain Antenna), see Figure 2. RS-232 (Serial) Connect the RS-232 port into the device as you would with any computer and serial device, see Figure 3. Figure 3: RS-232 3
ページ4に含まれる内容の要旨
Set-up Button Set-up button Figure 4 The purpose of the Set-up Button is for synchronizing between RS-232 to Bluetooth Converter and BT RS232 Config Tool software. Hardware Installation 1. Connect the RS-232 to Bluetooth Converter to serial port of the PC. Connect the DC power adapter and jack into power outlet and DC-in outlet. You will see the red LED is going to be on and the green LCD will blink. 2. After running the BT RS232 Config Tool and finish configuration. Click the Connect icon in
ページ5に含まれる内容の要旨
BT RS232 Config Tool Installation & Setup When setting up RS-232 to Bluetooth Converter for the first time, you have to install and run BT1.exe as BT RS232 config tool first in your computer device. The utility CD is enclosed in the device box. Before you use RS-232 to Bluetooth Converter, you have to pair it with another E- BT232 device. The RS-232 to Bluetooth Converter must be configured first before you use it. The purpose of configuration is to pair two devices for an exclusive connection b
ページ6に含まれる内容の要旨
• SB-232 Config Tool Parameters Configuration Figure 6 After double click the icon of BT1 as BT RS232 Config Tool, the configuration screen will be pop-up as the above picture. A. COM Port Select COM port number, you have to avoid port conflict with other devices in the computer, use an available port number B. Device Name Select device name is for identifying each device. You can follow the name by tool access or retyping the new name yourself. C. Local Address Local address will be automatical
ページ7に含まれる内容の要旨
E. PIN Code Device uses a PIN Code to identify during connecting and communication. F. Role Role is for identifying the role of the device as a master or slave. Select Master, for DTE mode, for Data Terminal Equipment (such as a PCs). Select Slave for DCE mode, for Data Communication Equipment (such as a Modem). G. Discoverable Allows or denies the device detection by other Bluetooth devices. H. Baud Rate The baud rate range is 1200 bps-15.2K bps depending on transmission distance and envi
ページ8に含まれる内容の要旨
Apply Connect Figure 7 After finish the parameters configuration, click the Connect icon in BT RS232 Config Tool screen and immediately press the Set-up button on the left side of the device. Connect is changed to Disconnect when connection is successfull. 8
ページ9に含まれる内容の要旨
Apply Write Figure 8 Click Write, to save all parameters after configuring into the BT RS232 Config Tool. Apply Read Figure 9 9
ページ10に含まれる内容の要旨
Clicking Read loads all parameters saved from the last configuration of the BT232 Config Tool. RS-232 Pin Assignment The pin assignment scheme for a 9-pin male connector on a DTE is given below Pin1: X Pin 6: DTR Pin 2: TXD Pin 7: CTS Pin 3: RXD Pin 8: RTS Pin 4: DSR Pin 9: DC 5V Pin 5: GND RS-232 Wiring Diagram Serial Device SB-232 Converter 2 RX 2 TX 3 TX 3 RX 5 GND 5 GRN 4 DTR 4 DSR (Flow Control) 6 DSR 6 DTR (Flow Control) 10
ページ11に含まれる内容の要旨
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analysts will promptly respond. SIIG offers a 5-year manufacturer warranty with this product. Please see our web site for more warranty details. If you encoun
ページ12に含まれる内容の要旨
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCIe, PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), networking, sound cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty. High-quality control standards are evide
