ページ1に含まれる内容の要旨
CyberPro PCI 2S
Quick Installation Guide
Introducing the CyberPro PCI 2S
The CyberPro PCI 2S high-speed serial I/O card provides
two additional 9-pin serial ports.
Features and Benefits
• Conforms to PCI v2.2 Plug and Play
• Full support for Windows-based software
• Reduces CPU load and improves system
performance dramatically
• IRQ sharing feature reduces IRQ conflicts
• High-speed serial port (9-pin) works with 56K V.90
external modems, ISDN terminal adapters, PDAs,
digital cameras, label prin
ページ2に含まれる内容の要旨
Package Contents • CyberPro PCI 2S board • Driver CD • Quick installation guide Layout JP2 (Serial port 2) Serial Port 2 JP1 (Serial port 1) Serial Port 1 Figure 1. Layout Jumper Settings (JP1, JP2) Open = 0 volts (default) Short 1-2 = 5V Short 2-3 = 12V Note: Most serial devices do not require additional power through the serial port. Refer to your serial device's manual for more information. 2
ページ3に含まれる内容の要旨
Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer’s case for a few seconds. Avoid any contact with internal parts and handle cards only by their external edges. 1. Turn OFF the po
ページ4に含まれる内容の要旨
Driver Installation This section provides information on how to install the CyberPro PCI 2S drivers. Windows 7 (32-/64-bit) 1. Right click Computer, click Manage, click Device Manager. 2. Insert the driver CD. Right click PCI Serial Port, click Update Driver Software. 3. Click Browse my computer for driver software. 4. Type D:, then click Next. (Change D: to match your CD/DVD-ROM drive letter) 5. At Windows has successfully updated your driver software, click Close. 6 Right click Other PCI Bri
ページ5に含まれる内容の要旨
3. Repeat step 2 to complete the driver installation. Note: Windows Vista driver installation process may take several minutes to complete. Windows XP (32-/64-bit) / Server 2003 (32-/64-bit) 1. At the Found New Hardware Wizard, insert the driver CD. 2. Select No, not this time, click Next. (Skip this step if not prompted) 3. Select Install the software automatically (Recommended), then click Next. 4. Click Finish. 5. Repeat steps 1-4 two more times. 6. Restart Windows to complete the installati
ページ6に含まれる内容の要旨
To Verify Windows 7 / Vista / XP / Server 2003 & 2008 Installation 1. Check in Device Manager to verify installation. For Windows 7: Right click Computer, click Manage, then click Device Manager. For Windows Vista: Right click Computer, click Manage, click Continue, then click Device Manager. For XP / Server 2003: Right click My Computer, click Manage, then click Device Manager. For Server 2008: Right click Computer, click Manage, double click Diagnostics, then click Device Manager. 2. Click on
ページ7に含まれる内容の要旨
To Verify Windows 2000 Installation 1. Right click My Computer, click Manage, then click Device Manager. 2. Click on the + (plus sign) in front of Ports (COM & LPT), CyberSerial 16Cxxx... should be displayed two times. 3. Double click Multifunction adapters, SIIG CyberPro 2S board should be displayed. Windows ME 1. At the Add New Hardware Wizard, select Specify the location of the driver (Advanced), then click Next. 2. Insert the driver CD, check Specify a location, uncheck the other box, type i
ページ8に含まれる内容の要旨
5. Repeat steps 1-4. 6. Restart Windows to complete the installation. Windows 95 1. At the Update Device Driver Wizard, click Next. 2. Insert the driver CD, click Other Locations. 3. Type in D:\9x, click OK, then click Finish. (Change D: to match your CD/DVD-ROM drive letter) 4. From the Insert Disk window, click OK. When the Copying Files dialog box pops up, type in D:\9x, then click OK. (Change D: to match your CD/DVD- ROM drive letter) 5. Restart Windows to complete the installation. To Ver
ページ9に含まれる内容の要旨
5. Click Yes, then click Exit. 6. Restart Windows to complete the installation. To Verify Windows NT 4.0 Installation 1. Click Start, Settings, Control Panel. Double click Ports device icon. 2. Two new COM ports will be assigned when successfully installed. 9
ページ10に含まれる内容の要旨
Changing COM Port Address Some serial devices need a specific COM port in order to work. If your serial device works properly, do not change this setting. Windows 7 / Vista / XP / Server 2003 & 2008 / 2000 1. From the Device Manager window double click Ports (COM & LPT), then double click the CyberSerial serial port you want to change. 2. Click Settings tab and click Advanced. 3. Click the down arrow that is next to the COM Port number box and select a COM port that is not in use. Click OK. 4.
ページ11に含まれる内容の要旨
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analysts will promptly respond. SIIG offers a lifetime manufacturer warranty with this product. Please see our web site for more warranty details. If you enco
ページ12に含まれる内容の要旨
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCIe, PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), networking, sound cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty. High-quality control standards are evide
