ページ1に含まれる内容の要旨
M38C29T-ADF
Temporary Target Board for M38C29RLFS
User’s Manual
Keep safety first in your circuit designs!
Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products
better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to
personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with
a
ページ2に含まれる内容の要旨
1. Things to Check When Unpacking The M38C29T-ADF package consists of the following products. When unpacking your package, check to see that all of these components are included. If you find any item missing or faulty, or any suggestion, contact your local distributor. Table 1.1 Package components Item M38C29T-ADF temporary target board M38C29T-ADF User’s Manual (this manual) 2. Outline The M38C29T-ADF is a temporary target board used to develop software with a compact emulato
ページ3に含まれる内容の要旨
4. Setting Up This chapter describes how to set up the M38C29T-ADF. (1) Mount the emulator MCU on the M38C29T-ADF. After checking the position of the No. 1 pin of the emulator MCU, mount the emulator MCU referencing Figure 4.1. (2) Insert the connector on the tip of the emulator probe to the socket on the emulator MCU. For the M38000T2-CPE, the converter board PCA4933 is required between the emulator probe and emulator MCU. No. 1 pin M38C2 9T - ADF J2 J1 1 26 100 75 IC1 100 81 1
ページ4に含まれる内容の要旨
(3) Connect the RESET cable (white) and the GND cable (black) of the emulation pod to the RESET (TP3) pin and Vss (TP2) pin of the M38C29T-ADF respectively. And connect the Vcc cable (red) to the Vcc (TP1) pin. (4) Set the MCU type select switch of the M38000T2-CPE to the RLSS side. (5) Connect a power supply (not included) to the Vcc (TP1) pin of the M38C29T-ADF. And connect the GND output of the power supply to the Vss (TP2) pin. Use the power supply whose rising time is 10ms or less.
ページ5に含まれる内容の要旨
(6) Setting SW Set the SW1 to SW4 according to your application. Table 4.2 describes the functions of the SW1 to SW4. Table 4.2 Functions of the SW1, SW2, SW3 and SW4 of the M38C29T-ADF No. Name Function Factory-setting SW1 PORT/XCIN Allows you to choose whether to supply the sub-clock signals (32.768kHz) to the PORT MCU's XCIN pin (pin 43). To use P61/XCIN as an output port, choose the PORT side. To use the sub-clock signals, choose the XCIN side. SW2 VREF Allows you to choose whethe
ページ6に含まれる内容の要旨
5. Oscillator Circuit 5.1 Oscillator Circuit Board The M38C29T-ADF has a built-in oscillator circuit board on which a 4.0MHz oscillator is mounted. Figure 5.1 shows an external view of the OSC-2 oscillator circuit board (bare board) and where connector pins are located. Figure 5.2 shows the circuitry of the OSC-2 oscillator circuit board (bare board). Use the number of oscillator circuits recommended by the oscillator manufacturer. J1-4: GND J1-3: Oscillation output J1-2: GND J
ページ7に含まれる内容の要旨
6. Reset Circuit Figure 6.1 shows the reset circuit and its waveform. In this product, reset is cleared in about 100ms from the instant Vcc passes about 2.1V after having started from 0 V. When Vcc drops down to about 2.1V, reset turns effective. Detected power voltage ( ) V Approx. 1.25x (R3 + R4 )/ R4 TP3 Vcc RESET IC3 1 R5 R3 Vcc 10K 6.8K MCU RESET 2 5 IN OUT M51957BL R4 SW4 Vss CD 10K 3 4 C5 0.33u F ＣＤ 1.25V Input volage (IC3-2-pin ） ｔ H td td Output state (IC3- 5-pin ） L ｔ td
ページ8に含まれる内容の要旨
7. Pin Layout Figure 7.1 shows the pin layout of the M38C29T-ADF. IC1 1 100 NC J1-1 NC J1-100 2 99 NC J1-2 NC J1-99 3 98 P04 J1-3 NC J1-98 97 4 P05 J1-4 NC J1-97 5 96 P06 J1-5 NC J1-96 6 95 J1-6 P07 NC J1-95 7 94 P10 J1-7 NC J1-94 8 93 P11 J1-8 P03 J1-93 9 92 J1-9 P02 P12 J1-92 10 91 J1-10 P01 P13 J1-91 11 90 P14 J1-11 P00 J1-90 12 89 P15 J1-12 P57 J1-89 13 88 P16 J1-13 P56 J1-88 14 87 J1-14 P17 J1-87 P55 15 86 J1-15 P54 P20 J1-86 16 85 J1-16 P21 P53 J1-85 17 84 J1-17 P22 P52 J1-84 18
