ページ1に含まれる内容の要旨
Jiva TP/LT- 5700G/5800G
Touch Control Work Station
User’s Manual
Rev. A0
FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause interference
to radio communications. It has been tested and found to comply with limits for a Class
A digital device pursuant to subpart J of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference wh
ページ2に含まれる内容の要旨
Standard Features: a) CPU: Celeron compatible C3 800 MHz or up for Jiva TP/LT-5700G; C3 1.0GHz for Jiva TP/LT-5800G b) A base design supporting optional UPS battery storage c) Support Win98, Win 2000, Win CE, Win XP Pro and Linux environment for Jiva TP/LT-5800G d) Support Win CE.NET on CF card or Linux LAN boot for Jiva TP/LT- 5700G e) High quality 15” TFT active matrix LCD panel f) Vertical type LCD panel with easy tilt angle adjustment from 18° to 87° g) Resistance type (InfraRed
ページ3に含まれる内容の要旨
XP Pro Optional Items: Note: The underlined items in the following list means that option must be set prior to shipment from the factory. The rest items can be set by the dealers. a) DDR266 SDRAM memory expansion up to 1GB b) Audio amplifier circuit and a pair of speakers in cable cover area c) Side mount upgrade kit among: Deluxe security device upgrade (KP100) covering keypad and option(s) from KB interface MSR, smart card reader and finger print sensor Common security device up
ページ4に含まれる内容の要旨
INSTALLATION GUIDES CAUTION: Before any installation or cable connection to the set, please always make certain that the system is turned off and the external power source to the set is removed to prevent electric hazard! Never touch any metal pin in the connectors or circuits to avoid high voltage hazard or electrostatic discharge damage unless the operator is well grounded. Failure to do the above will void the product warranty! OPENING CABLE COVER Please first push the lock/release
ページ5に含まれる内容の要旨
CONNECT/DISCONNECT CABLES After removal of the cable cover, the connector area will be accessible then. Please disconnect every cable before separation of main unit and the adjustable stand assembly. When later the main unit and stand assembly are to be re-assembled for application, please connect all required cables to the appropriate connectors. Please make sure that each connector is connected to the right port with the correct orientation. Damages due to incorrect connection or orie
ページ6に含まれる内容の要旨
applied when later on the main unit and the stand assembly have to be reunited. OPENING STAND ASSEMBLY Take the adjustable stand assembly and turn it up side down to show the bottom of the base. Now, unscrew the 2 screws on the cable passage cover and take the cable passage cover away to show the cable passage. If there is no need to install the optional UPS battery here, please skip Screws the next paragraph and start routing cables through the cable passage. Cable Otherwise, ple
ページ7に含まれる内容の要旨
Connect the 6 pole plug of CCBLA-238 to “CR” port and connect each 8 pole plug to the connector marked “signal cable from POS Printer” at the rear of one of the cash drawer. In this way, the Jiva series is capable of controlling two cash drawers independently through software command. ROUTING THE CABLES Fix this End of the Cover First Route Cables under the Cover Connect this End to Main Unit This End to Other Devices Place all the cables required for connections to the
ページ8に含まれる内容の要旨
required to support the system real time clock. The jumpers in this window are designated for VGA port and COM port power supply function. Please consult your dealer for technical support on setup of these jumpers. A new Lithium battery can support the system RTC for about 3 years. After the battery is nearly exhausted, the user must change a new battery otherwise the system RTC and system configuration setup will be lost. INSTALLING UPGRADE KIT Please follow the instructions in the man
ページ9に含まれる内容の要旨
Posiflex wireless connection driver elements. The driver can be found together in delivery of the wireless printer or the Posiflex Product Information CD of version 1.9 or above, or please find it on our web http://www.posiflex.com or http://www.posiflex.com.tw JOINING MAIN UNIT AND STAND Matching Pegs Matching Holes Round Part Slot Part Removal Hollow Match the matching pegs on the back of the main unit against the matching holes on the stand. First aim the matchin
ページ10に含まれる内容の要旨
WALL MOUNTING The major part in the wall mounting kit is a bracket as shown in the picture. Screw the bracket against the wall for mounting the Jiva TP/LT- 5700G / Jiva TP/LT-5800G in the direction that the wider parts of the matching holes are at the top as shown in the picture below. Align the four matching pegs on the back of the main unit with the four matching holes in the bracket to hold the main unit in the similar manner as installing the main unit onto the stand assembly. The st
ページ11に含まれる内容の要旨
the software system on HDD collapses, it is possible to restore the operating system onto a physically intact HDD with use of the Recovery CD that comes with the preloaded operating system. Please follow the instruction from your system integrator for system / software restoration. Follow the instructions below for operating system recovery only if your system integrator does not advise otherwise. For the Jiva TP/LT-5800G preloaded with Windows XP Pro or Windows 98 on HDD, Posiflex prov
ページ12に含まれる内容の要旨
USING THE TOUCH POS APPLICATION ENVIRONMENT It is very important that you check the following operational guidelines: Ventilation This terminal must NOT be operated in an environment with restricted ventilation. The installation should be such that there is at least 25mm air clearance around any top or side ventilation holes. The installation must also be such that there is a free flow of air around the unit at ALL times. Operating Environment The equipment must not be operated or st
ページ13に含まれる内容の要旨
well-maintained battery can be expected to provide adequate service for 1 year. Battery replacement: In the power management circuit in this POS system, there is a handy battery monitor feature to help user find out when an UPS battery should be replaced. The battery monitor will always first measure and check the UPS battery to see if the UPS battery is already incapable of service or if there is any sign for the possible critical fault development in the battery before it allows the c
ページ14に含まれる内容の要旨
conditions is summarized in following table: LED Status System Status External Power UPS Battery Powering Up Off Off Off Not present Not possible Off Off Off Present Not allowed Green Off On No influence Allowed Blue On On No influence Not required Blue/flash On Off Activated Not required Green/rapid Running at On Off Not required flash low capacity Hardware Power Switch The power switch located at left side of the main unit is a slide type switch. This switch controls the power on
ページ15に含まれる内容の要旨
AUTOMATIC POWER ON There are several ways supported by this system to perform an automatic boot up as long as external power is supplied to the system. Procedures for each method are described below. By RTC Alarm preset 1. Preset the system to timely boot up by pressing “Del” key at powering up this system to enter system BIOS CMOS setup. 2. Select “Power Management Setup” and enter “PM Wake Up Events”. Go to item “Power Up by Alarm” and change the setting to “Enabled”. 3. Alarm setu
ページ16に含まれる内容の要旨
mode dual display function for Win98 or WinXP. To support the DC power to these Posiflex monitor, use the DC adaptor to connect into the monitor or VGA cable or purchase another type of VGA cable and set an internal jumper in Jiva TP/LT-5700G or Jiva TP/LT-5800G to supply the required power through the VGA connector. SYSTEM PROTECTION In the Posiflex POS system delivered with preloaded OS, there is a function built in for system protection. A screen as below will pop up for a short per
ページ17に含まれる内容の要旨
Please be solemnly alerted that the system restore operation means the irrecoverable erasement of existing data or system setup, it is strongly advised to press “Esc” key to avoid such miserable damage if there is any doubt. Pressing “F4” key at this screen will save the current status of the whole system and the earlier saved status will be cleared at the same time. Therefore, please do this save only when you know that your current system status is “safe” and “clear”. Pressing “F3”
ページ18に含まれる内容の要旨
SOUND PORTS The audio port on Jiva TP/LT-5700G / Jiva TP/LT-5800G supports a Microphone in and a line out jacks. The internal audio output port supports line output signals and requires power amplifier for connection to speaker unless the option of audio amplifier and a pair of slim type speakers built in the cable cover area are ordered at the beginning. LAN BOOT If the system integrator arranges the TP/LT5700G to boot from a LAN server, he may have revised the system BIOS installed i
ページ19に含まれる内容の要旨
Posiflex Touch Terminal Manager A program named “Posiflex Touch Terminal Manager” is installed in the preloaded Windows system with a PS/2 interface touch panel controller. This program can also be obtained by download from the POSIFLEX web site. This program can be engaged in the program group “Posiflex Tools” and it controls the beep generated when the touch panel is touched, the detail in right button click emulation, and also provides touch panel re-calibration. RS232 Touch Controll
