ページ1に含まれる内容の要旨
ND-45504 (E)
ISSUE 2
PART OF STOCK # 151900
®
Circuit Card Manual
DECEMBER, 1997
NEC America, Inc.
ページ2に含まれる内容の要旨
LIABILITY DISCLAIMER NEC America Inc. reserves the right to change the specifications, functions, or features, at any time, without notice. NEC America Inc. has prepared this document for use by its em- ployees and customers. The information contained herein is the property of NEC America Inc. and shall not be reproduced without prior written approval from NEC America Inc. term NEAX and D are registered trademarks of NEC Corporation. Copyright 1997 NEC America Inc. Printed in the U.S.A.
ページ3に含まれる内容の要旨
ADD. No. ADD. No. PAGE No. PAGE No. 001 002 003 004 005 006 007 008 001 002 003 004 005 006 007 008 i 2.2 35 2.2 ii 2.1 36 2.2 iii 37 iv 38 1 39 2.2 2 40 2.1 2.2 3 2.2 41 2.2 42.1 42 5 2.1 43 6 44 7 45 8 46 9 2.2 47 10 2.2 48 11 2.2 49 12 2.2 50 13 51 14 2.1 52 2.1 15 53 16 54 17 55 18 56 19 57 20 58 21 2.2 59 22 60 23 61 24 62 25 63 26 64 27 65 28 65-1 2.1 29 2.1 65-2 2.1 30 65-3 2.1 31 2.2 65-4 2.1 32 2.1 2.2 66 33 2.2 67 2.1 34 2.2 68 ADDENDUM-001 ADDENDUM-002 ADDENDUM-003 ADDENDUM-004 DATE J
ページ4に含まれる内容の要旨
ADD. No. ADD. No. PAGE No. PAGE No. 002 003 004 005 006 007 008 002 003 004 005 006 007 008 001 001 68-1 2.1 97 68-2 2.1 98 68-3 2.1 99 68-4 2.1 100 69 101 70 2.1 102 71 2.1 103 72 104 73 105 74 106 75 107 76 108 77 109 78 110 78-1 2.1 111 78-2 2.1 112 78-3 2.1 113 78-4 2.1 114 78-5 2.1 115 78-6 2.1 116 79 117 80 118 81 119 82 120 83 121 84 122 85 123 86 124 87 125 88 126 89 127 90 128 91 129 92 130 93 131 94 132 95 133 96 134 ADDENDUM-001 ADDENDUM-002 ADDENDUM-003 ADDENDUM-004 DATE JULY, 1998 D
ページ5に含まれる内容の要旨
ND-45504 (E) ISSUE 2 DECEMBER, 1997 NEAX2000 IVS Circuit Card Manual TABLE OF CONTENTS Page LIST OF FIGURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii LIST OF TABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv CHAPTER 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ6に含まれる内容の要旨
Page 3. LAMP INDICATIONS AND SWITCH SETTINGS OF APPLICATION CIRCUIT CARDS . . . . . . . . . . . . . 52 PN-AP00-A (AP00) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 PN-AP01 (AP01). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 PN-BRTA (BRI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ7に含まれる内容の要旨
LIST OF FIGURES Figure Title Page 3-1 Circuit Card Mounting Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3-2 MP/FP Card Mounting Slots. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3-3 MP/FP Card Mounting Slots for Back up MP System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3-4 BS00/BS01 Card Mounting Slots .
ページ8に含まれる内容の要旨
LIST OF TABLES Table Title Page 2-1 Functional Outline of Control Circuit Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2-2 Functional Outline of Application Circuit Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2-3 Functional Outline of Line/Trunk Circuit Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4-1 Table of Control Circuit Cards . . .
ページ9に含まれる内容の要旨
CHAPTER 1 INTRODUCTION 1. PURPOSE For installers and maintenance technicians of the NEAX2000 IVS (PBX), this manual explains the functional outline and installation conditions of the circuit cards, and explains the meaning of each indicator lamp (LED) and the switch settings on the circuit cards. 2. OUTLINE OF THE MANUAL This manual consists of four chapters. The contents of Chapter 2 through 4 are as outlined below. • Chapter 2: Functional Outline of Circuit Cards This chapter outlines variou
ページ10に含まれる内容の要旨
This page is for your notes. CHAPTER 1 ND-45504 (E) Page 2 Revision 2.0
ページ11に含まれる内容の要旨
CHAPTER 2 FUNCTIONAL OUTLINE OF CIRCUIT CARDS This chapter explains the functional outline of various circuit cards used in the NEAX2000 IVS. Explanations are given in alphabetical order of the circuit card names for each kind (Control, Application, and Line/Trunk) of circuit cards. 1. CONTROL CIRCUIT CARDS Table 2-1 shows the functional outline of each control circuit card. Table 2-1 Functional Outline of Control Circuit Cards FUNCTIONAL CARD NAME FUNCTIONAL OUTLINE NAME Bus interface card fo
ページ12に含まれる内容の要旨
Table 2-1 Functional Outline of Control Circuit Cards (Continued) FUNCTIONAL CARD NAME FUNCTIONAL OUTLINE NAME Main power supply card. PZ-PW86/ Input: AC100 V/200 V (50 Hz/60 Hz) PWR PZ-PW86-A Output: –27 V (8 A), +5 V (8.5 A), CR (30 mA) One card per PIM. Main power supply card. Input: AC100 V/200 V (50 Hz/60Hz) PZ-PW86(C) PWR Output: –27 V (4.5 A), +5 V (7.5 A), CR (30 mA), +80 V (110 mA) One card per PIM. Main power supply card. Input: AC100 V/200 V (50 Hz/60 Hz) PZ-PW86(D) PWR Output: –2
ページ13に含まれる内容の要旨
Table 2-2 Functional Outline of Application Circuit Cards (Continued) FUNCTIONAL CARD NAME FUNCTIONAL OUTLINE NAME Ethernet Control card. This card is used with the PN-AP01 card to accommodate the Ethernet, transmit- PN-CC01 ETHER ting/receiving a signal of TCP/IP protocol. 10 BASE-T twisted pair cable can be connected directly to this card. Phase Locked Oscillator card. This card is a phase locked oscillator for providing a synchronized clock signal PN-CK00 PLO with the network. This card is
ページ14に含まれる内容の要旨
3. LINE/TRUNK CIRCUIT CARDS Table 2-3 shows the functional outline of each line/trunk circuit card. Table 2-3 Functional Outline of Line/Trunk Circuit Cards FUNCTIONAL CARD NAME FUNCTIONAL OUTLINE NAME 2-line Amplifier Trunk card. PN-2AMPA AMP This card is equipped with the functions of Echo Canceller (EC), Automatic Gain Controller (AGC) and Tone Disabler (TD). 2-line Long-Line circuit card provided with the Power Failure Transfer (PFT) function. Line resistance in the case of a long-line c
ページ15に含まれる内容の要旨
Table 2-3 Functional Outline of Line/Trunk Circuit Cards (Continued) FUNCTIONAL CARD NAME FUNCTIONAL OUTLINE NAME term 4-line Digital Line Circuit card for D Series E/Series III/ElectraPro/DSS Con- sole. PN-4DLCA DLC [–27 V Version, 2-wire type, line length: max. 200 m (656 ft.)] This card is equipped with quick diagnostics to detect short line conditions and the normality (Synchronous/Asynchronous) of the terminal. term 4-line Digital Line Circuit card exclusively used for D Series E/Series
ページ16に含まれる内容の要旨
Table 2-3 Functional Outline of Line/Trunk Circuit Cards (Continued) FUNCTIONAL CARD NAME FUNCTIONAL OUTLINE NAME 4-line Analog Line Circuit card for single line telephones. This card provides 4 circuits with Disconnect Supervision. PN-4LCJ LC Loop resistance: Max. 600 ohms. This card is equipped with quick diagnostics to detect short and open line condi- tions. V.35 DTE interface card. PN-M03 M03 This card is used together with the PN-2DPCB card to provide the V.35 interface. 2-line OD Trunk
ページ17に含まれる内容の要旨
BUS/AP8 MP/FP/AP7 FP/AP6 LT15/AP5 LT14/AP4 LT13/AP3 LT12/AP2 LT11/AP1 LT10/AP0 LT09 LT08 LT07 LT06 LT05 LT04 LT03 LT02 LT01 LT00 CHAPTER 3 CIRCUIT CARD INSTALLATION CONDITIONS This chapter explains the conditions for installing various kinds of circuit cards used in the PBX. 1. CIRCUIT CARD MOUNTING SLOTS Figure 3-1 below shows circuit card mounting slots allocated in the PIM based on circuit card type. PIM0 - 7 PWR *1 *2 *3 *4 BUILT-IN BATTERY LT00 - LT15 : Line/trunk circuit card mounting slot
ページ18に含まれる内容の要旨
BUS/AP8 MP0 MP1 LT15/FP/AP5 LT14/AP4 LT13/AP3 LT12/AP2 LT11/AP1 LT10/AP0 LT09 LT08 LT07 LT06 LT05 LT04 LT03 LT02 LT01 LT00 PIM(H)0 PWR *1 *2 *3 BUILT-IN BATTERY LT00 - LT15 : Line/trunk circuit card mounting slots AP0 - AP8 : Application circuit card mounting slots MP0, MP1 : PN-CP02/PN-CP02-C mounting slot FP : PN-CP01 mounting slots BUS : PN-BS00-A/PN-BS00-B, PN-BS01-A/PN-BS01-B mounting slot PWR : PZ-PW86/PZ-PW86-A/PZ-PW86 (C)/(D) mounting slot *1 Either line/trunk circuit cards or applicatio
ページ19に含まれる内容の要旨
2. INSTALLATION CONDITIONS FOR CONTROL CIRCUIT CARDS 2.1 PN-CP00/PN-CP00-B/PN-CP00-C (MP) Mount the PN-CP00/PN-CP00-B/PN-CP00-C in the MP slot of PIM0. 2.2 PN-CP01 (FP) 1. The PN-CP01 is required only if any of the following is true. • More than one PIM is used. • A PN-2DLCC is used. • A PN-AP01 is used. • OAI, ACD, No. 7 CCIS or ISDN is used. 2. When the system is equipped with two PIMs, mount one PN-CP01 in the FP slot of PIM0. When the sys- tem is equipped with more than two PIMs--depending o
ページ20に含まれる内容の要旨
2.3 PN-CP02/PN-CP02-C (MP) Mount the PN-CP02/PN-CP02-C in the MP0 and MP1 slot of PIM(H)0. This card is used only for Back up MP system. PIM3 PIM7 F F PIM2 PIM6 P P PIM1 PIM5 F M M F PIM(H)0 PIM4 P P P P 1 0 Figure 3-3 MP/FP Card Mounting Slots for Back up MP System CHAPTER 3 ND-45504 (E) Page 12 Addendum-002 Revision 2.2 OCTOBER, 1998
