ページ1に含まれる内容の要旨
865GM3/865PEM2 Series
MS-6763 (v1.X) M-ATX Mainboard
Version 1.0
G52-M6763X1-G22
i
ページ2に含まれる内容の要旨
Manual Rev: 1.0 Release Date: July 2003 FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equip- ment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accor- dance with the ins
ページ3に含まれる内容の要旨
Copyright Notice The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice. Trademarks All trademarks are the properties of their respective owners. ® ® Intel and Pentium are registered trademarks of Intel Corporation. ® PS/2 and OS /2 are registe
ページ4に含まれる内容の要旨
Safety Instructions 1. Always read the safety instructions carefully. 2. Keep this User’s Manual for future reference. 3. Keep this equipment away from humidity. 4. Lay this equipment on a reliable flat surface before setting it up. 5. The openings on the enclosure are for air convection hence protects the equipment from overheating. DO NOT COVER THE OPENINGS. 6. Make sure the voltage of the power source and adjust properly 110/220V before connecting the equipment to the power inlet. 7. Place t
ページ5に含まれる内容の要旨
CONTENTS FCC-B Radio Frequency Interference Statement .......................................... iii Copyright Notice .......................................................................................... iii Revision History ........................................................................................... iii Technical Support ......................................................................................... iii Safety Instructions ..........................................
ページ6に含まれる内容の要旨
USB Connectors .......................................................................... 2-14 Audio Port Connectors ............................................................... 2-15 Connectors ......................................................................................... 2-16 Floppy Disk Drive Connector: FDD1........................................... 2-16 Chassis Intrusion Switch Connector: JCI1 (Optional) ................. 2-16 Ultra ATA HDD Connectors: IDE1, IDE2 ..............
ページ7に含まれる内容の要旨
Integrated Peripherals ........................................................................ 3-15 Power Management Setup ................................................................. 3-21 PNP/PCI Configurations ..................................................................... 3-25 PC Health Status ................................................................................ 3-27 Frequency/Voltage Control ................................................................ 3-29 Load Def
ページ8に含まれる内容の要旨
Getting Started Chapter 1. Getting Started Getting Started Thank you for choosing the 865GM3/865PEM2 Series (MS-6763 v1.X) micro ATX mainboard. The 865GM3/865PEM2 ® Series are based on Intel Springdale-G/PE & ICH5 chipsets ® for optimal system efficiency. Designed to fit the advanced Intel ® Pentium 4 processors in 478 pin package, the 865GM3/865PEM2 Series deliver a high performance and professional desktop plat- form solution. 1-1
ページ9に含まれる内容の要旨
MS-6763 M-ATX Mainboard Mainboard Specifications CPU ® Supports Intel P4 Northwood (Socket 478) processors. FSB 533~800MHz, depending on the CPU installed. Supports up to 3.2GHz. Chipset ® Intel Springdale-PE/G chipset - Supports FSB 800/533/400MHz. - Supports AGP 8X/4X interface. - Supports DDR 400/333/266 memory interface. - Integrated graphics (for Springdale-G only). ® Intel ICH5 chipset - Hi-Speed USB (USB2.0) controller, 480Mb/sec. - 2 Serial ATA/150 ports. - 2 channel Ultra ATA 100
ページ10に含まれる内容の要旨
Getting Started On-Board Peripherals On-Board Peripherals include: - 1 floppy port supports 2 FDDs with 360K, 720K, 1.2M, 1.44M and 2.88Mbytes - 2 serial ports (COM A & JCOM1) - 1 parallel port supports SPP/EPP/ECP mode - 1 VGA port (for 865GM3 Series only) - 8 USB 2.0 ports (Rear * 4/ Front * 4) - 1 Line-In/Line-Out/Mic-In port - 1 RJ45 LAN jack - 2 IEEE 1394 ports (optional for 865PEM2 Series only) Audio AC97 link controller integrated in ICH5. Software audio codec AD1981B. - Compliant with
ページ11に含まれる内容の要旨
MS-6763 M-ATX Mainboard Mainboard Layout T: Mouse B: Keyboard JCOM1 CPU_FAN JPW1 Intel 865PE T: Line-In M: Line-Out B: Mic AGP Slot PCI Slot 1 BATT + SYS_FAN JSP1 PCI Slot 2 RealTek SATA2 RTL8101L JBAT1 ICH5 SATA1 NEC JCD1 D72874GC PCI Slot 3 JCI1 Codec BIOS JAUX1 JAUD1 JUSB1 JFP1 CNR JMD1 J1394_1 JUSB2 865PEM2 Series (MS-6763 v1.X) Micro ATX Mainboard 1-4 DIMM 1 DIMM 2 DIMM 3 DIMM 4 ATX1 Winbond IDE 2 83627HF-AW IDE 1 FDD1
ページ12に含まれる内容の要旨
Getting Started T: Mouse B: Keyboard JCOM1 CPU_FAN JPW1 Intel 865G T: Line-In M: Line-Out B: Mic AGP Slot Intel PCI Slot 1 82547EI BATT + SYS_FAN JSP1 PCI Slot 2 SATA2 JBAT1 ICH5 SATA1 JCD1 JCI1 PCI Slot 3 Codec BIOS JAUX1 JUSB1 JAUD1 CNR JFP1 JUSB2 JMD1 865GM3 Series (MS-6763 v1.X) Micro ATX Mainboard 1-5 DIMM 1 DIMM 2 DIMM 3 DIMM 4 ATX1 Winbond IDE 2 83627HF-AW IDE 1 FDD1
ページ13に含まれる内容の要旨
Hardware Setup Chapter 2. Hardware Setup Hardware Setup This chapter provides you with the information about hard- ware setup procedures. While doing the installation, be careful in holding the components and follow the installation procedures. For some components, if you install in the wrong orientation, the components will not work properly. Use a grounded wrist strap before handling computer components. Static electricity may damage the components. 2-1
ページ14に含まれる内容の要旨
MS-6763 M-ATX Mainboard Quick Components Guide DDR DIMMs, p.2-7 CPU_FAN, p.2-19 CPU, p.2-3 JCOM1, p.2-11 ATX1, p.2-9 FDD1, p.2-16 Back Panel I/O, p.2-10 JPW1, p.2-9 IDE2/1, AGP1, p.2-26 p.2-17 SYS_FAN, p.2-19 SATA2/1, JSP1, p.2-20 p.2-18 JBAT1, p.2-25 JCI1, p.2-16 JCD1, p.2-20 JFP1, p.2-21 CNR1, p.2-26 JAUX1, JMD1, p.2-20 PCI 1~3, p.2-20 p.2-26 JAUD1, p.2-22 J1394_1, p.2-24 JUSB1/2, p.2-23 2-2
ページ15に含まれる内容の要旨
Hardware Setup Central Processing Unit: CPU ® ® The mainboard supports Intel Pentium 4 processors in the 478 pin package. The mainboard uses a CPU socket called PGA478 for easy CPU installation. When you are installing the CPU, make sure the CPU has a heat sink and a cooling fan attached on the top to prevent overheating. If you do not find the heat sink and cooling fan, contact your dealer to purchase and install them before turning on the computer. CPU Core Speed Derivation Procedure If CPU
ページ16に含まれる内容の要旨
MS-6763 M-ATX Mainboard CPU Installation Procedures for Socket 478 1. Please turn off the power and Open Lever unplug the power cord before installing the CPU. Sliding 90 degree Plate 2. Pull the lever sideways away from the socket. Make sure to raise the lever up to a 90-de- gree angle. Gold arrow 3. Look for the gold arrow. The gold arrow should point to- wards the lever pivot. The CPU can only fit in the cor- rect orientation. 4. If the CPU is correctly installed, the pins should be Correct
ページ17に含まれる内容の要旨
Hardware Setup Installing the CPU Fan As processor technology pushes to faster speeds and higher performance, thermal management becomes increasingly important. To dissipate heat, you need to attach the CPU cooling fan and heatsink on top of the CPU. Follow the instructions below to install the Heatsink/Fan: 1. Locate the CPU and its retention 2. Position the heatsink onto the reten- mechanism on the motherboard. tion mechanism. retention mechanism 3. Mount the fan on top of the heatsink. 4. Pre
ページ18に含まれる内容の要旨
MS-6763 M-ATX Mainboard 5. Connect the fan power cable from the mounted fan to the 3-pin fan power connector on the board. fan power cable NOTES 2-6
ページ19に含まれる内容の要旨
Hardware Setup Memory The mainboard provides four 184-pin unbuffered PC3200/PC2700/ PC2100 DDR DIMMs and supports the memory size up to 4GB. To operate properly, at least two DIMM modules must be installed onboard. DDR DIMM Slots (DIMM 1~4) Memory Speed/CPU FSB Support Matrix DDR200 DDR266 DDR333 DDR400 FSB400 V V X X FSB533 V V V X FSB800 V V V V DDR Population Rules Install at least one DIMM module on the slots. Each DIMM slot support
ページ20に含まれる内容の要旨
MS-6763 M-ATX Mainboard Please refer to the following table for detailed dual-channel DDR population rules. Other combination not listed below will function as single- channel DDR. DIMM1 (CH A) DIMM2 (CH A) DIMM3 (CH B) DIMM4 (CH B) System Density 128MB~1GB 128MB~1GB 256MB~2GB 128MB~1GB 128MB~1GB 256MB~2GB 128MB~1GB 128MB~1GB 256MB~2GB 128MB~1GB 128MB~1GB 256MB~2GB 128MB~1GB 128MB~1GB 128MB~1GB 384MB~3GB 128MB~1GB 128MB~1GB 128MB~1GB 384MB~3GB 128MB~1GB 128MB~1GB 128MB~1GB 384MB~3GB 128MB~1GB 12
