ページ1に含まれる内容の要旨
MB898/MB898F/
MB898RF
®
Socket LGA775 Pentium 4
®
Intel Q965 Chipset
Industrial Motherboard
USER’S MANUAL
Version 1.0
ページ2に含まれる内容の要旨
Acknowledgments Award is a registered trademark of Award Software International, Inc. PS/2 is a trademark of International Business Machines Corporation. Intel and Pentium 4 are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Winbond is a registered trademark of Winbond Electronics Corporation. All other product names or trademarks are properties of their respective owners.
ページ3に含まれる内容の要旨
Table of Contents Introduction ....................................................... 1 Checklist .............................................................................. 1 Product Description ............................................................. 2 Specifications ...................................................................... 3 Board Dimensions ............................................................... 4 Installations ........................................
ページ4に含まれる内容の要旨
This page is intentionally left blank. iv MB898 User’s Manual
ページ5に含まれる内容の要旨
INTRODUCTION Introduction Checklist ® Your MB898/MB898F Pentium 4 motherboard package should include the items listed below: • The MB898/MB898F motherboard • This User’s manual • 1 Back I/O shield • 1 IDE cable • 1 Floppy cable • 1 SATA cable • 1 Serial-Port cable • 1 CD containing the following: • Chipset Drivers • Flash Memory Utility MB898 User’s Manual 1
ページ6に含まれる内容の要旨
INSTALLATIONS Product Description ® The MB898/MB898F LGA 775 Pentium 4 motherboard incorporates the Intel Q965 chipset that can utilize a single LGA775 processor of up to 4.0GHz or higher and supports FSB frequency of 533/800/1066Mhz (133MHz(533MT/s), 200MHz(800MT/s) and 266MHz(1066MT/s) HCLK respectively. ® The Q965 chipset is designed for use with the Pentium 4 processor with 1M Level 2 (CPU integrated) cache. The integrated GMCH component provides the CPU interface, DDR2 inter
ページ7に含まれる内容の要旨
INTRODUCTION Specifications MB898/MB898F ® ® Socket LGA775 Pentium 4 ATX Motherboard w/ Intel Q965 Chipset Features ® ® ® Supports Intel Core 2 Duo / Pentium D / Pentium 4 HT / Celeron D processors Up to 3.8GHz+, 533MHz/800MHz/1066MHz FSB DDR2 DIMM x 4, max. 8GB ICH8 10/100 or Intel PCI Express Gigabit Ethernet ® Integrated Intel Q965 VGA, CRT support 4 x SATA II, 10 x USB 2.0, 4 x COM, Watchdog timer, Digital I/O (MB898RF supports 6 x SATA with RAID) 4 x PCI, 2 x
ページ8に含まれる内容の要旨
INSTALLATIONS Board Dimensions 4 MB898 User’s Manual
ページ9に含まれる内容の要旨
INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the MB898/MB898F in order to set up a workable system. The topics covered are: Installing the CPU ........................................................................ 6 ATX Power Installation ............................................................... 6 Installing the Memory .................................................................. 7 Setting the Jumpers .........
ページ10に含まれる内容の要旨
INSTALLATIONS Installing the CPU The MB898/MB898F motherboard supports an LGA 775 processor socket for Intel® Pentium® 4 processors. The LGA 775 processor socket comes with a lever to secure the processor. Refer to the pictures below, from left to right, on how to place the processor into the CPU socket. Please note that the cover of the LGA775 socket must always be installed during transport to avoid damage to the socket. ATX Power Installation The system power is provide
ページ11に含まれる内容の要旨
INSTALLATIONS Installing the Memory The MB886/MB898F motherboard supports four DDR2 memory sockets for a maximum total memory of 8GB in DDR memory type. It supports DDR2 533/667/800. Basically, the system memory interface has the following features: Supports two 64-bit wide DDR data channels Available bandwidth up to 6.4GB/s (DDR2 800) for single-channel mode and 12.8GB/s (DDR2 800) in dual-channel mode. Supports 256Mb, 512Mb, 1Gb DDR2 technologies. Supports only x8, x16, DDR2
ページ12に含まれる内容の要旨
INSTALLATIONS Setting the Jumpers Jumpers are used on MB898/MB898F to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on MB898/MB898F and their respective functions. Jumper Locations on MB898/MB898F .......................................... 9 JP8, JP9, JP10: RS232/422/485 (COM2) Selection ..................... 10 JP6: IDE DMA Mode
ページ13に含まれる内容の要旨
INSTALLATIONS Jumper Locations on MB898/MB898F Jumper Locations on MB898/MB898F .......................................... 9 JP8, JP9, JP10: RS232/422/485 (COM2) Selection ..................... 10 JP6: IDE DMA Mode Setting....................................................... 11 JBAT1: Clear CMOS Contents .................................................... 10 JP1: Boot Device Selection………………..……………………..11 JP5: Configure and Recovery…………………………………… 11 JP11: Processor Setting ........
ページ14に含まれる内容の要旨
INSTALLATIONS JBAT1: Clear CMOS Contents Use JBAT1, a 3-pin header, to clear the CMOS contents. Note that the ATX-power connector should be disconnected from the motherboard before clearing CMOS. JBAT1 Setting Function Pin 1-2 Normal Short/Closed Pin 2-3 Clear CMOS Short/Closed JP1: Select the Boot Device (Factory used only) JP1 Setting Boot Device Pin 1-2 SPI Short/Closed Pin 1-2 FWH (default) Open JP5: Configure and Recovery (Factory use only)
ページ15に含まれる内容の要旨
INSTALLATIONS JP6: IDE DMA Mode Setting JP6 Setting Function Pin 1-2 Master (default) Short/Closed Pin 1-2 Slave Open JP8, JP9, JP10: RS232/422/485 (COM2) Selection COM1 is fixed for RS-232 use only. COM2 is selectable for RS232, RS-422 and RS-485. COM3 and COM4 are fixed for RS-232 use only. The following table describes the jumper settings for COM2 selection. COM2 RS-232 RS-422 RS-485 Function JP10: JP10: JP10: 1-2 3-4 5-6 Jumper Setting JP9: JP9: JP
ページ16に含まれる内容の要旨
INSTALLATIONS Connectors on MB898 The connectors on MB898/MB898F allows you to connect external devices such as keyboard, floppy disk drives, hard disk drives, printers, etc. The following table lists the connectors on MB898 and their respective functions. ATX1: 24-pin ATX Power Connector ................................................. 14 ATX2: ATX 12V Power Connector .................................................... 14 MB898/MB898F Edge Connectors ..............................
ページ17に含まれる内容の要旨
INSTALLATIONS Connector Locations on MB898/MB898F ATX1: 24-pin ATX Power Connector ...................................................................................................................14 ATX2: ATX 12V Power Connector ......................................................................................................................14 MB898/MB898F Edge Connectors..............................................................................................................
ページ18に含まれる内容の要旨
INSTALLATIONS ATX1: 24-pin ATX Power Connector Signal Name Pin # Pin # Signal Name 3.3V 13 1 3.3V -12V 14 2 3.3V Ground 15 3 Ground PS-ON 16 4 +5V Ground 17 5 Ground Ground 18 6 +5V Ground 19 7 Ground -5V 20 8 Power good +5V 21 9 5VSB +5V 22 10 +12V +5V 23 11 +12V Ground 24 12 +3.3V ATX2: ATX 12V Power Connector Signal Name Pin # Pin # Signal Name +12V 5 1 Ground +12V 6 2 Ground +12V 7 3 Ground +12V 8 4 Ground MB898/MB898F Edge Connectors 14 MB898 User’s
ページ19に含まれる内容の要旨
INSTALLATIONS VGA1: VGA CRT Connector VGA1 is a DB-15 VGA connector located beside the COM1 port. The following table shows the pin-out assignments of this connector. Signal Name Pin # Pin # Signal Name Red 1 2 Green Blue 3 4 N.C. GND 5 6 GND GND 7 8 GND VCC 9 10 GND N.C. 11 12 DDCDATA HSYNC 13 14 VSYNC DDCCLK 15 CN1: Parallel Port Connector CN1 is a DB-25 external connector situated on top of the VGA and serial ports. CN1 Parallel Port Signal Name Pin # Pin
ページ20に含まれる内容の要旨
INSTALLATIONS CN2, J10, J6, J5: COM1/2/3/4 Serial Ports CN2 (COM1) is a DB-9 connector, while J10, J6 and J5 are a COM pin-header connectors. COM1 COM2 Signal Name Pin # Pin # Signal Name DCD, Data carrier detect 1 6 DSR, Data set ready RXD, Receive data 2 7 RTS, Request to send TXD, Transmit data 3 8 CTS, Clear to send DTR, Data terminal ready 4 9 RI, Ring indicator GND, ground 5 10 Not Used COM2 is jumper selectable f
