ページ1に含まれる内容の要旨
USER’S
MANUAL
PMB-531LF
Intel® Core Duo/Solo
Mini-ITX Motherboard
With VGA/Audio/LAN
PMB-531LF M3
ページ2に含まれる内容の要旨
Copyright Notice PMB-531LF Intel® Core Duo/Solo Mini-ITX Motherboard With VGA/ Sound/ LAN OPERATION MANUAL COPYRIGHT NOTICE This operation manual is meant to assist both Embedded Computer manufacturers and end users in installing and setting up the system. The information contained in this document is subject to change without any notice. This manual is copyrighted in December, 2006. You may not reproduce or transmit in any form or by any means, electronic,
ページ3に含まれる内容の要旨
Copyright Notice FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interfer
ページ4に含まれる内容の要旨
Contents TABLE OF CONTENTS CHAPTER 1 INTRODUCTION 1-1 About This Manual ........................................................ 1-2 1-2 System Specification ...................................................... 1-3 1-3 Safety Precautions ......................................................... 1-6 CHAPTER 2 HARDWARE CONFIGURATION 2-1 Jumper & Connector Quick Reference Table ................ 2-2 2-2 Component Locations ..................
ページ5に含まれる内容の要旨
Contents CHAPTER 3 SOFTWARE UTILITIES 3-1 Introduction …………..........................................…....... 3-2 3-2 VGA Driver Utility ……………………………….…… 3-3 3-3 Flash BIOS Update ..............................................…....... 3-4 3-4 LAN Driver Utility …...........................................…...... 3-6 3-5 Sound Driver Utility …………………………………… 3-7 3-6 Intel Chipset Software Installation Utility …..……..….. 3-8 3-7 USB2.0 Softw
ページ6に含まれる内容の要旨
CHAPTER 1 INTRODUCTION This chapter gives you the information for PMB-531LF. It also outlines the System specifications. Section includes: About This Manual System Specifications Safety Precautions Experienced users can skip to chapter 2 on page 2-1 for a Quick Start. Page:1-1
ページ7に含まれる内容の要旨
Chapter 1 Introduction 1-1. ABOUT THIS MANUAL Thank you for purchasing our PMB-531LF Intel® Core Duo/Solo Mainboard enhanced with VGA/Sound/LAN, which is fully PC / AT compatible. The PMB-531LF provides faster processing speed, greater expandability and can handle more tasks than before. This manual is designed to assist you how to install and set up the system. It contains four chapters. The user can apply this manual for configuration according to the following chapters:
ページ8に含まれる内容の要旨
Chapter 1 Introduction 1-2. SYSTEM SPECIFICATIONS CPU: Intel® Core Duo up to 2.33GHz. Intel® Core Solo up to 1.83GHz. Intel® Core Duo ULV up to 1.2 GHz. Intel® Core Solo ULV up to 1.2 GHz. Auto detect voltage regulator. CHIPSET: Intel® 945GM + ICH7R (FSB: 533/667MHz) MEMORY : 2 x 200-pin DDR2 SO-DIMM Support DDR II 667 SDRAM up to 2GB. CACHE : Built-in CPU. REAL-TIME CLOCK : 256-byte battery backed CMOS RAM. Hardware implementation to indicate century ro
ページ9に含まれる内容の要旨
Chapter 1 Introduction DISPLAY : Built-in Intel 945GM, support for CRT, LVDS, TV-Out. Onboard 15-pin VGA D-SUB connector, support for resolution on QXGA Monitor. IDE INTERFACE : One IDE ports support up to two IDE devices. Supports Ultra DMA 33. SERIAL ATA PORT : Two S-ATA connectors from ICH7R. USB CONNECTOR : Support up to six USB 2.0 ports. LAN ADAPTER : LAN: Intel® 82573V (10/100/1000 Mbps) Support wake-on-LAN function. SERIAL PORT : Four high speed
ページ10に含まれる内容の要旨
Chapter 1 Introduction IRDA PORT : 5-pin Infrared port, support IrDA v1.0 SIR protocol GREEN FUNCTION : Controlled by hardware and software. LED INDICATOR : System power Hard Disk access LAN LED indicator DMA CONTROLLER : 8237 x 2 DMA CHANNELS : 7 INTERRUPT CONTROLLERS : 82C59 x 2 INTERRUPT LEVELS : 15 OPERATING TEMPERATURE : 0 to 60 °C. BOARD DIMENSIONS : 170 mm x 170 mm, 6.69” x 6.69” BOARD NET WEIGHT : 810 gram. Page: 1-5 PMB-531
ページ11に含まれる内容の要旨
Chapter 1 Introduction 1-3. SAFETY PRECAUTIONS Follow the messages below to avoid your systems from damage: 1. Keep your system away from static electricity on all occasions. 2. Prevent electric shock. Don‘t touch any components of this card when the card is power-on. Always disconnect power when the system is not in use. 3. Disconnect power when you change any hardware devices. For instance, when you connect a jumper or install any cards, a surge of power may damage th
ページ12に含まれる内容の要旨
CHAPTER HARDWARE 2 CONFIGURATION ** QUICK START ** Helpful information describes the jumper & connector settings, and component locations. Section includes: Jumper & Connector Quick Reference Table Component Locations Configuration and Jumper settings Connector’s Pin Assignments Page 2-1
ページ13に含まれる内容の要旨
Chapter 2 Hardware Configuration 2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE COM Port Connector …………………………. COM1,COM2,COM3,COM4 COM3/4 Port RI/Voltage Selection …………... JP16,JP17 RS232/422/485 (COM2) Selection …………… JP15 Keyboard/Mouse Connector …………………. JKBMS1 Reset Connector ……………………………… JPANEL1 ( 13 ，15 ) Hard Disk Drive LED Connector ……………. JPANEL1 ( 09 ，11 ) Power Button ……………………………….. JPANEL1 ( 14 ，16 ) External Speaker Connector ………………… JPANEL1 ( 1 ，3，5，7 )
ページ14に含まれる内容の要旨
Chapter 2 Hardware Configuration 2-2. COMPONENT LOCATIONS PMB-531LF Connector, Jumper and Component locations Page: 2-3 PMB-531LF USER ′S MANUAL
ページ15に含まれる内容の要旨
Chapter 2 Hardware Configuration 2-3. HOW TO SET THE JUMPERS You can configure your board by setting jumpers. Jumper is consists of two or three metal pins with a plastic base mounted on the card, and by using a small plastic "cap", Also known as the jumper cap (with a metal contact inside), you are able to connect the pins. So you can set-up your hardware configuration by "open" or "close" pins. The jumper can be combined into sets that called jumper blocks. When the jump
ページ16に含まれる内容の要旨
Chapter 2 Hardware Configuration JUMPER DIAGRAMS Jumper Cap looks like this 2 pin Jumper looks like this 3 pin Jumper looks like this Jumper Block looks like this JUMPER SETTINGS 2 pin Jumper close(enabled) Looks like this 1 1 3 pin Jumper 2-3 pin close(enabled) Looks like this 1 1 Jumper Block 1-2 pin close(enabled) Looks like this 12 1 2 Page: 2-5 PMB-531LF USER ′S MANUAL
ページ17に含まれる内容の要旨
Chapter 2 Hardware Configuration 2-4. COM PORT CONNECTOR COM1 : COM1 Connector COM1 is fixed as RS-232. The pin assignment is as follows : PIN ASSIGNMENT 1 DCD1 2 RX1 3 TX1 4 DTR1 5 GND 6 DSR1 7 RTS1 8 CTS1 9 RI1 COM2 : COM2 Connector The COM2 is selectable as RS-232/422/485. The pin assignment is as follows : ASSIGNMENT PIN RS-232 RS-422 RS-485 1 DCD2 TX- TX- 2 RX2 TX+ TX+ 3 TX2 RX+ RX+ 4 DTR2 RX- RX- 5 GND GND GND 6 DSR2 RTS- NC 7 RTS2 RTS+ NC 8
ページ18に含まれる内容の要旨
Chapter 2 Hardware Configuration COM3 : COM3 Connector COM3 is fixed as RS-232. The pin assignment is as follows : PIN ASSIGNMENT 1 DCD3 2 RX3 3 TX3 4 DTR3 5 GND 6 DSR3 7 RTS3 8 CTS3 9 RI3 10 NC COM3’s pin 9 is selectable for RI, +5V or +12V. For more information, please refer to our “2-5 COM RI and Voltage Selection”. COM4 : COM4 Connector COM4 is fixed as RS-232. The pin assignment is as follows : PIN ASSIGNMENT 1 DCD4 2 RX4 3 TX4 4 DTR4 5 GND
ページ19に含まれる内容の要旨
Chapter 2 Hardware Configuration 2-5. COM3/4 RI & VOLTAGE SELECTION JP16 : COM3 RI & Voltage Selection The selections are as follows: COM JUMPER JUMPER SELECTION SETTINGS ILLUSTRATION 5V 5-6 COM3 12V 3-4 RI 1-2 ***Manufacturing Default -- RI. Page: 2-8 PMB-531LF USER ′S MANUAL
ページ20に含まれる内容の要旨
Chapter 2 Hardware Configuration JP17 : COM4 RI & Voltage Selection The selections are as follows: COM JUMPER JUMPER SELECTION SETTINGS ILLUSTRATION 5V 5-6 COM4 12V 3-4 RI 1-2 ***Manufacturing Default -- RI. Page: 2-9 PMB-531LF USER ′S MANUAL
