ページ5に含まれる内容の要旨
HS-872P User’s Manual 2.15 ...................................................................... 36 Chapter 3 ........................................... 38 3.1
ページ6に含まれる内容の要旨
HS-872P User’s Manual Introduction Chapter 1 1.1 The HS-872P is an all-in-one single board computer with PISA bus. with supporting Intel Core 2 Duo / Core Duo / Core solo / Celeron M processor for 533/667MHz front side bus, Intel 945GM and ICH7-M chipset, integrated GMA950 graphics, DDR2 SDRAM memory, Realtek AC97 Audio, Serial ATA and two Intel 82573L Gigabit LAN . Intel Yonah dual core Processor The board su
ページ7に含まれる内容の要旨
HS-872P User’s Manual Introduction 1.2 General Specification Form Factor Half-size PISA CPU card CPU Intel® Core 2 Duo/ Core Duo/ Core Solo/ Celeron M processor Package type: Micro- FCPGA478 Front side bus: 533/667MHz Memory 1 x 240-pin DDR2 400/533/667MHz SDRAM up to 2GB Unbufferred, none-ECC memory supported only Chipset Intel® 945GM and ICH7-M BIOS Phoenix-Award v6.00PG 4Mb PnP flash BIOS Green Function Power sa
ページ8に含まれる内容の要旨
HS-872P User’s Manual Introduction Type Triple speed 10/100/1000Base-T auto-switching Fast Ethernet Full duplex, IEEE802.3U compliant Connector External two RJ45 connectors with LED on rear I/O panel Solid State Disk Interface Flash Type Compact Flash Type II for Compact Flash Card or Micro Drive ISA Interface ISA Bridge Winbond W83628G & W83629G Function I/O & IRQ supported only, no support DMA & bus mastering Audio Interface Chipset REALTEK
ページ9に含まれる内容の要旨
HS-872P User’s Manual Introduction 1.3 < Mechanical Drawing > Mechanical Drawing 9
ページ10に含まれる内容の要旨
PICMG Backplane HS-872P User’s Manual Introduction 1.4 Intel Yonah Processor 1 x 240-pin DDR2 533/667MHz up to Intel GMA950 Graphics 2GB HDTV LVDS DVI 945GM 2 x SATA CompactFlash IDE AC97 ALC655 4 x USB2.0 ports ICH7-M Intel 82573L 2 x GLAN W83627THG 2 x Serial ports 1 x Parallel port 1 x Floppy port ISA Bridge 8-bit GPIO 1 x IrDA BIOS 10 Block Diagram
ページ11に含まれる内容の要旨
HS-872P User’s Manual (This Page is Left for Blank) 11
ページ12に含まれる内容の要旨
HS-872P User’s Manual Hardware Setup Chapter 2 2.1 DC_IN CN_PS SATA1/2 JFRNT FDD IDE SYSFAN DDRII_A MINIPCI CPUFAN CN_USB1/2 CN_LVDS CN_DIO CN_ATKB CN AUDIO CN_COM2 CDIN CN_LPT CN_COM1 CN_DVI CN_INV CN_IR CN_HDTV Connector Location 12
ページ13に含まれる内容の要旨
HS-872P User’s Manual Hardware Setup CF PS2 RJ45_1 RJ45_2 CRT Connector Location 13
ページ14に含まれる内容の要旨
HS-872P User’s Manual Hardware Setup 2.2 2.2.1 Connector Function Remark DDRII_A 240 –pin DDR2 SDRAM DIMM socket Standard IDE 44-pin primary IDE connector Slim FDD 26-pin floppy connector Slim S_ATA1/2 7-pin Serial ATA connector Standard DC_IN 4-pin AT power supply connector Standard CN_PS 3-pin ATX function connector Standard CN_AUDIO 5 x 2-pin audio connector Standard CDIN 4-pin CD-ROM audio input conn
ページ15に含まれる内容の要旨
HS-872P User’s Manual Hardware Setup 2.3 Jumper Function JRTC CMOS Operating/Clear Setting JVLCD LCD Panel Voltage Setting JCRT CRT attach select setting JCSEL1/2 COM2 RS232/422/485 mode setting JCRT JVLCD JCSEL1 JCSEL2 JRTC Jumper Reference 15
ページ16に含まれる内容の要旨
HS-872P User’s Manual Hardware Setup 2.4 < CPU and Memory Setup > 2.4.1 The board comes with the socket479 for Intel Core 2 Dual/Core Dual /Core solo processor, it supports new generation of Intel Core 2 Dual/Core Dual /Core solo processor with 533/667MHz of front side bus and 2MB L2 cache. Please follow the instruction to install the CPU properly. Unlock way 1. Use the flat-type Check point screw drive to unlock the CPU socket 2. F
ページ17に含まれる内容の要旨
HS-872P User’s Manual Hardware Setup 2.4.2 HS-872P has one 240-pin DDR2 DIMM support up to 2GB of memory capacity. The memory frequency supports 533/667MHz. Only Non-ECC memory is supported. Dual-Channel technology is supported while applying two same modules on one of each group. Notice: When applying 2GB of memory, due to the memory resource issue, the available memory size would be less than 2GB. DDRII_A
ページ18に含まれる内容の要旨
HS-872P User’s Manual Hardware Setup 2.5 The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values. Jumper: JRTC Type: Onboard 3-pin jumper JRTC Mode 1-2 Clear CMOS 2-3 Normal Operation Default setting JRTC 1 3 18 CMOS Setup
ページ19に含まれる内容の要旨
HS-872P User’s Manual Hardware Setup 2.6 The board has one Ultra ATA33 IDE interface to support up to 2 ATAPI devices, and one Compact Flash Type II socket on the solder side. 44 IDE 1 Enhanced IDE Interface 19
ページ20に含まれる内容の要旨
HS-872P User’s Manual Hardware Setup 2.7 Based on Intel ICH7-M, the board provides two Serial ATA interfaces with up to 150MB/s of transfer rate. SATA1/2 2.8 The Intel 82573L supports triple speed of 10/100/1000Base-T, with IEEE802.3 compliance and Wake-On-LAN supported. LAN 20 Serial ATA Interface
