ページ1に含まれる内容の要旨
PCI-6871
PCI Eden400 Half-sized SBC
with SODIMM/VGA
LCD/LVDS/LAN and CFC2
Users Manual
ページ2に含まれる内容の要旨
Copyright This document is copyrighted, © 2002. All rights are reserved. The orig- inal manufacturer reserves the right to make improvements to the prod- ucts described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmit- ted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable. However, the original manufacturer
ページ3に含まれる内容の要旨
Packing List Before you begin installing your card, please make sure that the following materials have been shipped: 1 ea. PCI-6871 all-in-one single board computer 1 ea. startup manual CD-ROM or disks for utility, drivers, and manual (in PDF format) 1 ea. power cable p/n: 1703080101 1 ea. PS/2 KB/M cable p/n: 1700060202 1 ea. Printer cable p/n:1700260250 1 ea. FDD cable p/n:1701340603 1 ea. EIDE cab
ページ4に含まれる内容の要旨
PCI-6871 Users Manual iv
ページ5に含まれる内容の要旨
Table of Contents Contents Chapter 1 General Information ........................................1 1.1 Introduction ....................................................................... 2 1.2 Features ............................................................................. 3 1.3 Specifications .................................................................... 3 1.3.1 Standard SBC Functions................................................. 3 1.3.2 VGA/LCD/LVDS Interface..................
ページ6に含まれる内容の要旨
2.19.2 Flat panel display connector (CN18)............................ 21 2.19.3 Extension flat panel connector (CN17) ........................ 21 2.19.4 LVDS LCD panel connector (CN21) ........................... 21 2.19.5 Panel type selection (S1)............................................... 22 2.20 Ethernet configuration..................................................... 22 2.20.1 100Base-T connector (CN15)....................................... 23 2.20.2 Network boot ....................
ページ7に含まれる内容の要旨
Table of Contents 5.2.1 Installation for Windows 95 ......................................... 48 5.2.2 Installation for Windows 98/Me................................... 52 5.2.3 Installation for Windows NT ........................................ 57 5.2.4 Installation for Windows 2000 ..................................... 62 5.2.5 Installation for Windows XP ........................................ 67 5.3 Further Information......................................................... 73 Chapter 6 A
ページ8に含まれる内容の要旨
C.14 CRT Display Connector (CN12)................................... 131 C.15 Flat Panel Connector (CN18)........................................ 132 C.16 Extended Flat Panel Display Connector (CN17) .......... 133 C.17 LCD Signal Mapping .................................................... 134 C.18 LVDS Connector (CN21).............................................. 135 C.19 COM Port Connector (CN19, CN20)............................ 136 C.20 CompactFlash Card Connector (CN28) ..................
ページ9に含まれる内容の要旨
1 General Information This chapter gives background information on the PCI-6871. Sections include: Introduction Features Specifications Board layout and dimensions 1 Chapter 1 General Information CHAPTER
ページ10に含まれる内容の要旨
Chapter 1 Introduction 1.1 Introduction The new PCI-6871 is a half-sized CPU card with onboard VIA Eden400 C3 EBGA fanless CPU. The VIA Eden processor uses advanced 0.13µ CMOS technology with 128KB L1 cache memory and 64KB L2 cache memory on die. This board with Eden400 CPU can operate without a fan at temperatures up to 60° C (140° F) and typically consumes under 14 Watts while supporting numerous peripherals. This SBC includes a 4X AGP controller, a PCI Ethernet interface, and 36-b
ページ11に含まれる内容の要旨
1.2 Features Embedded low power VIA Eden C3 EGBA 400MHz processor Half-sized CPU card with PCI golden finger Fanless operation at 60° C. 1 onboard RJ-45 connector supports 10/100Base-T Ethernet 4X AGP graphics for high performance applications Supports PC/104 Supports wake on LAN Supports wake on Modem Supports LCD backlight turn-off function 1.3 Specifications 1.3.1 Standard SBC Functions CPU: VIA C3 fanless EBGA 400MHz processor System chipset: VIA VT8606 "TwisterT" +V
ページ12に含まれる内容の要旨
Keyboard/mouse connector: Supports standard PC/AT keyboard and a PS/2 mouse Power management: Supports power saving modes including Nor- mal/Standby/Suspend modes. APM 1.2 compliant Watchdog timer: 62 level timer intervals USB: Four universal serial bus ports PC/104 expansion: PC/104 connector for ISA control board Solid State Disk: Supports one 50-pin socket for CFC type I/II 1.3.2 VGA/LCD/LVDS Interface Chipset: VIA TwisterT chip with integrated Savage4 2D/3D/Video Accelerator
ページ13に含まれる内容の要旨
+ PCI-6871 REV.A1 I 1.4 Board layout: dimensions Figure 1.1: Board layout: dimensions (component side) 5 Chapter 1 General Information
ページ14に含まれる内容の要旨
+ PCI-6871 REV.A1 Figure 1.2: Board layout: dimensions (solder side) PCI-6871 Users Manual 6
ページ15に含まれる内容の要旨
2 Installation This chapter explains the setup procedures of PCI-6871 hardware, including instruc- tions on setting jumpers and connecting peripherals, switches and indicators. Be sure to read all safety precautions before you begin the installation procedure. 7 Chapter 2 Installation CHAPTER
ページ16に含まれる内容の要旨
Chapter 2 Installation 2.1 Jumpers The PCI-6871 has a number of jumpers that allow you to configure your system to suit your application. The table below lists the functions of the various jumpers. Table 2.1: Jumpers Label Function JP1 CMOS clear JP2 LAN power select JP3 RS-232/422/485 select JP4 Watch-Dog output selct S1 Panel type select 2.2 Connectors On-board connectors link the PCI-6871 to external devices such as hard disk drives, a keyboard, or floppy drives. The table below li
ページ17に含まれる内容の要旨
Table 2.2: Connectors CN9 IR CON CN10 Audio I/F CN11 MAIN PWR CON CN12 D-SUB VGA CN13 HDD, PWR LED CON & WDT Output CN14 DIO CON CN15 LAN RJ45 CON CN16 PC104 CN17 LCD CON2 (10*2) CN18 LCD CON1 (20*2) CN19 COM1 CN20 COM2 CN21 LVDS CON CN23 USB3,4 CN24 LCD backlight CN25 PS/2 KB/MS CN26 EXT_KB CN27 LCD INV PWR CN28 CF CON FAN1 CPU fan power 9 Chapter 2 Installation
ページ18に含まれる内容の要旨
+ PCI-6871 REV.A1 I 2.3 Locating jumpers Figure 2.1: Jumper locations PCI-6871 Users Manual 10
ページ19に含まれる内容の要旨
+ PCI-6871 REV.A1 I 2.4 Locating Connectors Figure 2.2: Connectors (component side) 11 Chapter 2 Installation
ページ20に含まれる内容の要旨
2.5 Setting Jumpers You may configure your card to match the needs of your application by setting jumpers. A jumper is a metal bridge used to close an electric cir- cuit. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To close a jumper, you connect the pins with the clip. To open a jumper, you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3. In this case you would connect
