ページ1に含まれる内容の要旨
GE Fanuc Automation
State Logic Products
State Logic Processor
For Series 90 -30 PLC
User’s Guide
GFK-0726B March 1998
ページ2に含まれる内容の要旨
GFL–002 Warnings, Cautions, and Notes as Used in this Publication Warning Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Caution Caution notices are used where equipment might be damaged if care is not taken. No
ページ3に含まれる内容の要旨
GE Fanuc Automation North America, Inc. GFJ–317C Software License Agreement YOU SHOULD CAREFULLY READ THE FOLLOWING TERMS AND CONDITIONS BEFORE OPENING THIS PACKAGE. OPENING THIS PACKAGE SIGNI- FIES YOUR ACCEPTANCE OF THESE TERMS AND CONDITIONS. IF YOU DO NOT AGREE WITH THEM, YOU SHOULD PROMPTLY RETURN THE PACK- AGE UNOPENED ALONG WITH ANY OTHER ITEM THAT WAS INCLUDED IN THE SAME CATALOG NUMBER FOR FULL CREDIT. 4.4 The products to be licensed or sold hereunder are not intended for use in any
ページ4に含まれる内容の要旨
ページ5に含まれる内容の要旨
Preface Content of this Manual Chapter 1. State Logic Processor Description Chapter 2. Installation and Maintenance Chapter 3. Troubleshooting Chapter 4. Serial Communications Chapter 5. Specifications We Welcome Your Comments and Suggestions At GE Fanuc automation, we strive to produce quality technical documentation. After you have used this manual, please take a few moments to complete and return the Reader ’s Comment Card located on the next page. State Logic is a registered tradema
ページ6に含まれる内容の要旨
Contents Chapter 1 State Logic Processor Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Operational Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Chapter 2 Installation and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Selecting the Right Slot . . . . . . . . .
ページ7に含まれる内容の要旨
Contents ! +( , !% (! ) , ))!) , ! +( , (! ) , * * & ! (& ))&( , ! +( , $’# & ! $ )* ( &% ! +( *!&% ( % , ! +( , *& , , # , ! +( , &("$ )* ( &( *& # , ! +( , (! # &(* ))! %$ %*) &( (! ) , , ! +( , #
ページ8に含まれる内容の要旨
Contents " " " " " ! " " " " ! " GFK-0726B State Logic Processor for Series 90–30 PLC User’s Guide – March 1998 ix
ページ9に含まれる内容の要旨
restart lowapp ARestart oddapp: ARestarts for autonumbers that do not restart in each chapter. figure bi level 1, reset table_big level 1, reset chap_big level 1, reset1 Lowapp Alwbox restart evenap:A1app_big level 1, resetA figure_ap level 1, reset table_ap level 1, reset figure level 1, reset table level 1, reset these restarts oddbox reset: 1evenbox reset: 1must be in the header frame of chapter 1. a:ebx, l 1 resetA a:obx:l 1, resetA a:bigbx level 1 resetA a:ftr level 1 resetA c:ebx, l 1
ページ10に含まれる内容の要旨
1 Physical Description The SLP occupies a single slot in the Series 90-30 rack, communicating with the PLC CPU over the backplane to perform its many control functions. The SLP controls and accesses CPU I/O, register, and system data. a45085 LOCAL RACK CONFIGURATION P C S S P L U P Figure 1-1. SLP in Series 90-30 Chassis The 90-30 SLP u
ページ11に含まれる内容の要旨
1 a45127 BD OK OK CURRENTLY INSTALLED BATTERY CONNECTOR RESTART OPEN REPLACEMENT BATTERY CONNECTOR BATTERY PORTS 1 AND 2 SLP 300 Figure 1-2. Series 90-30 State Logic Processor The SLP comes with a battery to maintain memory when power is removed. This is a lithium battery which is installed as shown in the SLP drawings. When the battery reaches a low charge, this condition is reported to the PLC fault table. GFK-0726B Chapter 1 State Logic Processor Description 1-3
ページ12に含まれる内容の要旨
1 Operational Description The State Logic Processor (SLP) uses areas in the CPU memory for I/O references and Register values. The SLP and the CPU communicate this information over the PLC backplane. When a Ladder Logic control program and a State Logic control program are running at the same time, the State Logic and Ladder Logic programs should not be controlling the same outputs. The SLP cannot control an output that is being controlled by the CPU, since the 90-30 CPU always takes precedenc
ページ13に含まれる内容の要旨
Chapter 2 Installation and Maintenance section level 1 1 figure bi level 1 2 table_big level 1 This chapter describes how to install the SLP into a Series 90-30 PLC rack. There is also a section describing maintenance considerations. Selecting the Right Slot The SLP can be installed in any unused slot in the CPU rack of the Series 90-30 PLC if the following rules are followed: 1. Configuration created by Logicmaster must match the physical location of the modules. Configuration faults ar
ページ14に含まれる内容の要旨
2 Configuration Use the Logicmaster 90-30 configuration software to add the SLP to the Series 90-30 I/O configuration. This software is used to describe the modules present in the PLC racks. Rack and slot location and other features for each module are entered by com- pleting setup screens that describe the modules in a rack. Figure 2-1. From the main menu of the Logicmaster 90-30 configuration software, press I/O . The screen displays a representa
ページ15に含まれる内容の要旨
2 Battery The State Logic Processor comes with a 3 volt lithium battery (IC697ACC701) to maintain memory through a power cycle. If the battery charge becomes low, a fault is set in the fault table. These faults can be monitored by the State Logic program. To replace the battery, connect the new battery to the extra set of battery connections then disconnect the old battery. A Product Safety Data Sheet for the battery is available. Order from GE Fanuc using number GFK-0633. GFK-0726B Chapter 2
ページ16に含まれる内容の要旨
Chapter 3 Troubleshooting section level 1 1 figure bi level 1 3 table_big level 1 This chapter provides procedures for diagnosing State Logic Processor (SLP) problems. If these procedures do not solve the problem, contact the GE Fanuc Hotline (1-800-828-5747) for assistance. Status LED is not ON Steady 1. Check that power is supplied to the I/O rack housing the SLP. Try removing and reinstalling the SLP. 2. Cycle power to the SLP, then press the reset button for more than 5 seconds. 3. T
ページ17に含まれる内容の要旨
3 Communications Problems with ECLiPS or OnTOP 1. Check that the serial cable used conforms to one of the types specified for communications to the SLP ports. Check that the cable is firmly secured at both ends. 2. When there is a communications problem, a message indicating problems connecting to the controller is displayed together with some options. Select the “Change Host Comm Port Settings” option to check the computer port being used and the baud rate. The default SLP baud rate is 19.2K
ページ18に含まれる内容の要旨
Chapter 4 Serial Communications section level 1 1 figure bi level 1 4 table_big level 1 Serial communications with the State Logic Processor (SLP) is provided through one of the two serial ports. Each of these ports can send and receive serial data independent from the other. Port 1 is an RS-232 port and port 2 is an RS-422/485 port. There is only one 25-pin connector on the SLP which provides access to the connections for both ports. The SLP comes with a WYE cable which provides one
ページ19に含まれる内容の要旨
4 Programming Serial Communications The program communicates through two ports using WRITE and READ terms. For ex- ample: State: Get_Setpoint Write “Enter New Setpoint” to Operator_Panel. Read SetPoint1 from Operator_Panel, then go to Check_Setpoint State. The Write Term sends the string of characters, Enter New Setpoint, to the port defined as the Operator_Panel. This same port is then monitored for input by the Read Term in the next Statement. The variable Setpoint1 is set to the value ente
ページ20に含まれる内容の要旨
4 Serial Port Setup There are several serial port configuration options. Some of these options are set using ECLiPS or OnTOP, and others can only be set by an executing State Logic program. ECLiPS or OnTOP Options The options available in the ECLiPS or OnTOP menus to change the configuration of the SLP serial ports are displayed below. The options available in the ECLiPS or OnTOP menus to change the configuration of the SLP serial ports are displayed below.
