ページ1に含まれる内容の要旨
COM-2(PC)F
RS-232C (2ch) Serial I/O Board
User’s Guide
ページ2に含まれる内容の要旨
Copyright Copyright 1996 CONTEC Co., LTD. ALL RIGHTS RESERVED No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC Co., LTD. CONTEC Co., LTD. makes no commitment to update or keep current the information contained in this document. The information in this document is subject to change without notice. All relevant issues have been considered in the preparation of this document. Should you notice an omission or any questionable it
ページ3に含まれる内容の要旨
Product Configuration - COM-2(PC)F Board…1 - Sample Program Diskette (3.5inch/1.44MB)…1 - User's Guide (This Booklet)…1 Unpacking: This board is specially packed in an anti-static bag to prevent damage in shipping. Check the contents to make sure that you have everything listed above. If you do not have all the items, contact your distributor or CONTEC group office where you purchased. Note! Do not remove the board from its protective packaging until the computer case is open and ready for inst
ページ4に含まれる内容の要旨
Table of Contents Copyright............................................................................i Trademarks ........................................................................i Product Configuration ..................................................... ii 1. Introduction ............................................................. 1 About the COM-2(PC)F Board .....................................1 Support Software of Option..........................................1 Features.......
ページ5に含まれる内容の要旨
Mounting Method............................................................28 Connecting the External Devices...................................31 Connecting the Cable......................................................32 4. System Reference.................................................... 33 Specifications...................................................................33 Circuitry Diagrams .........................................................34 Block Diagram.........................
ページ6に含まれる内容の要旨
List of Figures Figure 3.1. Names of Board Components and Default Factory Settings ..................................................................... 23 Figure 3.2. I/O Address DIP Switch............................................ 25 Figure 3.3. Interrupt Level Settings............................................. 26 Figure 3.4. Rear Panel of IBM-PC/AT......................................... 28 Figure 3.5. Removing the Cover.................................................. 28 Figure 3.6. E
ページ7に含まれる内容の要旨
Figure 6.11.Flowchart of Sample Program 9................................ 53 Figure 6.12.Flowchart of Sample Program10 ............................... 54 Figure 6.13.Flowchart of Sample Program 11 .............................. 55 Figure 6.14. IVR Bit Function in Enhanced Mode........................ 61 Figure 6.15.Difference in Jumpers (JP1~JP3)............................... 64 vi COM-2(PC)F
ページ8に含まれる内容の要旨
List of Tables Table 2.1. COM Port Support for Various Programming Languages................................................................. 21 Table 3.1. I/O Address Settings ................................................. 25 Table 3.2. Example Compatible Mode Settings ......................... 27 Table 4.1. Specifications............................................................ 33 Table 6.1. Data Format .............................................................. 40 Table 6.2. Sw
ページ9に含まれる内容の要旨
viii COM-2(PC)F
ページ10に含まれる内容の要旨
Introduction 1. Introduction About the COM-2(PC)F Board The COM-2(PC)F is an IBM PC/AT ISA-Bus add-on interface board for multi-channel RS-232C asynchronous communications. It features two serial communication ports and a programmable communication rate ranging from 50 to 115,200 bps for communication or modem control. Support Software of Option - For Windows API-PAC(W32) - For Windows 3.1 API-SIO(PC)WIN - For MS-DOS SUPPORT-PAC(PC)103 Features - 2-channel asynchronous communication - Supports R
ページ11に含まれる内容の要旨
Introduction Limited Three-Year Warranty CONTEC Interface boards are warranted by CONTEC Co., LTD to be free from defects in material and workmanship for up to three years from the date of purchase by the original purchaser. Repair will be free of charge only when this device is returned freight prepaid with a copy of the original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office, from which it was purchased. This warranty is not applicable for scratche
ページ12に含まれる内容の要旨
Introduction About the Manual This manual consists of the following chapters : Chapter 1 Introduction Chapter 2 How to Use the Board Chapter 3 Hardware Setup Chapter 4 I/O Ports and Registers Chapter 5 System Reference Chapter 6 Troubleshooting Chapter 7 Index COM-2(PC)F 3
ページ13に含まれる内容の要旨
Introduction 4 COM-2(PC)F
ページ14に含まれる内容の要旨
How to Use the Board 2. How to Use the Board Compatible Mode and Enhanced Mode The COM-2(PC)F supports Compatible mode and Enhanced mode. In Compatible mode, the board channels operate as standard PC serial ports. In Enhanced mode, the board operates under CONTEC's proprietary control procedures. Give full consideration to the features of each mode when selecting which mode to use in your system. Compatible Mode The two channels of the COM-2(PC)F can be used as standard PC serial ports. Chann
ページ15に含まれる内容の要旨
How to Use the Board Operating under Windows Me/98 This section describes the procedure for using the board under Windows Me/98 and lists a number of points to note. Procedure When using the board under Windows Me/98, the OS must be set to recognize the I/O address and interrupt level used by the COM-2(PC)F. In Windows Me/98, this is called hardware installation. Use the following installation procedure. Check the Current Settings First, check the current settings. Check which interrupt levels
ページ16に含まれる内容の要旨
How to Use the Board Compatible Mode Installation Procedure 1 1. Set the operation mode (I/O address) and interrupt level for the COM-2(PC)F. Set the COM-2(PC)F switch and jumpers as described in Hardware Setup. Set an interrupt level that is not currently used by the computer. 2. Insert the COM-2(PC)F in an expansion slot and turn on the power to the PC. 3. After Windows Me/98 starts, select [Control Panel] from [My Computer] and start the [Add New Hardware]. 4. Click [Next >] in response to
ページ17に含まれる内容の要旨
How to Use the Board Compatible Mode Installation Procedure 2 1. Turn on the power to the PC without inserting the COM-2(PC)F in an expansion slot. 2. After Windows Me/98 starts, select [Control Panel] from [My Computer] and start the [Add New Hardware]. 3. Click [Next >] in response to [To begin installing your new hardware, click Next] in the Add New Hardware Wizard. 4. Select [No] in response to [Do you want Windows to search for your new hardware ?]. 5. Select the [Ports (COM & LPT)] folder
ページ18に含まれる内容の要旨
How to Use the Board Enhanced Mode Installation Procedure When it is used with Enhanced Mode, API-PAC(W32) of the option is necessary. Refer to Help "HWINSTE.HLP" of the way of registering the hardware being attached to API-PAC(W32) for the way of installing it. Check Resources Always check the PC resources (I/O address and interrupt level) assigned to the COM-2(PC)F before actually using the board. Use the following procedure to check the resources managed by the OS. 1. Select [System] from [
ページ19に含まれる内容の要旨
How to Use the Board Operating under Windows 95 This section describes the procedure for using the board under Windows 95 and lists a number of points to note. Procedure When using the board under Windows 95, the OS must be set to recognize the I/O address and interrupt level used by the COM-2(PC)F. In Windows 95, this is called hardware installation. Use the following installation procedure. Check the Current Settings First, check the current settings. Check which interrupt levels are availab
ページ20に含まれる内容の要旨
How to Use the Board Compatible Mode Installation Procedure 1 1. Set the operation mode (I/O address) and interrupt level for the COM-2(PC)F. Set the COM-2(PC)F switch and jumpers as described in Hardware Setup. Set an interrupt level that is not currently used by the computer. 2. Insert the COM-2(PC)F in an expansion slot and turn on the power to the PC. 3. After Windows 95 starts, select [Control Panel] from [My Computer] and start the [Add New Hardware]. 4. Click [Next >] in response to [To
