ページ1に含まれる内容の要旨
R
P2B-L / P2B-S / P2B-LS
®
Pentium II Motherboards
USER’S MANUAL
Special Features
ASUS P2B-L (power supply must provide at least 720mA on the +5VSB)
• Intel 82558 LAN Chipset
• Wake-On-LAN
ASUS P2B-S
• Adaptec 7890 SCSI Chipset
• Adaptec 3860 SCSI Transceiver
ASUS P2B-LS (power supply must provide at least 720mA on the +5VSB)
• Intel 82558 LAN Chipset
• Wake-On-LAN
• Adaptec 7890 SCSI Chipset
• Adaptec 3860 SCSI Transceiver
ページ2に含まれる内容の要旨
USER'S NOTICE No part of this manual, including the products and software described in it, may be repro- duced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup pur- poses, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”). ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED
ページ3に含まれる内容の要旨
ASUS CONTACT INFORMATION ASUSTeK COMPUTER INC. Marketing Address: 150 Li-Te Road, Peitou, Taipei, Taiwan 112 Telephone: +886-2-2894-3447 Fax: +886-2-2894-3449 Email: info@asus.com.tw Technical Support Fax: +886-2-2895-9254 BBS: +886-2-2896-4667 Email: tsd@asus.com.tw WWW: www.asus.com.tw FTP: ftp.asus.com.tw/pub/ASUS ASUS COMPUTER INTERNATIONAL Marketing Address: 6737 Mowry Avenue, Mowry Business Center, Building 2 Newark, CA 94560, USA Fax: +1-510-608-4555 Email: info-usa@asus.com.tw Technical
ページ4に含まれる内容の要旨
CONTENTS I. INTRODUCTION How this Manual is Organized ........................................................... 7 Item Checklist ..................................................................................... 7 II. FEATURES Features ............................................................................................... 8 ASUS P2B-L/P2B-S/P2B-LS Motherboard ....................................... 9 III. INSTALLATION ASUS P2B-L/P2B-S/P2B-LS Motherboard Layout ....................
ページ5に含まれる内容の要旨
CONTENTS PNP and PCI Setup ..................................................................... 52 Details of PNP and PCI Setup ............................................... 52 Load BIOS Defaults .................................................................... 54 Load Setup Defaults .................................................................... 54 Supervisor Password and User Password ................................... 55 IDE HDD Auto Detection .....................................
ページ6に含まれる内容の要旨
FCC & DOC COMPLIANCE Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provid
ページ7に含まれる内容の要旨
I. INTRODUCTION How this Manual is Organized This manual is divided into the following sections: I. Introduction Manual information and checklist II. Features Information and specifications III. Installation Instructions on setting up the motherboard. IV. BIOS Software Instructions on setting up the BIOS software V. Support Software ASUS Smart Motherboard Support CD VI. DMI Utility BIOS supported Desktop Management Interface VII. Network Interface Information on the built-in LAN controller (opt
ページ8に含まれる内容の要旨
II. FEATURES Specifications II. FEATURES Features The ASUS P2B-L/P2B-S/P2B-LS motherboards are carefully designed for the de- manding PC user who wants many advanced features processed by the fastest CPU. ® • Multi-Speed: Supports Intel Pentium II processors from 233MHz to 450MHz. • Intel AGPset: Features Intel’s 440BX AGPset with I/O subsystems and front-side bus (FSB) platform, which boosts the traditional 66-MHz internal bus speed to 100MHz. • Enhanced ACPI and Anti-Boot Virus BIOS: Featur
ページ9に含まれる内容の要旨
II. FEATURES • Wake-On-LAN Connector: Supports Wake-On–LAN activity with the optional network interface. • SB-Link™: Features Creative’s SB-Link™, allowing SB16 compatibility, us- ing Intel’s PC-PCI technology, to AWE64D or compatible PCI audio cards. • IrDA: Supports an optional infrared port module for wireless interface. • Desktop Management Interface (DMI): Supports DMI through BIOS, which allows hardware to communicate within a standard protocol creating a higher level of compatibility. (R
ページ10に含まれる内容の要旨
III. INSTALLATION Board Layout III. INSTALLATION ASUS P2B-L/P2B-S/P2B-LS Motherboard Layout Power Supply Fan TRCPU CPU_FAN Mouse (top port) PS/2 Keyboard (bottom port) USB 1 (top port) USB 2 (bottom port) USB KBPWR COM 1 BUS Freq. Intel 440BX AGPset COM 2 RJ-45 LAN Activity LED Connector Intel 82558 Ethernet LAN Controller Adaptec SCSI Accelerated Graphics Port SCSI_EN Chipset Adaptec LAN_EN AIC-3860 Chipset PCI Slot 4 SBLINK SECONDARY IDE R 1 PCI Slot 3 PRIMARY IDE Multi-I/O Intel CLRTC 1 PIIX
ページ11に含まれる内容の要旨
III. INSTALLATION Jumpers 1) CLRTC p. 13 Clear Real Time Clock (RTC) RAM 2) KBPWR p. 13 Keyboard Power Up (Enable/Disable) 3) LAN_EN p. 14 Onboard LAN Setting (Enable/Disable) 4) SCSI_EN p. 14 Onboard SCSI Setting (Enable/Disable) 5) COMBINE p. 14 IDE+SCSI LED Activity Light (Separated/Combined) 6) FS0, FS1, FS2 p. 15 CPU Bus Frequency 7) BF0, BF1, BF2, BF3 p. 15 CPU Core:Bus Frequency Multiple Expansion Slots/Sockets 1) DIMM Sockets p. 18 DIMM Memory Support 2) SEC CPU Slot p. 19 Single Edge Co
ページ12に含まれる内容の要旨
III. INSTALLATION Jumpers III. INSTALLATION Installation Steps Before using your computer, you must complete the following steps: 1. Set Jumpers on the Motherboard 2. Install System Memory Modules 3. Install the Central Processing Unit (CPU) 4. Install Expansion Cards 5. Connect Ribbon Cables, Cabinet Wires, and Power Supply 6. Setup the BIOS Software 1. Jumpers Several hardware settings are made through the use of jumper caps to connect jumper pins (JP) on the motherboard. See motherboard lay
ページ13に含まれる内容の要旨
R R III. INSTALLATION Jumper Settings 1. Clear Real Time Clock (RTC) RAM (CLRTC) The CMOS RAM is powered by the onboard button cell battery. To clear the RTC data: (1) Turn off your computer and unplug its AC power, (2) Short the two solder points labeled CLRTC, (3) Turn on your computer, (4) Hold down during bootup and enter BIOS setup to re-enter user preferences. Short the solder points to clear CMOS CLRTC P2B-L/S/LS Real Time Clock RAM (CLRTC) 2. Keyboard Power Up (KBPWR) This allo
ページ14に含まれる内容の要旨
R R R III. INSTALLATION Jumpers III. INSTALLATION 3. Onboard LAN Setting (LAN_EN) The onboard Intel 10/100 Fast Ethernet may be enabled or disabled using this jumper. LAN_EN LAN_EN 1 1 2 2 3 3 Enable Disable (Default) P2B-L/S/LS Onboard LAN Setting 4. Onboard SCSI Setting (SCSI_EN) The onboard Adaptec Fast/Wide/Ultra2 SCSI may be enabled or disabled using this jumper. SCSI_EN SCSI_EN 1 1 2 2 3 3 Enable Disable (Default) P2B-L/S/LS Onboard SCSI Setting 5. IDE/SCSI Device Activity LED Selection (
ページ15に含まれる内容の要旨
R III. INSTALLATION 6. CPU Bus Frequency (FS0, FS1, FS2) This option tells the clock generator what frequency to send to the CPU, DRAM, and chipset. This allows the selection of the CPU’s External frequency (or BUS Clock). The BUS Clock multiplied by the BUS Ratio equals the CPU’s Internal frequency (the ad- vertised CPU speed). 7. CPU Core:BUS Frequency Multiple (BF0, BF1, BF2, BF3) This option sets the frequency ratio between the Internal frequency of the CPU and the CPU’s External frequenc
ページ16に含まれる内容の要旨
(This page was intentionally left blank.) 16 ASUS P2B-L/P2B-S/P2B-LS User’s Manual
ページ17に含まれる内容の要旨
III. INSTALLATION 2. System Memory (DIMM) This motherboard uses only Dual Inline Memory Modules (DIMMs). Sockets are available for 3.3Volt (power level) unbuffered Synchronous Dynamic Random Ac- cess Memory (SDRAM). One side (with memory chips) of the DIMM takes up one row on the motherboard. To utilize the chipset’s Error Checking and Correction (ECC) feature, you must use a DIMM module with 9 chips per side (standard 8 chips/side + 1 ECC chip) and make the proper settings through “Chipset Fe
ページ18に含まれる内容の要旨
ページ19に含まれる内容の要旨
III. INSTALLATION 3. Central Processing Unit (CPU) This motherboard provides a Single Edge Contact (SEC) slot for a Pentium II pro- cessor packaged in an SEC cartridge. Pentium II Processor WARNING! Be sure that sufficient air circulation is available across the processor’s passive heatsink. Without sufficient circulation, the processor could overheat and damage both the processor and the motherboard. You may install an auxiliary fan, if necessary. You should check to see that you have the foll
ページ20に含まれる内容の要旨
III. INSTALLATION CPU III. INSTALLATION Attach Mount Bridges Four screws should be showing next to each corner of the SEC CPU Slot with the two attach mount bridges installed. SEC CPU slot NOTE: Encircled items are the screws from the mount bridges (1 & 2) Attach Mount Bridges (underside) Installing the Pentium II Processor 1. Mount the Pentium II Retention Mechanism: The retention mechanism is designed to fit into the SEC slot only one way. TIP: Orient the mechanism’s lock holes toward the m
