ページ1に含まれる内容の要旨
PowerBook (FireWire)
Memory (RAM)
Replacement Instructions
Be sure to follow these instructions carefully. Failure to follow these
instructions could result in damage to your equipment and may void your
warranty.
For this computer, you can replace memory in either the upper or lower
RAM slot. Replacing memory in your computer requires up to nine basic
steps:
• Turn off the computer.
• Open the computer.
• Remove the heat shield.
• Remove the processor module (if replacing RA
ページ2に含まれる内容の要旨
About Memory Your computer comes with a minimum of 64 megabytes (MB) of synchronous dynamic random-access memory (SDRAM) installed in a RAM slot on the bottom of the processor module. On the top of the processor module is another RAM slot you can use to add additional memory to your PowerBook. RAM Specifications The expansion slots on the top and bottom of the processor module can accept up to a 2-inch SDRAM card that meets the following specifications: • small outline-dual Inline me
ページ3に含まれる内容の要旨
Opening the Computer Warning: Always turn off your computer before opening it to avoid damaging its internal components. 1 Place your computer on a clean, flat surface. 2 Shut down your computer, remove the battery from the expansion bay, and disconnect the power adapter, modem, and any other cables connected to the computer. Warning: The internal components of your PowerBook may be hot. If you have been using your PowerBook, wait 30 minutes after shutting down your computer to let th
ページ4に含まれる内容の要旨
¨ 3 Make sure that the keyboard locking screw is not in the locked position. Your new PowerBook comes with the keyboard unlocked, so unless you or someone else locked the keyboard, you can skip this step. 4 Release the keyboard by pulling down on the keyboard release tabs (located to the left of the F1 and F9 keys) until the top portion of the keyboard pops up. 4 - PowerBook (FireWire) Memory (RAM)
ページ5に含まれる内容の要旨
5 Lift the top portion of the PowerBook keyboard up slightly near the top row of keys and pull it back far enough to release the small tabs that hold the bottom of the keyboard in place. 6 Flip the keyboard over and lay it on the palm rests. 7 Touch a metal surface inside the computer to discharge any static electricity. Important: To avoid electrostatic discharge, always ground yourself by touching a metal surface before you touch any parts or install any components inside the compu
ページ6に含まれる内容の要旨
8 With a Phillips screwdriver, remove the screws that secure the internal heat shield. Screws Heat Shield . 9 Lift up the internal heat shield. 10 At this point, • Go to the section “Replacing RAM in the Upper RAM Slot” if you are replacing RAM in the top RAM slot. • Go to the section “Replacing RAM in the Lower RAM Slot” if you are replacing RAM in the bottom RAM slot. 6 - PowerBook (FireWire) Memory (RAM)
ページ7に含まれる内容の要旨
Replacing RAM in the Upper RAM Slot 1 After opening the computer (removing the keyboard and heat shield), release the existing RAM expansion card at the two snaps so the card pops up. Then pull the expansion card out of the RAM expansion slot. Warning: When removing or installing the RAM card, do not touch its connectors. Handle the RAM card only by the edges. o 30 RAM Expansion Slot PowerBook (FireWire) Memory (RAM) - 7
ページ8に含まれる内容の要旨
2 Hold the replacement RAM expansion card at a 30-degree angle. Line up the notch in the card with the small tab in the RAM expansion slot. Then push the RAM expansion card into the expansion slot. Warning: When removing or installing the RAM card, do not touch its connectors. Handle the RAM card only by the edges. o 30 Note: You may feel some resistance. If you are having trouble inserting the card, try pushing one side at a time. 3 Gently push the RAM expansion card down until the
ページ9に含まれる内容の要旨
Replacing RAM in the Lower RAM Slot 1 After opening the computer (removing the keyboard and heat shield), remove the long screw (shown below) that secures the processor heat spreader. 2 Locate the small, plastic pull tab on the right side of the processor module and gently pull up on the tab until the processor module disconnects from the logic board. Note: The tab for the processor module is the smaller of the two plastic tabs. Processor Module Screw Pull Tab 3 Lift the processor m
ページ10に含まれる内容の要旨
5 Insert the new DIMM. RAM Slot Top of Processor Module Bottom of Processor Module Warning: When removing or installing the RAM card, do not touch its connectors. Handle the RAM card only by the edges. 6 Reinsert the processor module. (Make sure the tabs on the side of the module line up with the slots on the metal frame of the logic board. Press the tabs into the slots so the edge of the processor module is flush against the metal frame.) PowerBook (FireWire) Memory (RAM) - 10
ページ11に含まれる内容の要旨
7 Press down very firmly against the processor module until you feel it securely attach to the connector on the logic board. Then replace the screw. Note: If you have a 2-inch RAM card in the upper slot, remove it before you reinsert the processor module; the card blocks the area you need to push against to secure the processor module in place. RAM Card
Screw Processor
Module Note: If the processor module is not securely connected to the logic board, your computer will not sta
ページ12に含まれる内容の要旨
Closing the Computer 1 After replacing RAM in the upper or lower RAM slot, insert the internal heat shield. Important: When replacing the internal heat shield, make sure it does not cover the plastic tabs for the hard disk and optional AirPort Card. The plastic tab for the processor module should be placed under the heat shield. Screws Heat Shield AirPort CardTab Hard Disk Tab Processor
Module Tab 2 Press down on the bottom portion of the heat shield to secure it and then replace
ページ13に含まれる内容の要旨
4 Pull down on the keyboard release tabs (located to the left of the F1 and F9 keys) and then press down on the top portion of the keyboard. 5 Let go of the keyboard release tabs to secure the keyboard in place. 6 Replace the PowerBook battery or plug in the power adapter. Warning: Never turn on your computer unless all of its internal and external parts are in place and it is closed. Operating the computer when it is open or missing parts can damage your computer or cause injury. Po
ページ14に含まれる内容の要旨
Apple Computer, Inc. © 2000 Apple Computer, Inc. All rights reserved. Under the copyright laws, this document may not be copied, in whole or in part, without the written consent of Apple. The Apple logo is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. Use of the “keyboard” Apple logo (Option-Shift-K) for commercial purposes without the prior written consent of Apple may constitute trademark infringement and unfair competition in violation of feder
