ページ1に含まれる内容の要旨
®
MULTITASKER
MANUAL PART NUMBER: 400-0374-005
MT103-123
TWISTED PAIR RECEIVER TO
VIDEO + AUDIO CARD
USER’S GUIDE
ページ2に含まれる内容の要旨
MULTITASKER TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS................ 2 GENERAL..........................................................2 INSTALLATION..................................................2 CLEANING.........................................................2 FCC NOTICE .....................................................2 ABOUT YOUR MT103-123....................................... 3 TECHNICAL SPECIFICATIONS.............................. 3 PRODUCT DESCRIPTION ..............
ページ3に含まれる内容の要旨
MULTITASKER 1.4 FCC NOTICE PRECAUTIONS / SAFETY WARNINGS 1 Please read this manual carefully before using your • This device complies with Part 15 of the FCC MT103-123. Keep this manual handy for future Rules. Operation is subject to the following two conditions: (1) This device may not cause reference. These safety instructions are to ensure the long life of your MT103-123 and to prevent fire harmful interference, and (2) this device must and shock hazards. Please read them carefully and
ページ4に含まれる内容の要旨
MULTITASKER ABOUT YOUR MT103-123 2 TECHNICAL SPECIFICATIONS 3 Specifications are subject to change. MT103-123 See www.altinex.com for up-to-date information. TWISTED PAIR RECEIVER TO FEATURES/ VIDEO + AUDIO CARD MT103-123 DESCRIPTION The MT103-123 provides a means of receiving GENERAL computer video and audio signals over Twisted Inputs Video+Audio Pair-type (CAT-5/6) cable when used together with an ALTINEX Twisted Pair Video Transmitter such Video+Audio RJ-45 female (1) as the MT103-122 o
ページ5に含まれる内容の要旨
MULTITASKER MECHANICAL MT103-123 ELECTRICAL MT103-123 Enclosure Slots Required 1 Input Video/Sync/Audio Weight (pounds) 1.1 lb (0.5 kg) CAT-5/6 Twisted Pair ALTINEX Standard Ship Weight (pounds) 1.6 lbs (0.73 kg) Output Video Signals T° Operating 10°C-40°C RGBHV/YPbPr - Video 75 ohms T° Max 50°C RGBHV - Sync 10 kohms/TTL Humidity 90% non-condensing S-Video, Composite Video 75 ohms MTBF (calculations) 40,000 hrs Output Audio Signals Table 2. MT103-123 Mechanical Gain – Balanced at 1 kHz +6 dB +/
ページ6に含まれる内容の要旨
MULTITASKER PRODUCT DESCRIPTION 4 TOP RETAINER SCREW RGBHV/YPbPr VIDEO OUTPUT S-VIDEO INPUT C-VIDEO OUTPUT VIDEO EQUALIZATION UNBALANCED STEREO AUDIO OUTPUT BALANCED STEREO AUDIO OUTPUT 4TP INPUT BOTTOM RETAINER SCREW 400-0374-005 5
ページ7に含まれる内容の要旨
MULTITASKER APPLICATION DIAGRAMS 5 DIAGRAM 1: TYPICAL SETUP MT103-123 RGBHV/ YPbPr OR S-VIDEO OR C-VIDEO AUDIO DA1930CT 400-0374-005 6
ページ8に含まれる内容の要旨
MULTITASKER DIAGRAM 2: RJ-45 PINOUT TOP FRONT 1 8 1 8 Pin No. RJ-45 Output Signals 1 Orange/White 2 Orange 3 Green/White 4 Blue 5 Blue/White 6 Green 7 Brown/White 8 Brown Table 4 Standard 568B Wiring Color Code 400-0374-005 7
ページ9に含まれる内容の要旨
MULTITASKER DIAGRAM 3: INTERNAL VIEW INPUT OUTPUT SIGNAL POWER/ DETECT SIGNAL PRESENT RCA C-VIDEO 4-PIN CHROMA MINI DIN LUMA S-VIDEO PAIR 1 BLUE PAIR 2 RED RJ-45 15-PIN HD TWISTED PAIR VIDEO PAIR 3 GREEN RGBHV/ SYNC-ON-GREEN Y Pb Pr PAIR 4 + SYNC - HOR PROCESSING + VER - R1+ LP LP 5-PIN TB R1- AUDIO BAL. SEPARATOR STEREO L1+ LP LP AUDIO L1- RIGHT 3.5 mm UNBAL. STEREO AUDIO LEFT 400-0374-005 8
ページ10に含まれる内容の要旨
MULTITASKER DIAGRAM 4: SWITCH SETTINGS GAIN and SYNC OPTIONS POSITION DESCRIPTION The MT103-123 has an internal switch with 6 6 Video Gain ON=1 x1, OFF=x2 positions to achieve the Factory Default = x1 following features: 5 Sync-On-Green (ON/OFF) Factory Default = OFF 3,4 Vertical Sync Polarity (Positive/Negative) 3 OFF, 4 ON = Negative (Factory Default) 3 ON, 4 OFF = Positive 1,2 Horizontal Sync Polarity (Positive/Negative) 1 ON, 2 OFF = Positive (Factory Default) 1 OFF, 2 ON = Negative VIDEO
ページ11に含まれる内容の要旨
MULTITASKER INSTALLING YOUR MT103-123 6 OPERATION 7 Step 1. Determine the settings required for Gain, 7.1 RS-232 CONTROL Sync-On-Green, Horizontal Sync Polarity, The MT103-123 has many advanced and Vertical Sync Polarity. If necessary to remote-control capabilities accessible through change the factory defaults, set the standard RS-232 communication. Control may be switches per Diagram 4 on page 8. accomplished through a computer, control system, Step 2. Turn off power to the MultiTaske
ページ12に含まれる内容の要旨
MULTITASKER 7.2 DESCRIPTION OF COMMANDS COMMANDS Each command consists of three parts: 1. [VER] Function, Card ID, and Unit ID. This command displays the software version [ Function , Card ID , Unit ID ] and card type for the MT103-123 card. Example: [VERC3U2] Command Format: [VERCn] VER = Function Cn = Card ID (n = slot # from 1 to max slots) C3 = Card ID or Group ID Example: U2 = Unit ID (optional for Unit ID 0) An MT103-123 card is in slot 4. Send the For Function, see a detailed explan
ページ13に含まれる内容の要旨
MULTITASKER Example: All status feedback is enclosed in brackets, “[ ]“. Each data field within the status is enclosed in Save the status by sending the command [C4S]. parentheses. The first two characters identify The feedback returned will be similar to the the status type. The last three characters are the following: card’s ID. ON, EQ=0 C04 [SAVED] MT103-123 = Card model number FEEDBACK COMMANDS VR690-0197-005 = Firmware version The next four commands are a function of both ON = Outpu
ページ14に含まれる内容の要旨
MULTITASKER 7. [STA0] Example: ADJUST EQUALIZATION This command disables automatic feedback Continuing from the previous example, the from the card and front panel. The command equalization function is now active and may be affects any card with auto-feedback capability, adjusted using the [+] and [-] commands. The not just the MT103-123 card. The default at card will display the new equalization setting power on or reset is STA0, OFF. after each [+] or [-] command. Send the following comm
ページ15に含まれる内容の要旨
MULTITASKER 14. […S] – Save ID COMMANDS This command will save the configuration The default card ID is the same as the card slot command being sent in memory. When sending number. The next several commands allow the the command [EQ=10C4S], after reset or user to change the card ID to a value other than the power-up, the equalization level on C4 will be slot number. Once the ID is changed, moving the set to 10. card to another slot will not change the card ID. If a card in slot 4 is
ページ16に含まれる内容の要旨
MULTITASKER 18. [SIDn] Example: This command sets all the cards installed in the There are two 20-slot enclosures to be MultiTasker system to the same card ID. After connected together during normal operation. sending this command, all cards will be The first unit will use the default IDs where the addressed with the same ID. Use caution when card ID is equal to the slot number. The second sending this command to a system with multiple unit will have the same unit ID, but each card ID boar
ページ17に含まれる内容の要旨
MULTITASKER 25. [RMG] GROUP COMMANDS This command deletes one or all groups. Group commands allow several cards with the same functions to be controlled simultaneously with Command Format: [RMGk] a single command. Up to 8 groups (G1-G8) may be Gk = Group ID (k = # from 1-8, * for all) defined. These commands apply to all cards, not only the MT103-123. Example: 23. [WR] Remove all cards from G52 by sending [RMG5]. The system will return the following feedback: This command adds cards to
ページ18に含まれる内容の要旨
MULTITASKER 7.3 SUMMARY OF COMMANDS 7.4 MENU MODE Card Commands Menu Mode commands allow virtually the same functionality as programming commands. Unlike 1) [VER] Display firmware revision the programming commands in the previous 2) [C] Display card status sections, menu commands prompt the user to select from a list of available options. The system 3) [CnS] Save card settings then responds based upon selections made by the 4) [?] Display system cards user. 5) [?C] Display card informat
ページ19に含まれる内容の要旨
MULTITASKER 7.4.2 USING MENU MODE 7.4.3 MENU TYPES Do NOT press any keys except those relating to 1. MAIN MENU the current menu. If you press the ENTER key The first menu displayed after selecting the after entering a letter or digit, the original list of card is the Main Menu. This menu provides access to the key functions related to the systems will be displayed. card. Press the key representing the menu 1. In order to enter Menu Mode, the system item for access and a sub-menu will appe
ページ20に含まれる内容の要旨
MULTITASKER 4: HELP 2. Clear the card. This selection displays a list of commands Starting from the Main Menu, select the available for the MT103-123 along with a MT103-123 card and set it to the factory brief description. It is equivalent to the defaults. Follow the keystrokes below. [HELP] command. 1 Select CONTROL Menu ESC 1 Select CLEAR This selection returns you to the parent 1 Select YES to clear the card menu with the listing of all cards. ESC Return to the Main Menu 7.4.5 MENU MODE E
