ページ1に含まれる内容の要旨
SanDisk CompactFlash Memory Card
OEM Product Manual
Version 12.0
Document No. 20-10-00038
02/2007
SanDisk Corporation
Corporate Headquarters
601 McCarthy Boulevard
Milpitas, CA 95035
(408) 801-1000 Phone
(408) 801-8657 Fax
www.sandisk.com
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
SanDisk CompactFlash Card OEM Product Manual SanDisk® Corporation general policy does not recommend the use of its products in life support applications where in a failure or malfunction of the product may directly threaten life or injury. Per SanDisk Terms and Conditions of Sale, the user of SanDisk products in life support applications assumes all risk of such use and indemnifies SanDisk against all damages. Security safeguards, by their nature, are capable of circumvention. SanDisk cannot,
ページ4に含まれる内容の要旨
SanDisk CompactFlash Card OEM Product Manual –This page intentionally left blank– 02/07, Rev. 12.0 ii © 2007 SanDisk Corporation
ページ5に含まれる内容の要旨
Table of Contents CHAPTER 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 CompactFlash Standard . . . . . . . . . . . . . . . . . . . .
ページ6に含まれる内容の要旨
Table of Contents SanDisk CompactFlash Card OEM Product Manual Memory Mapped Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3 True IDE Mode Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4 ATA Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4 CHAPTER 5 ATA Command Description . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 ATA Command Set. . . . . . . . . . . . . . . . . . . . . .
ページ7に含まれる内容の要旨
CHAPTER 1 Introduction 1.1 General Description SanDisk CompactFlash® Memory Card products provide high capacity solid-state flash memory that electrically complies with the Personal Computer Memory Card International Association ATA (PC Card ATA) standard. (In Japan, the applicable standards group is JEIDA.) The CompactFlash Memory Card Series also supports a True IDE Mode that is electrically compatible with an IDE disk drive. The original CF form factor card can be used in any system th
ページ8に含まれる内容の要旨
Introduction SanDisk CompactFlash Card OEM Product Manual 1.2 Features SanDisk CompactFlash Memory cards provide the following system features: • Up to 16 GB of mass storage data • PC Card ATA protocol compatible • True IDE Mode compatible • Very low CMOS power • Very high performance • Very rugged • Low weight • Noiseless • Low Profile • +5 Volts or +3.3 Volts operation • Automatic error correction and retry capabilities • Supports power down commands and sleep modes • Non-volatile
ページ9に含まれる内容の要旨
SanDisk CompactFlash Card OEM Product Manual Introduction 1.5 PCMCIA Standard SanDisk CompactFlash Memory cards are fully electrically compatible with the PCMCIA specifications listed below: • PCMCIA PC Card Standard, 7.0, February 1999 • PCMCIA PC Card ATA Specification, 7.0, February 1999 These specifications may be obtained from: PCMCIA 2635 N. First Street, Suite 209 San Jose, CA 95131 USA Phone: 408-433-2273 Fax: 408-433-9558 1.6 Related Documentation ATA operation is governed by th
ページ10に含まれる内容の要旨
Introduction SanDisk CompactFlash Card OEM Product Manual 1.7.1 Technology Independence The 512-byte sector size of the CompactFlash Memory Card is the same as that in an IDE magnetic disk drive. To write or read a sector (or multiple sectors), the host computer software simply issues a Read or Write command to the card. This command contains the address and the number of sectors to write/read. The host software then waits for the command to complete. The host software does not get involv
ページ11に含まれる内容の要旨
SanDisk CompactFlash Card OEM Product Manual Introduction 1.7.5 Automatic Sleep Mode A unique feature of the SanDisk CompactFlash Memory Card is automatic entrance and exit from sleep mode. Upon completion of a command, the card will enter sleep mode to conserve power if no further commands are received within 5 msec. The host does not have to take any action for this to occur. In most systems, the CompactFlash Memory Card is in sleep mode except when the host is accessing it, thus conserv
ページ12に含まれる内容の要旨
Introduction SanDisk CompactFlash Card OEM Product Manual –This page intentionally left blank– 02/07, Rev. 12.0 1-6 © 2007 SanDisk Corporation
ページ13に含まれる内容の要旨
CHAPTER 2 Product Specifications For all the following specifications, values are defined at ambient temperature and nominal supply voltage unless otherwise stated. 2.1 System Environmental Specifications Table 2-1 contains environmental specifications which include temperature, humidity, acoustic noise, vibration, shock and altitude. Table 2-1 Environmental Specifications CompactFlash CompactFlash Extreme III Operating: ° C to 70° C -25° C to 85° C 0 Temperature Non-operating: -25°
ページ14に含まれる内容の要旨
Product Specifications SanDisk CompactFlash Card OEM Product Manual Sleep mode currently is specified under the condition that all card inputs are static CMOS levels and in a "Not Busy" operating state. Table 2-2 Power Requirements DC Input Voltage (Vcc) 100 mV max. ripple (p-p) 3.3V +/- 5% 5V +/- 10% a CompactFlash Memory Card Memory Subsystem Sleep Up to 512 MB 300 µ 500 µ 1.0 GB 600 µ 800 µ Over 1.0 GB 1 mA 1.2 mA Read 50 mA 55 mA Write 65 mA 70 mA Read/Write Peak 100 mA 100 mA a
ページ15に含まれる内容の要旨
SanDisk CompactFlash Card OEM Product Manual Product Specifications 2.3 System Performance All performance timings assume the CompactFlash Memory Card Series controller is in the default (i.e., fastest) mode. Table 2-3 Performance CompactFlash Memory Card Start-up Times Sleep to Write 2.5 ms maximum Sleep to Read 20 ms maximum Reset to Ready 50 ms typical; 400 ms maximum Programmable Active to Sleep Delay 20.0 MB/sec burst Data Transfer Rate To/From Flash 16.0 MB/sec burst Data Tr
ページ16に含まれる内容の要旨
Product Specifications SanDisk CompactFlash Card OEM Product Manual 2.4 System Reliability Table 2-4 Reliability >1,000,000 hours MTBF (@ 25 C) None Preventative Maintenance 14 <1 non-recoverable error in 10 bits read Data Reliability 20 <1 erroneous correction in 10 bits read 2.5 Physical Specifications Refer to Table 2-5 and see Figure 2-1 for CompactFlash Memory Card physical specifications and dimensions. Table 2-5 CompactFlash Physical Dimensions 11.4 g (.40 oz) typical, 14.2
ページ17に含まれる内容の要旨
SanDisk CompactFlash Card OEM Product Manual Product Specifications Figure 2-1 CompactFlash Memory Card Dimensions © 2007 SanDisk Corporation 2-5 Rev. 12.0, 02/07
ページ18に含まれる内容の要旨
Product Specifications SanDisk CompactFlash Card OEM Product Manual –This page intentionally left blank– 02/07, Rev. 12.0 2-6 © 2007 SanDisk Corporation
ページ19に含まれる内容の要旨
CHAPTER 3 Interface Description 3.1 Physical Description The host connects to SanDisk CompactFlash Memory cards using a standard 50-pin connector consisting of two rows of 25 female contacts each on 50 mil (1.27 mm) centers. 3.1.1 Pin Assignments and Types The signal/pin assignments are listed in Table 3-1. Low active signals have a "-" prefix. Pin types are Input, Output or Input/Output. Sections 3.3.1 and 3.3.2 define the DC characteristics for all input and output type structures.. Ta
ページ20に含まれる内容の要旨
Interface Description SanDisk CompactFlash Card OEM Product Manual PC Card I/O Pin Assignments are contained in Table 3-2. Table 3-2 PC Card I/O Mode Pin Assignments Signal Signal Pin No. Name Pin Type I/O Type Pin No. Name Pin Type I/O Type 1 GND – Ground 26 -CD1 O Ground 2 D03 I/O I1Z,OZ3 27 D11 I/O I1Z,OZ3 3 D04 I/O I1Z,OZ3 28 D12 I/O I1Z,OZ3 4 D05 I/O I1Z,OZ3 29 D13 I/O I1Z,OZ3 5 D06 I/O I1Z,OZ3 30 D14 I/O I1Z,OZ3 6 D07 I/O I1Z,OZ3 31 D15 I/O I1Z,OZ3 7 -CE1 I I3U 32 -CE2 I I3U 8 A
