ページ1に含まれる内容の要旨
Heavy-Duty Double Air Filter
MODEL G9956
INSTRUCTION MANUAL
COPYRIGHT © APRIL, 2004 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#6008 PRINTED IN TAIWAN
ページ2に含まれる内容の要旨
WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonry products. • Arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often yo
ページ3に含まれる内容の要旨
Table of Contents SECTION 1: SAFETY ....................................................................................................................... 2 Safety Instructions for Power Tools ........................................................................................... 2 Additional Safety for Double Air Filters ...................................................................................... 4 SECTION 2: GENERAL INFORMATION ...................................................
ページ4に含まれる内容の要旨
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measu
ページ5に含まれる内容の要旨
Safety Instructions for Power Tools 9. USE PROPER EXTENSION CORD. Make 15. USE RECOMMENDED ACCESSORIES. sure your extension cord is in good condi- Consult the instruction manual for recom- tion. Conductor size should be in accor- mended accessories. The use of improper dance with the chart below. The amperage accessories may cause risk of injury. rating should be listed on the motor or tool nameplate. An undersized cord will cause 16. REDUCE THE RISK OF UNINTENTIONAL a drop in line voltage r
ページ6に含まれる内容の要旨
Additional Safety for Double Air Filters 6. ALWAYS OPERATE THE MACHINE WITH 1. THIS DOUBLE AIR FILTER IS TO BE THE FILTER IN PLACE. When the filter is USED FOR WOOD DUST COLLECTION removed, the impeller is exposed to the unfil- ONLY. DO NOT use this machine to filter tered opening. toxic fumes or paint spray. DO NOT use this machine to dissipate smoke or fumes. 7. WHEN EMPTYING DUST FROM THE COL- LECTION BAGS, wear a respirator and 2. UNPLUG MACHINE BEFORE REMOVING safety glasses. Empt
ページ7に含まれる内容の要旨
SECTION 2: GENERAL INFORMATION Contact Info If you do not read this entire manual before If you have any comments or criticisms that you operating the machine, feel we should address in our next printing, please you will greatly increase write to us at: your chances of serious personal injury. To pro- Grizzly Industrial, Inc. C tect yourself, read and ⁄O Technical Documentation understand this entire P.O. Box 2069 manual! Bellingham, WA 98227 Most importantly, we stand behind our machin
ページ8に含まれる内容の要旨
SECTION 3: CIRCUIT REQUIREMENTS Grounding 110V Operation In the event of an electrical short, grounding reduces the risk of electric shock by providing a path of least resistance to disperse electric current. This tool is equipped with a power cord that has a plug with an equipment-grounding prong. The outlet must be properly installed and Serious personal injury could occur if you grounded in accordance with all local codes and connect the machine to the power source ordinances. before
ページ9に含まれる内容の要旨
SECTION 4: SET UP Inventory This machine presents serious injury hazards After all the parts have been removed from the to untrained users. Read carton, you should have: through this entire man- ual to become familiar A. Double Air Filter ......................................... 1 with the controls and B. Remote Control .......................................... 1 operations BEFORE C. Hardware Bag ............................................ 1 starting the machine! A Wear safety glasses
ページ10に含まれる内容の要旨
is diminished. The following is a list of things to Site Planning keep in mind when determining the placement of the air filter: Site planning is an important step to maximize the • Study your shop layout to determine the best effectiveness of the double air filter. Air circulation location for the double air filter. Air flow that is must be thought out and all obstructions in the air obstructed will cause a short cycle effect pro- path considered. ducing unsatisfactory results. There mu
ページ11に含まれる内容の要旨
Filter Capacity • The double air filter must be supported by joists when hanging. These joists should be capable of supporting at least 150 lbs. DO The G9956 Heavy-Duty Double Air Filter is NOT attach the double air filter to sheet rock, designed to recirculate the entire volume of air press board or paneling. These cannot sup- in a 20' x 20' x 8' room approximately 26 times port the filter and it may fall. in one hour. For the best filtering effect, the vol- ume in a room should be rec
ページ12に含まれる内容の要旨
1. If the joists are covered by sheet rock, press Hanging the Filter board, paneling or other covering, use a stud finder to locate them, and mark their cen- ters. Hardware Needed (not included) Qty Chain, rated 150 lbs. or higher ...................varies 1 2. Pre-drill /4" pilot holes into the marks on Connecting link .................................................. 8 the joists. This will make threading the lag 5 Lag eye bolts /16" x 3" or 4" ............................... 4 eyebolt
ページ13に含まれる内容の要旨
SECTION 5: OPERATIONS Operating this equipment creates the poten- tial for flying debris to cause eye injury. Always wear safety glasses when operating equipment. Everyday glasses or reading glasses only have impact resistant lenses, they are not safety glasses. Be certain the safety glasses you wear meet the appro- priate standards of the American National Standards Institute (ANSI). Figure 6. The air filter control panel. For remote control ON/OFF use: 1. Connect power to the double air
ページ14に含まれる内容の要旨
Speeds and Timer To set the fan timer: 1. Press the ON/HR button after setting the fan You can adjust the fan speed and the length of speed. time your double air filter runs by programing it —If some or all of the lights in the upper row with the included remote controller. To toggle come on, press the ON/HR button again. between fan speed and timer control functions, press the ON/HR button. 2. Increase the amount of time the fan runs before automatically shutting off by pressing To se
ページ15に含まれる内容の要旨
SECTION 6: MAINTENANCE Cleaning the Filters To avoid personal injury, disconnect power to air In order to maintain optimal operation, the filters filter when performing in the double air filter should be checked, cleaned any adjustments, clean- and/or replaced regularly depending on usage. ing or maintenance. Checking the filters once a week in a small home shop is a good habit. Checking them once a day during heavy use is important. Always wear a respirator when checking the filters.
ページ16に含まれる内容の要旨
SECTION 7: REFERENCE INFO The following pages contain the parts list, Aftermarket parts breakdown diagram, wiring diagram, and the Warranty/Return information for the Model Accessories G9956. If you have any comments regarding this manual, Grizzly carries a complete selection of fine acces- please write to Grizzly at the address below: sories for all of its equipment. Below is a list of useful replacement filters and accessories. Grizzly Industrial, Inc. C /O Technical Documentation • H
ページ17に含まれる内容の要旨
G9956 Parts Breakdown G9956 -15- Heavy-Duty Hanging Air Filter G9956 Heavy-Duty Double Air Filter -15- SPEED HOUR CONTINUE 2 4 6 8 ON/HR OFF 4 29 30 1 3 13 8 38 2 37 5 36 18 20 23 17 19 31 22 40 39 12 9 8 15 16 32 33 24 6 10 14 34 41 45 43 44 35 7 21 10 25 26 11 42 27 28 MODEL G9956 HEAVY DUTY HANGING AIR FILTER SPECIFICATIONS FAILURE TO FOLLOW THESE WARNINGS WILL RESULT IN SERIOUS PERSONAL INJURY: MOTOR: 13 ⁄ HP, 110V 1.W TO HO IS D H D A U N S G TI N OG N L AY IR . FILTER IS TO BE USED FOR
ページ18に含まれる内容の要旨
G9956 Parts List REF PART # DESCRIPTION 1 H2452 REAR FILTER 2 H2451 INNER FILTER 3 P9956003 BODY 4 P9956004 EYE BOLT 1/4-20 x 7/8 5 P9956005 HANDLE 6 P9956006 OUTLET COVER 7 PSB30 CAP SCREW 5/16-18 x 1/2 8 PS07M PHLP HD SCR M4-.7 x 8 9 P9956009 SAFETY SCREEN 10 P9956010 OUTLET PORT 11 PS01 PHLP HD SCR 10-24 x 1/2 12 P9956012 SWITCH COVER 13 P9956013 REMOTE RECEIVER 14 PWRCRD110L PWR CORD 110V, LONG W/PLUG 15 P9956015 SWITCH 16 P9956016 CIRCUIT BREAKER 3AMP 17
ページ19に含まれる内容の要旨
G9956 Wire Diagram Disconnect power from machine before performing any electrical service. Failure to do this will result in a shock hazard leading to injury or death. Pull Chain Ground Power Cord Switch Neutral Pin Plug 110 Volts for Receiver Breaker/Reset Main Switch Connections for Spade Plug Remote Control for Receiver Receiver Made Here Ground SH CAPACITOR WV 250 ACV CAP 20 MFD Run Capacitor Please use the component diagrams to help with identification.The main switch and breaker/r
ページ20に含まれる内容の要旨
Warranty and Returns Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any par- ticular purpose, are hereby limited to
