ページ1に含まれる内容の要旨
SATA II-150 PCI
Quick Installation Guide
Introducing the SATA II-150 PCI
The SATA II-150 PCI is an ultra high-speed dual channel
Serial ATA Generation 2 controller for use in PCI enabled
systems.
Features and Benefits
• Add up to two high-speed SATA hard drives
New Serial ATA cable – easier to install & provides
better air circulation
Supports two SATA channels and data transfer rate
up to 1.5Gb/s (150MB/s)
Supports Native Command Queuing (NCQ) and
SATA TCQ commands
Onboard bus master
ページ2に含まれる内容の要旨
System Requirements ® Pentium or equivalent PC with an available PCI slot ® Windows 2000 / XP (32-/64-bit) / Server 2003 & 2008 (32-/64-bit) / Vista (32-/64-bit) Package Contents SATA II-150 PCI SATA data cable and power cable Spare low profile bracket Driver CD and this quick installation guide Layout HDD LED pins (Front chassis LED; connects vertically) Internal connectors HDD Activity LED Figure 1. SATA II-150 PCI Board Layout 2
ページ3に含まれる内容の要旨
Hardware Installation Note: For low profile systems, replace the currently mounted bracket with the included low profile bracket. General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer case for a few secon
ページ4に含まれる内容の要旨
Driver Installation This section provides information on how to install the SATA II-150 PCI drivers for the following operating systems. Windows 2000 New Windows 2000 Installation A new installation of Windows 2000 requires a floppy disk for the driver installation. To make this floppy disk, copy the contents of the Floppy folder, found on the driver CD, onto a blank floppy disk then follow the directions below. 1. Install the board and follow the Microsoft procedures to install Windows 2000 ac
ページ5に含まれる内容の要旨
5. Click Yes, then click Finish. 6. Restart Windows to complete the driver installation. Windows XP/Server 2003 New Windows XP/Server 2003 Installation A new installation of Windows XP/Server 2003 requires a floppy disk for the driver installation. To make this floppy disk, copy the contents of the Floppy folder, found on the driver CD, onto a blank floppy disk then follow the directions below. 1. Install the board and follow the Microsoft procedures to install Windows accordingly. 2. Restart y
ページ6に含まれる内容の要旨
3. Insert the driver CD, select Install the software automatically (Recommended), then click Next, Next. 4. Click Continue Anyway, then click Finish. 5. Restart Windows to complete the driver installation. To Verify Windows 2000/XP/2003 Installation 1. Right click My Computer and click Manage. 2. Select Device Manager. 3. Double click SCSI and RAID Controllers, then double click Initio inic1620 S-ATA Adapter. 4. A message This device is working properly is displayed, the driver has been correctl
ページ7に含まれる内容の要旨
Existing Windows Vista Installation 1. Install the board and boot up Windows. 2. At the Found New Hardware Wizard, insert the driver CD, select Locate and install driver software (Recommended), then click Continue. 3. Click Next, select Install this driver anyway, then click Close. 4. Remove the driver CD and restart Windows to complete the installation. Windows Vista (64-bit) New Windows Vista Installation 1. Install the board and follow Microsoft procedures to install Windows accordingly. 2. A
ページ8に含まれる内容の要旨
4. Remove the driver CD and restart Windows to complete the installation. To Verify Windows Vista Installation 1. Right click Computer, click Manage, click Continue. 2. Select Device Manager. 3. Double click SCSI and RAID Controllers, then double click Initio inic1620 S-ATA Adapter. 4. A message This device is working properly is displayed, the driver has been correctly installed. Windows Server 2008 (32-bit) New Windows 2008 Installation 1. Install the board and follow Microsoft procedures to i
ページ9に含まれる内容の要旨
4. Click Browse my computer for driver software (Advanced). 5. Type in D:\Vista32, (change D: to match your CD-ROM drive letter), then click Next. 6. Click Install this driver software anyway, then click Close. 7. Remove the driver CD and restart Windows to complete the installation. Windows Server 2008 (64-bit) New Windows 2008 Installation 1. Install the board and follow Microsoft procedures to install Windows accordingly. 2. At Where do you want to install Windows?, click Load Driver. 3. Inse
ページ10に含まれる内容の要旨
Existing Windows 2008 Installation 1. Install the board and boot up Windows. 2. At the Found New Hardware Wizard, insert the driver CD, select Locate and install driver software (Recommended), then click Don't search online. 3. Click I don't have the disc. Show me other options. 4. Click Browse my computer for driver software (Advanced). 5. Type in D:\Vista64, (change D: to match your CD-ROM drive letter), then click Next. 6. Click Install this driver software anyway, then click Close. 7. Remo
ページ11に含まれる内容の要旨
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analysts will promptly respond. SIIG offers a lifetime manufacturer warranty with this product. Please see our web site for more warranty details. If you enco
ページ12に含まれる内容の要旨
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), networking, sound cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty. High-quality control standards are evident by