ページ1に含まれる内容の要旨
USB 2.0+1394 DV Kit
Quick Installation Guide
Introducing the USB 2.0+1394 DV Kit
The USB 2.0+1394 DV Kit is a complete DV editing kit --
a combo card with USB 2.0 and FireWire (1394a) interfaces,
deluxe DV editing software (full DV, AVI, QuickTime,
Windows Media, RealNetworks, and MPEG2 support)
and a 1394 6-pin/4-pin DV cable.
Features and Benefits
• Combo card design adds four USB 2.0 (480 Mbps)
and three 1394a (400 Mbps) ports into your system.
• Hot-swapping feature allows you to connect/
di
ページ2に含まれる内容の要旨
• IEEE 1394-1995, P1394a (rev. 1.1) and OHCI Interface Specification 1.0 compliant • Supports serial bus data transfer rates of 100, 200 and 400 Mbps System Requirements • Pentium or equivalent computer with an available PCI slot • Windows 98SE/ME • Windows 2000 (with SP 3) or later • Windows XP (with SP 1) or later • Windows Server 2003 Recommended system for DV capturing editing: • Pentium III or above • 128 MB RAM and CD-ROM drive • 4 GB of available hard disk space • Windows 98SE or later
ページ3に含まれる内容の要旨
Board Layout 1394 Port 1394 Ports USB 2.0 Port Power Connector USB 2.0 (optional) Ports Figure 1. Board Layout Note: This power connector (same as the one used with your floppy disk drive) is designed to provide additional power to the board when needed. This connection is optional. We recommend to connect this power connector when the following conditions occur: - All ports are used. - Device(s) not being detected. In case you need to connect this power connector, power off your system f
ページ4に含まれる内容の要旨
Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer’s case for a few seconds. Avoid any contact with internal parts and handle cards only by their external edges. 1. Turn OFF the p
ページ5に含まれる内容の要旨
3. Click Start, then Run. Type in X:\setup.exe and click OK. (Change X: to match your CD-ROM drive letter) 4. Click Next, Next, at the Warning box click OK, then click Finish to restart. 5. When the VIA ...Universal Host Controller is detected, click Next. 6. Choose Search for the best driver... and click Next. 7. Clear all check boxes, click Next, Next, Next. NOTE: If prompted for Windows 98SE Installation CD, click OK. Insert this CD and click OK. 8. Click Finish. 9. When the VIA ...Univer
ページ6に含まれる内容の要旨
3. Click Start, then Run. Type X:\setup.exe and click OK. (Change X: to match your CD-ROM drive letter). 4. Follow the on-screen instructions to install the driver. When prompted click Finish to restart. 5. At the Add New Hardware Wizard, choose Automatic search for a better ..., click Next, then click Finish. 6. Click Yes to restart Windows to complete. Windows 2000 Windows 2000 Service Pack 3 (SP 3) or later is required for this installation. If you have have Windows 2000 Service Pack 4 (SP
ページ7に含まれる内容の要旨
8. When Windows restarts, the drivers will install automatically. Windows XP/Server 2003 Windows XP Service Pack 1 (SP 1) or later is required for this installation. Windows XP Service Pack 1 or later will automatically detect and install the correct drivers for this board. Windows 2003 Server will automatically detect and install the correct drivers for this board. To Verify Successful Driver Installation 1. Check Device Manager to verify successful driver installation. Windows 98SE/ME: From th
ページ8に含まれる内容の要旨
b) Under the 1394 Bus Controller or IEEE 1394 Bus host controllers: - VIA OHCI Compliant IEEE 1394 Host Controller Windows 2000 (with SP4 or later): a) Under the Universal Serial Bus Controllers: - VIA ... Universal Host Controller - VIA ... Universal Host Controller - VIA USB Enhanced Host Controller - USB 2.0 Root Hub - USB Root Hub - USB Root Hub b) Under the IEEE 1394 Bus host controllers: - VIA OHCI Compliant IEEE 1394 Host Controller Windows XP (with SP1 or later)/Server 20
ページ9に含まれる内容の要旨
Ulead VideoStudio Software Installation ® TM The USB 2.0 + 1394 DV Kit includes Ulead VideoStudio digital video editing software for producing home videos complete with attractive titles, transitions and sounds. Before installing VideoStudio, make sure your adapter and DV camcorder are properly installed and configured. See next section, Connecting DV Camcorder, for more details on how to properly install your DV camcorder. 1. Insert the Ulead VideoStudio DV software CD. Auto- run should start
ページ10に含まれる内容の要旨
To Verify Successful DV Camcorder Setup 1. Check Device Manager to verify successful driver installation. Windows 98SE/ME: From the main desktop, right click My Computer, then click Properties. Click Device Manager tab. Windows 2000/XP/2003: Right click My Computer, click Manage, then click Device Manager. 2. Double click Imaging Device(s). - A Microsoft DV Camera and VCR or DVCamcorder should be displayed. 10
ページ11に含まれる内容の要旨
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our website at www.siig.com and click on Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and one of our technical support analysts will promptly respond. This product comes with a lifetime manufacturer warranty. Please see SIIG website for more warranty details. If you s
ページ12に含まれる内容の要旨
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), Networking, Sound Cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty. High-quality control standards are evident by
