ページ1に含まれる内容の要旨
Product Manual
®
Momentus Thin
7200-RPM
ST model # - Part # ST model # - Part #
Standard models SED model
ST320LT007 - 9ZV142 ST320LT014 - 9YK142
ST250LT007 - 9ZV14C ST250LT014 - 9YK14C
ST160LT007 - 9ZV14D ST160LT014 - 9YK14D
Free-Fall Sensor models SED (FIPS 140-2) models
ST320LT011 - 9ZVG42 ST320LT009 - 9WC142
ST250LT011 - 9ZVG4C ST250LT009 - 9WC14C
ST160LT011 - 9ZVG4D ST160LT009 - 9WC14D
Gen-2
100625253
Rev. C
January 2011
ページ2に含まれる内容の要旨
Revision history Revision Date Sheets affected or comments Rev. A 06/02/10 Initial release. Rev. B 06/24/10 fc, 2, 4, 6, 21 & 26-28. Rev. C 01/04/11 5, 8, 15 & 20. © 2011 Seagate Technology LLC. All rights reserved. Publication number: 100625253, Rev. C January 2011 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Momentus and SeaTools are either trademarks or registered trademarks of Seagate Technol
ページ3に含まれる内容の要旨
Contents 1.0 Seagate Technology support services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ4に含まれる内容の要旨
ii Momentus Thin Product Manual, Rev. C Gen-2
ページ5に含まれる内容の要旨
List of Figures Figure 1. Typical +5V only startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Figure 2. Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 3. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Figure 4. Mounting dimensions (for FIPS 140-2 models) — top, side and e
ページ6に含まれる内容の要旨
ページ7に含まれる内容の要旨
1.0 Seagate Technology support services SEAGATE ONLINE SUPPORT and SERVICES For information regarding products and services, visit http://www.seagate.com/www/en-us/about/contact_us/ Available services include: Presales & Technical support Global Support Services telephone numbers & business hours Authorized Service Centers For information regarding Warranty Support, visit http://www.seagate.com/www/en-us/support/warranty_&_returns_assistance For information regarding Data Recovery Services,
ページ8に含まれる内容の要旨
2.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® Momentus Thin model drives: ST model # Part # ST model # Part # ST model # Part # ST model # Part # Standard models Standard SED models SED (FIPS 140-2) models Free-Fall Sensor models ST320LT007 9ZV142 ST320LT014 9YK142 ST320LT009 9WC142 ST320LT011 9ZVG42 ST250LT007 9ZV14C ST250LT014 9YK14C ST250LT009 9WC14C ST250LT011 9ZVG4C ST160LT007 9ZV14D ST160LT014 9YK14D ST160LT009 9
ページ9に含まれる内容の要旨
Momentus Thin Self-Encrypting Drive models have the following additional features: • Automatic data encryption/decryption • Controlled access • Random number generator • Drive locking • 16 independent data bands • Cryptographic erase of user data for a drive that will be repurposed or scrapped • Authenticated firmware download There is no significant performance difference between Self-Encrypting Drive and standard (non-Self-Encrypt- ing Drive) models. 2.1 About the Serial ATA interface The Seri
ページ10に含まれる内容の要旨
3.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate all models. 3.1 Specification summary table The specifications listed in this table are for quick reference. For details on specification measurement or defi- nition, see the appropriate section of this manual Table 1: Drive specifications ST320LT007 - 9ZV142 ST250
ページ11に含まれる内容の要旨
Table 1: Drive specifications ST320LT007 - 9ZV142 ST250LT007 - 9ZV14C ST160LT007 - 9ZV14D ST320LT009 - 9WC142 ST250LT009 - 9WC14C ST160LT009 - 9WC14D ST320LT011 - 9ZVG42 ST250LT011 - 9ZVG4C ST160LT011 - 9ZVG4D Drive specification ST320LT014 - 9YK142 ST250LT014 - 9YK14C ST160LT014 - 9YK14D Read/write power (typical) Read: 1.6W; Write: 1.9W Idle mode, low power (typical) 0.66W Standby/Sleep mode (typical) 0.15W *** Voltage tolerance (including noise) +5V ± 10% Ambient temperature 0° to 60°C (op
ページ12に含まれる内容の要旨
3.2 Formatted capacity Formatted capacity* Guaranteed logical blocks (LBA) - 512 emulation Bytes per physical sector ST320LT007 - 9ZV142 ST320LT009 - 9WC142 625,142,448 ST320LT011 - 9ZVG42 ST320LT014 - 9YK142 ST250LT007 - 9ZV14C ST250LT009 - 9WC14C 488,397,168 4096 ST250LT011 - 9ZVG4C ST250LT014 - 9YK14C ST160LT007 - 9ZV14D ST160LT009 - 9WC14D 312,581,808 ST160LT011 - 9ZVG4D ST160LT014 - 9YK14D *One GB equals one billion bytes when referring to hard drive capacity. Accessible capacit
ページ13に含まれる内容の要旨
3.5 Recording and interface technology 4K sector models Interface Serial ATA (SATA) Recording method Perpendicular Recording density BPI (bits/in avg) 1397k Track density TPI (tracks/in avg) 315k 2 Areal density (Gb/in avg) 425 Spindle speed (RPM) (± 0.2%) 7200 Maximum Internal transfer rate (Mb/s) 1247 I/O data-transfer rate (Gb/s max) 3.0 Interleave 1:1 Cache buffer 16 MB (16,384 KB) 3.6 Physical characteristics Drive specification Height (mm) 6.8 +/-0.2 (in) 0.268 +/-0.0079 Width (mm) 69.8
ページ14に含まれる内容の要旨
3.8 Start/stop times Time to ready Typical Max @ 25°C Power-on to Ready (sec) 3.5 4.0 Standby to Ready (sec) 3.0 3.0 3.9 Power specifications The drive receives DC power (+5V) through a native SATA power connector. 3.9.1 Power consumption Power requirements for the drives are listed in the table on page 8. Typical power measurements are based on an average of drives tested, under nominal conditions, at 25°C ambient temperature. These power measure- ments are done with Interface Power Management
ページ15に含まれる内容の要旨
power to operational levels. **Standby power is measured at steady state (after 200ms from transition) Momentus Thin Product Manual, Rev. C Gen-2 9
ページ16に含まれる内容の要旨
3.9.1.1 Typical current profile Figure 1. Typical +5V only startup and operation current profile 3.9.2 Deferred spinup Momentus Thin drives do not support the deferred spinup option. If you require this option, refer to the Momen- tus 5400.3 SATA Blade Server family of drives. 3.9.3 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a maximum of 1
ページ17に含まれる内容の要旨
3.9.5 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program. The drive features the following power-management modes: Table 4: Power management modes Power modes Heads Spindle Buffer Active (operating) Tracking Rotating Full power Idle, performance Tracking Rotating Self refresh—low power Idle, active Floating Rotating Self refresh—low power Idle, low power
ページ18に含まれる内容の要旨
3.10 Environmental specifications 3.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Above 1000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. Operating: 0° to 60°C (32° to 140°F) Nonoperating: –40° to 70°C (–40° to 158°F) 3.10.2 Temperature gradient Operating 20°C per hour (68°F per hour max), without condensation Nonoperating 35°C per hour (95°F per hour max), without conde
ページ19に含まれる内容の要旨
3.10.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 3.10.5.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 350 Gs based on half-sine shock pulses of 2ms. Shocks should not be repeated more than two times per second. 3.10.5.2 Nonoperating shock The nonoperating shock level t
ページ20に含まれる内容の要旨
3.11 Acoustics Drive emission of sound is measured consistent with the ECMA-74 and its’ referenced standards. Testing is conducted at room temperature (approximately 25°C). Emission levels are reported as the total A-weighted sound power levels for steady state, idle, and active seek modes of operation. Table 5: Drive A-weighted Sound Power Levels (SWL, BA) Idle* Performance seek 2.3 bels (typ) 2.5 bels (typ) 2.5 bels (max) 2.7 bels (max) *During periods of drive idle, some offline activity m
