ページ1に含まれる内容の要旨
Product Manual
®
Momentus 5400.3
ST9160821A
ST9120822A
ST9100828A
ST980815A
ST960815A
ST940815A
100398876
Rev. C
August 2007
ページ2に含まれる内容の要旨
©2004-2007, Seagate Technology LLC All rights reserved. Publication number: 100398876, Rev. C August 2007 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Momentus, Seagate- SeaBOARD, SeaFONE, SeaTDD, and SeaTools are either trademarks or registered trade- marks of Seagate Technology LLC or one of its affiliated companies in the United States and/ or other countries. All other trademarks or registere
ページ3に含まれる内容の要旨
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.2 Formatted capacity . . . . . . . . . . . . . . . . . .
ページ4に含まれる内容の要旨
ii Momentus 5400.3 PATA Product Manual, Rev. C
ページ5に含まれる内容の要旨
List of Figures Figure 1. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Figure 2. Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 3. Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Momentus 5400.3 PATA Product Manual, Rev. C iii
ページ6に含まれる内容の要旨
iv Momentus 5400.3 PATA Product Manual, Rev. C
ページ7に含まれる内容の要旨
1.0 Introduction ® This manual describes the functional, mechanical and interface specifications for the following Seagate ® Momentus 5400.3 drives: � ST9160821A � ST9120822A � ST9100828A � ST980815A � ST960815A � ST940815A These drives provide the following key features: � 5,400-RPM spindle speed. � 8-Mbyte buffer. � Quiet operation. Fluid Dynamic Bearing (FDB) motor. � High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5. � Tunneling Magnetoresist
ページ8に含まれる内容の要旨
2 Momentus 5400.3 PATA Product Manual, Rev. C
ページ9に含まれる内容の要旨
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST9160821A, ST9120822A, ST9100828A, ST980815A, ST960815A, and ST940815A model drives. 2.1 Specification summary The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of
ページ10に含まれる内容の要旨
Table 1: Specifications for 160 and 120 Gbyte models Drive specification ST9160821A ST9120822A Seek power (typical) 2.0 watts Read/write power (typical) Read: 2.0 watts; Write: 1.8 watts Idle mode (typical, low power) 0.8 watts Standby mode 0.2 watts (typical)*** Sleep mode 0.2 watts (typical)*** Voltage tolerance (including noise) 5V ± 5% Ambient temperature 0° to 60°C (operating), –40° to 70°C (nonoperating) Temperature gradient 20°C (operating) (°C per hour max, noncondensing) 30°C (nonoper
ページ11に含まれる内容の要旨
Table 1: Specifications for 100 and 80 Gbyte models Drive specification ST9100828A ST980815A Formatted Gbytes (512 bytes/sector)* 100 80 Guaranteed sectors 195,371,568 156,301,488 Bytes per sector 512 Physical read/write heads 3 2 Discs 2 1 Cache (Mbytes) 8 Recording density, BPI (bits/inch typical) 835k Track density, TPI (tracks/inch typical) 150k 2 Areal density (Gbits/inch max) 132 Spindle speed (RPM) 5,400 Internal data transfer rate (Mbits/sec max) 352 I/O data-transfer rate (Mbytes/sec m
ページ12に含まれる内容の要旨
Table 1: Specifications for 100 and 80 Gbyte models Drive specification ST9100828A ST980815A Shock, nonoperating (Gs max at 1 msec) 900 Shock, nonoperating (Gs max at 0.5 msec) 400 Vibration, operating 1.0 Gs (0 to peak, 5–500 Hz) (max displacement may apply below 10 hz) Vibration, nonoperating 5.0 Gs (0 to peak, 5–500 Hz) (max displacement may apply below 22 hz) Drive acoustics, sound power (bels), 2 disc 2.4 (typical) Idle** 2.6 (max) 2.9 (typical) Performance seek 3.1 (max) 14 Nonre
ページ13に含まれる内容の要旨
Table 1: Specifications for 60 and 40 Gbyte models Drive specification ST960815A ST940815A Formatted Gbytes (512 bytes/sector)* 60 40 Guaranteed sectors 117,410,240 78,140,160 Bytes per sector 512 Physical read/write heads 2 1 Discs 1 Cache (Mbytes) 8 Recording density, BPI (bits/inch typical) 835k Track density, TPI (tracks/inch typical) 150k 2 Areal density (Gbits/inch max) 132 Spindle speed (RPM) 5,400 Internal data transfer rate (Mbits/sec max) 352 I/O data-transfer rate (Mbytes/sec max) 10
ページ14に含まれる内容の要旨
Table 1: Specifications for 60 and 40 Gbyte models Drive specification ST960815A ST940815A Shock, nonoperating (Gs max at 1 msec) 900 Shock, nonoperating (Gs max at 0.5 msec) 400 Vibration, operating 1.0 Gs (0 to peak, 5–500 Hz) (max displacement may apply below 10 hz) Vibration, nonoperating 5.0 Gs (0 to peak, 5–500 Hz) (max displacement may apply below 22 hz) Drive acoustics, sound power (bels), 2 disc 2.4 (typical) Idle** 2.6 (max) 2.9 (typical) Performance seek 3.1 (max) 14 Nonreco
ページ15に含まれる内容の要旨
2.2 Formatted capacity Model Formatted capacity* Guaranteed sectors Bytes per sector ST9160821A 160 Gbytes 312,581,808 512 ST9120822A 120 Gbytes 234,441,648 512 ST9100828A 100 Gbytes 195,371,568 512 ST980815A 80 Gbytes 156,301,488 512 ST960815A 60 Gbytes 117,410,240 512 ST940815A 40 Gbytes 78,140,160 512 *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.3 Default logical geometry Cyli
ページ16に含まれる内容の要旨
2.5 Recording and interface technology Technology Specification Interface Parallel ATA Recording method Perpendicular Recording density BPI (bits/inch typical) 835k Track density TPI (tracks/inch typical) 150k 2 Areal density (Gbits/inch max) 132 Spindle speed (RPM) (± 0.2%) 5,400 Internal data-transfer rate OD (Mbits/sec max) 352 I/O data-transfer rate (Mbytes/sec max) 100 (Ultra DMA mode 5) Interleave 1:1 Cache buffer 8 Mbytes (8,192 kbytes) 2.6 Physical characteristics Height (mm) 9.5 +/–
ページ17に含まれる内容の要旨
2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications below are defined as follows: � Track-to-track seek time is an average of all possible single-track seeks in both directions. � Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead. Typical seek times (msec)* Read Write Track-to-track 1.0 1.5 Average 11.0 13.0
ページ18に含まれる内容の要旨
2.9 Power specifications The drive receives DC power (+5V) through the interface connector. 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 12. Typical power measurements are based on an average of drives tested, under nominal conditions, at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed. � Seek mode During seek mode, the read/write actuator arm moves
ページ19に含まれる内容の要旨
2.9.1.1 Typical current profile Figure 4. Typical 5V startup and operation current profile 2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 10 MHz. Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. 2.9.3 Volt
ページ20に含まれる内容の要旨
2.9.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program. The drive features the following power-management modes: Table 3: Power management modes Power modes Heads Spindle Buffer Active (operating) Tracking Rotating Full power Idle, performance Tracking Rotating Self refresh—low power Idle, active Floating Rotating Self refresh—low power Idle, low power
