ページ1に含まれる内容の要旨
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Medalist XE Family
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
275xe, 545xe
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ATA Interface Drives
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .
Installation Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ2に含まれる内容の要旨
Contents Read before you begin... . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ST3660A free installation software. . . . . . . . . . . . . . . . . . . . 2 Quick software transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installing the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Configuring the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Attaching cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ3に含まれる内容の要旨
Medalist XE Family Installation Guide, Rev. A 1 Read before you begin... ® Application. Your Seagate drive is designed for NRTL-listed personal computers. It uses the ATA interface. Warning. Turn off the computer before you open the case, touch any internal components or install the drive. Static discharge. Your drive and computer contain components that can be damaged by static discharge. Static electricity is generated from the friction of two contributors rubbing together. The charge is stor
ページ4に含まれる内容の要旨
2 Medalist XE Family Installation Guide, Rev. A Maintenance and repair. Seagate drives do not require mainte- nance. The head/disc assembly is factory-sealed; a broken seal voids the warranty. Seagate customer service centers are the only facilities authorized to repair Seagate drives. Seagate does not sanction any third-party repair facilities. Note. Throughout this manual, the Medalist 275xe is referred to by its model number, ST3295A, and the Medalist 545xe is referred to by its model number
ページ5に含まれる内容の要旨
Medalist XE Family Installation Guide, Rev. A 3 4-pin power connector 2-pin header Circuit board 1 2 3 4 – +5V +5V return + +12V return +12V Drive activity Pin 1 LED (optional) 40-pin ATA interface connector 8-pin master/slave jumper block Spare jumper 7 5 3 1 across pin 1 and pin 3 Front 3-pin 8 6 4 2 power connector (optional) The drive is a master; the slave is either a Keyway 1 2 3 Medalist family drive or another ATA-compatible Ground Circuit drive, or there is no
ページ6に含まれる内容の要旨
4 Medalist XE Family Installation Guide, Rev. A Installing the drive 1. Turn the computer off. Warning. Installing or removing the drive or adapter cards while the computer is powered on can damage your drive, adapter and computer. 2. Remove the computer’s cover. Caution. Special training or tools may be required to service laptop computers. Removing the cover may void your warranty. Review the terms and conditions of your warranty before removing the cover. 3. Ground yourself. Configuring the
ページ7に含まれる内容の要旨
Medalist XE Family Installation Guide, Rev. A 5 Attaching cables Refer to Figure 1 on page 3 for the locations of the connectors. 1. Connect the remote LED (optional). 2. Attach the power cable. Attach one of the cables from the power supply to the power connector on the drive. Caution. The cable and connector are designed to mate. Do not force a connection. Improper alignment may damage your drive. 3. Attach the interface cable. The edge-stripe on the interface cable for the drive is used to
ページ8に含まれる内容の要旨
6 Medalist XE Family Installation Guide, Rev. A Installing drives in computers that use cable-select: If your computer uses the cable-select method, refer to your computer reference guide to determine which cable connector or drive slot denotes the master drive and which the slave. Mounting the drive Your Seagate drive is designed to fit into a 3.5-inch bay. You can mount the drive securely in the computer in any orientation using either the side mounting holes or the bottom mounting holes. Posi
ページ9に含まれる内容の要旨
Medalist XE Family Installation Guide, Rev. A 7 Configuring the computer Your computer maintains records representing the hardware in the system. This representation includes the translation geometry that is used by the BIOS to map the drive surface and that is stored in CMOS memory. During the boot cycle, a test is run comparing the record to the hardware. When you install a new drive, you must update this record to include a representation of the new drive. This is done in your computer’s Syst
ページ10に含まれる内容の要旨
8 Medalist XE Family Installation Guide, Rev. A Standard installation 1. Turn the computer on. 2. Enter the System Setup routine. (Refer to your computer user’s guide. System Setup may be called Setup, BIOS Setup or CMOS Setup.) If your computer uses an automatic setup utility, see the caution below. 3. Find the hard disc configuration in the System Setup screen. 4. Select a drive type that matches the drive translation geometry for your drive as shown in the following table. Translation geomet
ページ11に含まれる内容の要旨
Medalist XE Family Installation Guide, Rev. A 9 1,057 – 1,024 = 33, or 17.3 Mbytes. To avoid this problem, configure your System Setup manually. If none of the standard drive types offered in System Setup match the translation geometry of your Seagate drive, select the user-defined or custom drive type, if available, and enter your drive’s translation geometry. If your System Setup routine does not offer a user-defined drive type, select a standard drive type with a capacity that approximates, b
ページ12に含まれる内容の要旨
10 Medalist XE Family Installation Guide, Rev. A Partitioning You must partition the drive into one or more logical drives before you can use it. Caution. Partitioning or formatting a drive at any level erases all data on it. Before you repartition or reformat your drive, make a backup of your existing files on another disc or media. Seagate assumes no liability if you erase your data. You can partition a drive as follows: 1. Insert a bootable DOS diskette and boot the computer. 2. At the prompt
ページ13に含まれる内容の要旨
Medalist XE Family Installation Guide, Rev. A 11 drive: designates the drive you are formatting. Type c: if you are formatting the boot drive or if your system contains only one drive. Type d: to format a second drive. /v tells the computer you want to label the drive after it is formatted. Labeling the drive can prevent someone from ac- cidentally deleting the partition and losing your data. /s tells the computer to make the drive bootable and copy the necessary system files to the drive. 2. Wh
ページ14に含まれる内容の要旨
12 Medalist XE Family Installation Guide, Rev. A 4. Select drive type 2 for your new ST3660A. If your computer does not offer drive type 2, use the following values: 615 cylinders, 4 heads and 17 sectors. Note. These are interim drive type values that allow you to access the drive for extracting the installation files. 5. Activate the prompt for the ST3660A drive. 6. Type seamove. This command transfers the files from the ST3660A to the diskette in Drive A. When the transfer is complete, the fil
ページ15に含まれる内容の要旨
Medalist XE Family Installation Guide, Rev. A 13 EZ-Drive is easy and safe to use and versatile. If you already have a drive installed, EZ-Drive will not alter its format and files unless you instruct it to override the partition and format. You can choose a fully automatic installation that establishes one partition and quick formats the drive or a custom installation that lets you set multiple partitions of equal size (see page 15 for instruction on creating multiple partitions of unequal size
ページ16に含まれる内容の要旨
14 Medalist XE Family Installation Guide, Rev. A 2. Type ez. 3. Disregard the Notice dialog box. The EZ-Drive software is authorized for installation only with the drive on which it is shipped. Press ENTER to continue. 4. Locate the bottom box on the screen. The model number of each drive EZ-Drive identifies is listed in this box. If a drive is missing or the order is incorrect or there is a drive not identified message, make sure the master and slave jumpers are set correctly on the drives and
ページ17に含まれる内容の要旨
Medalist XE Family Installation Guide, Rev. A 15 Booting with a diskette after EZ-Drive is installed To boot your computer with a diskette: 1. Boot the computer with the diskette-drive door open. 2. Press the CTRL key when the following message appears near the end of the boot sequence: Hold the CTRL key down to boot from a floppy 3. Insert the boot diskette. The computer boots to the diskette drive. Installing multiple partitions The custom installation option in the installation menu allows
ページ18に含まれる内容の要旨
16 Medalist XE Family Installation Guide, Rev. A The computer will reboot when the partitioning process is com- plete. However, you must make sure the EZ-Drive installed drive is present to continue with the format. (The EZ-Drive banner appears when the drive is recognized.) 1. Open the diskette-drive door when you reboot. Press the CTRL key when the following message appears: Hold the CTRL key down to boot from a floppy The message is very quick and you may need to boot several times before you
ページ19に含まれる内容の要旨
Medalist XE Family Installation Guide, Rev. A 17 You can re-establish the 32-bit disk access capability using the SETUP program on the EZ-Drive diskette as follows: 1. Load Windows. 2. Open the Program Manager menu and select File. 3. Select Run. 4. Load the EZ-Drive diskette. 5. In the command line box, type drive:Setup. 6. Select Install Driver. This loads the MH32BIT.386 replace- ment driver designed to work with EZ-Drive. 7. Select Restart Windows.
ページ20に含まれる内容の要旨
18 Medalist XE Family Installation Guide, Rev. A Basic troubleshooting Warning. Always turn off the computer before changing jumpers or unplugging cables and cards. Caution. Your drive and computer contain static-sensitive de- vices. Wear a ground strap or take other antistatic precaution while handling your drive. If you have installed your drive and it does not function properly, perform the following basic checks. • Verify compatibility. Verify that the host adapter and the drive are appropri
