ページ1に含まれる内容の要旨
Product Manual
Cheetah 15K.6 SAS
ST3450856SS ST3450056SS (FDE)
ST3300656SS ST3300056SS (FDE)
ST3146356SS ST3146756SS (FDE)
100466193
Rev. B
September 2008
ページ2に含まれる内容の要旨
©2008, Seagate Technology LLC All rights reserved. Publication number: 100466193, Rev. B September 2008 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Cheetah, SeaTools and SeaTDD are either trademarks or reg- istered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/ or other countries. All other trademarks or registered trademarks are the property o
ページ3に含まれる内容の要旨
Contents 1.0 Scope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Standards, compliance and reference documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1.1 Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . .
ページ4に含まれる内容の要旨
6.4.2 Relative humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 6.4.3 Effective altitude (sea level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 6.4.4 Shock and vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 6.4.5 Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 6.4.6 Air
ページ5に含まれる内容の要旨
1.0 Scope ® ® This manual describes Seagate Technology LLC, Cheetah SAS (Serial Attached SCSI) disk drives. Cheetah 15K.6 drives support the SAS Protocol specifications to the extent described in this manual. The SAS Interface Manual (part number 100293071) describes the general SAS characteristics of Cheetah 15K.6 and other Seagate SAS drives. Model Number Full Disk Encryption (FDE) ST3450856SS No ST3300656SS No ST3146356SS No ST3450056SS Yes ST3300056SS Yes ST3146756SS Yes Cheetah 15K.6 SAS
ページ6に含まれる内容の要旨
2 Cheetah 15K.6 SAS Product Manual, Rev. B
ページ7に含まれる内容の要旨
2.0 Standards, compliance and reference documents The drive has been developed as a system peripheral to the highest standards of design and construction. The drive depends on its host equipment to provide adequate power and environment for optimum performance and compliance with applicable industry and governmental regulations. Special attention must be given in the areas of safety, power distribution, shielding, audible noise control, and temperature regulation. In particular, the drive mu
ページ8に含まれる内容の要旨
2.2 Compliance 2.2.1 Electromagnetic compliance Seagate uses an independent laboratory to confirm compliance with the directives/standards for CE Marking and C-Tick Marking. The drive was tested in a representative system for typical applications. The selected sys- tem represents the most popular characteristics for test platforms. The system configurations include: � Typical current use microprocessor � Keyboard � Monitor/display �Printer �Mouse Although the test system with this Seagate model
ページ9に含まれる内容の要旨
Seagate also has internal systems in place to ensure ongoing compliance with the RoHS Directive and all laws and regulations which restrict chemical content in electronic products. These systems include standard operat- ing procedures that ensure that restricted substances are not utilized in our manufacturing operations, labora- tory analytical validation testing, and an internal auditing process to ensure that all standard operating procedures are complied with. 2.4 Reference documents SCSI
ページ10に含まれる内容の要旨
6 Cheetah 15K.6 SAS Product Manual, Rev. B
ページ11に含まれる内容の要旨
3.0 General description Cheetah 15K.6 drives provide high performance, high capacity data storage for a variety of systems including engineering workstations, network servers, mainframes, and supercomputers. The Serial Attached SCSI inter- face is designed to meet next-generation computing demands for performance, scalability, flexibility and high- density storage requirements. Cheetah 15K.6 drives support the Serial Attached SCSI Protocol as described in the ANSI specifications, this document
ページ12に含まれる内容の要旨
3.1 Standard features Cheetah 15K.6 drives have the following standard features: � 1.5 / 3 Gbit Serial Attached SCSI (SAS) interface � Integrated dual port SAS controller supporting the SCSI protocol � Support for SAS expanders and fanout adapters � Firmware downloadable using the SAS interface � 128 - deep task set (queue) � Supports up to 32 initiators � Jumperless configuration. � User-selectable logical block size (512, 520, or 528 bytes per logical block) � Programmable logical block reallo
ページ13に含まれる内容の要旨
3.4 Reliability � 1,600,000 hour MTBF (Annualized Failure Rate (AFR) of 0.55%) � Incorporates industry-standard Self-Monitoring Analysis and Reporting Technology (S.M.A.R.T.) � 5-year warranty 3.5 Formatted capacities Standard OEM models are formatted to 512 bytes per block. The block size is selectable at format time and must be one of the supported sizes listed in the table below. Seagate designs specify capacity points at certain block sizes that Seagate guarantees current and future produ
ページ14に含まれる内容の要旨
10 Cheetah 15K.6 SAS Product Manual, Rev. B
ページ15に含まれる内容の要旨
4.0 Performance characteristics This section provides detailed information concerning performance-related characteristics and features of Cheetah 15K.6 drives. 4.1 Internal drive characteristics ST3450856SS ST3300656SS ST3146356SS ST3450056SS ST3300056SS ST3146756SS * Drive capacity 450 300 146 Gbytes (formatted, rounded off value) Read/write data heads 8 6 3 Tracks per inch 150,000 150,000 150,000 TPI Peak bits per inch 1,100 1,100 1,100 KBPI 2 Areal Density 165 165 165 Gbits/inch Internal d
ページ16に含まれる内容の要旨
4.2.2 Format command execution time (minutes) When changing sector sizes, the format times shown below may need to be increased by 30 minutes. ST3450856SS ST3300656SS ST3146356SS ST3450056SS ST3300056SS ST3146756SS 176 144 100 Maximum (with verify) 88 72 50 Maximum (without verify) Note. There is no significant difference in the format time between FDE and non-FDE models of the same capacity. Execution time measured from receipt of the last byte of the Command Descriptor Block (CDB) to the
ページ17に含まれる内容の要旨
If the drive receives a START STOP UNIT command with the START bit equal to 0 before receiving a NOTIFY (ENABLE SPINUP) primitive, the drive waits for a START STOP UNIT command with the START bit equal to 1. After receiving a START STOP UNIT command with the START bit equal to 1, the drive waits for a NOTIFY (ENABLE SPINUP) primitive. After receiving a NOTIFY (ENABLE SPINUP) primitive through either port, the drive becomes ready for normal operations within 20 seconds (excluding the error re
ページ18に含まれる内容の要旨
Note. The size of each segment is not reported by Mode Sense command page 08h, bytes 14 and 15. The value 0XFFFF is always reported regardless of the actual size of the segment. Sending a size specification using the Mode Select command (bytes 14 and 15) does not set up a new segment size. If the STRICT bit in Mode page 00h (byte 2, bit 1) is set to one, the drive responds as it does for any attempt to change an unchangeable parameter. 4.5.1 Caching write data Write caching is a write opera
ページ19に含まれる内容の要旨
5.0 Reliability specifications The following reliability specifications assume correct host and drive operational interface, including all inter- face timings, power supply voltages, environmental requirements and drive mounting constraints. 8 Seek error rate: Less than 10 errors in 10 seeks Read Error Rates 12 Recovered Data Less than 10 errors in 10 bits transferred (OEM default settings) 16 Unrecovered Data Less than 1 sector in 10 bits transferred 21 Miscorrected Data Less than 1 sector i
ページ20に含まれる内容の要旨
5.1.3 Seek errors A seek error is defined as a failure of the drive to position the heads to the addressed track. After detecting an initial seek error, the drive automatically performs an error recovery process. If the error recovery process fails, a seek positioning error (Error code = 15h or 02h) will be reported with a Hardware error (04h) in the Sense 8 Key. Recoverable seek errors are specified at Less than 10 errors in 10 seeks. Unrecoverable seek errors (Sense Key = 04h) are clas
