ページ1に含まれる内容の要旨
Hi-Speed USB Carrier
NI USB-9162
Hi-SPeed USB Carrier
NI USB-9162
USER GUIDE AND SPECIFICATIONS
NI USB-9229/9239
4-Channel, 24-Bit Analog Voltage Input Module
This user guide describes how to use the National Instruments
USB-9229/9239 and lists the device specifications. In this document,
the NI USB-9229 and NI USB-9239 are referred to inclusively as the
NI USB-9229/9239.
Introduction
The NI USB-9229/9239 provides a USB interface for four channels of
24-bit simultaneous analog input with inte
ページ2に含まれる内容の要旨
Dimensions Figure 2 shows the NI USB-9229/9239 device dimensions. Hi-Speed USB Carrier NI USB-9162 120.68 mm (4.751 in.) 118.26 mm (4.656 in.) 88.12 mm 25.34 mm (3.469 in.) (0.998 in.) Figure 2. NI USB-9229/9239 Device in Millimeters (Inches) Safety Guidelines Operate the NI USB-9229/9239 only as described in these operating instructions. Hot Surface This icon denotes that the component may be hot. Touching this component may result in bodily injury. Safety Guidelines for Hazardous Voltages
ページ3に含まれる内容の要旨
Caution Make sure that devices and circuits connected to the module are properly insulated from human contact. Caution When module terminals are hazardous voltage LIVE (>42.4V /60 VDC), you pk must ensure that devices and circuits connected to the module are properly insulated from human contact. You must use the NI 9971 connector backshell kit to ensure that the terminals are not accessible. Figure 3 shows the NI 9971 connector backshell. Figure 3. NI 9971 Connector Backshell Refer to the
ページ4に含まれる内容の要旨
The NI-DAQmx Help contains general information about measurement concepts, key NI-DAQmx concepts, and common applications that are applicable to all programming environments. Select Start»All Programs»National Instruments»NI-DAQ»NI-DAQmx Help. LabVIEW If you are a new user, use the Getting Started with LabVIEW manual to familiarize yourself with the LabVIEW graphical programming environment and the basic LabVIEW features you use to build data acquisition and instrument control applications.
ページ5に含まれる内容の要旨
Measurement Studio If you program your NI-DAQmx-supported device in Measurement Studio using Visual C++, Visual C#, or Visual Basic .NET, you can interactively create channels and tasks by launching the DAQ Assistant from MAX or from within Visual Studio .NET. You can generate the configuration code based on your task or channel in Measurement Studio. Refer to the DAQ Assistant Help for additional information about generating code. You also can create channels and tasks, and write your own
ページ6に含まれる内容の要旨
The installed documentation contains the NI-DAQmx API overview, measurement tasks and concepts, and function reference. This help is fully integrated into the Visual Studio .NET documentation. To view the NI-DAQmx .NET documentation, go to Start»Programs»National Instruments»NI-DAQ»NI-DAQmx .NET Reference Help. Expand NI Measurement Studio Help»NI Measurement Studio .NET Class Library»Reference to view the function reference. Expand NI Measurement Studio Help»NI Measurement Studio .NET Cl
ページ7に含まれる内容の要旨
Installing Other Software If you are using other software, refer to the installation instructions that accompany your software. Example Programs The NI-DAQmx CD contains example programs that you can use to get started programming with the NI USB-9229/9239. Refer to the NI-DAQmx for USB Devices Getting Started Guide that shipped with your device, and is also accessible from Start»All Programs»National Instruments» NI-DAQ, for more information. Installing the NI USB-9229/9239 Device Before in
ページ8に含まれる内容の要旨
5. Press firmly on the connector side of the NI 9229/9239 module until the latches lock the module into place, as shown in Figure 5. Figure 5. Locking Module into Place Mounting the NI USB-9229/9239 to a Panel Threaded inserts are located in the NI USB-9229/9239 for mounting it to a panel. Refer to Figure 6 for dimensions. 85.7 mm (3.37 in.) 72.2 mm (2.84 in.) Threaded Insert M3 x 0.5 8.5 mm (0.34 in.) Max Depth 76.1 mm (3.00 in.) Figure 6. Module Dimensions In Millimeters (Inches) Connect
ページ9に含まれる内容の要旨
LED Indicator The NI USB-9229/9239 device has a green LED next to the USB connector. The LED indicator indicates device status, as listed in Table 1. When the device is connected to a USB port, the LED blinks steadily to indicate that the device is initialized and is receiving power from the connection. If the LED is not blinking, it may mean that the device is not initialized or the computer is in standby mode. In order for the device to be recognized, the device must be connected to a co
ページ10に含まれる内容の要旨
source to the AI– terminal. Refer to Table 3 for the terminal assignments for each channel. Table 3. Terminal Assignments Module Channel Terminal Signal 0+ AI0+ 0 0– AI0– 0+ Ch 0 0- 1+ AI1+ 1+ 1 Ch 1 1– AI1– 1- 2+ AI2+ 2+ Ch 2 2- 2 2– AI2– 3+ Ch 3 3+ AI3+ 3- 3 3– AI3– Wiring for High-Vibration Applications If an application is subject to high vibration, National Instruments recommends that you either use ferrules to terminate wires to the detachable screw-terminal connector or use the NI 997
ページ11に含まれる内容の要旨
Connecting Signal Sources to the NI USB-9229/9239 You can connect ground-referenced or floating signal sources to the NI USB-9229/9239. If you make a ground-referenced connection between the signal source and the NI USB-9229/9239, make sure the voltage on the AI+ and AI– connections are in the channel-to-earth safety voltage range to ensure proper operation of the NI USB-9229/9239. Refer to the Specifications section for more information about operating voltages and overvoltage protection.
ページ12に含まれる内容の要旨
Each channel provides an independent signal path and ADC, enabling you to sample all four channels simultaneously. Refer to Figure 10 for an illustration of the circuitry for one channel. AI+ Overvoltage ADC Protection AI– Amplifier Prefilter NI USB-9229/9239 Figure 10. Input Circuitry for One Channel Understanding NI USB-9229/9239 Filtering The NI USB-9229/9239 uses a combination of analog and digital filtering to provide an accurate representation of in-band signals while rejecting out-
ページ13に含まれる内容の要旨
Passband The signals within the passband have frequency-dependent gain or attenuation. The small amount of variation in gain with respect to frequency is called the passband flatness. The digital filters of the NI USB-9229/9239 adjust the frequency range of the passband to match the data rate. Therefore, the amount of gain or attenuation at a given frequency depends on the data rate. Figure 11 shows typical passband flatness for the 50 kS/s data rate. 0.025 0.000 –0.025 –0.050 0 5 10 15
ページ14に含まれる内容の要旨
Specifications The following specifications are typical for the range 0 to 60 °C unless otherwise noted. All voltages are relative to the AI– signal on each channel unless otherwise noted. Input Characteristics Number of channels................................4 analog input channels ADC resolution.......................................24 bits Type of ADC ..........................................Delta-Sigma (with analog prefiltering) Sampling mode .......................................Simul
ページ15に含まれる内容の要旨
Accuracy, NI USB-9229 Percent of Percent of Reading Range* Error (Gain Error) (Offset Error) Calibrated max (–0 to 60 °C) ±0.13% ±0.05% Calibrated typ (25 °C, ±5 °C) ±0.03% ±0.008% Uncalibrated max (0 to 60 °C) ±1.2% ±0.55% Uncalibrated typ (25 °C, ±5 °C) ±0.3% ±0.11% * Range equals 62.64 V Accuracy, NI USB-9239 Percent of Percent of Reading Range* Error (Gain Error) (Offset Error) Calibrated max (0 to 60 °C) ±0.13% ±0.05% Calibrated typ (25 °C, ±5 °C) ±0.03% ±0.008% Uncalibrated max (0 to 60
ページ16に含まれる内容の要旨
1 NI USB-9229...................................0.045°/kHz + 360°· f /M in clk 1 NI USB-9239...................................0.075°/kHz + 360°· f /M in clk Phase nonlinearity (f = 50 kS/s).............0.11° max s Input delay NI USB-9229...................................38.4/f + 2.6 μs s NI USB-9239...................................38.4/f + 3 μs s Passband Frequency ........................................0.453 · f s Flatness (f = 50 kS/s)......................±100 mdB max s Stopband Freque
ページ17に含まれる内容の要旨
Physical Characteristics Screw-terminal wiring............................ 16 to 28 AWG copper conductor wire with 7 mm (0.28 in.) of insulation stripped from the end Torque for screw terminals .................... 0.22 to 0.25 N · m (1.95to 2.21 lb · in.) 2 2 Ferrules................................................... 0.25 mm to 0.5 mm Weight.................................................... 249 g (8.8 oz) Safety If you need to clean the module, wipe it with a dry towel. Safety Voltages Is
ページ18に含まれる内容の要旨
Note For UL and other safety certifications, refer to the product label or visit ni.com/ certification, search for the module number or product line, and click the appropriate link in the Certification column. Hazardous Locations The NI USB-9229/9239 is not certified for use in hazardous locations. Environmental The NI USB-9229/9239 devices are intended for indoor use only but may be used outdoors if installed in a suitable enclosure. Operating temperature (IEC 60068-2-1, IEC 60068-2-2) ......
ページ19に含まれる内容の要旨
CE Compliance This product meets the essential requirements of applicable European Directives, as amended for CE marking, as follows: � 2006/95/EC; Low-Voltage Directive (safety) � 2004/108/EEC; Electromagnetic Compatibility Directive (EMC) Note Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory compliance information. To obtain the DoC for this product, visit ni.com/ certification, search by model number or product line, and click the appropriate link
ページ20に含まれる内容の要旨
Where to Go for Support The National Instruments Web site is your complete resource for technical support. At ni.com/support you have access to everything from troubleshooting and application development self-help resources to email and phone assistance from NI Application Engineers. National Instruments corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas, 78759-3504. National Instruments also has offices located around the world to help address your support ne
