ページ1に含まれる内容の要旨
®
DataTraveler Locker+
®
This document is designed to help users with the DataTraveler Locker+ security application. For
additional support, please visit our on-line technical support site at www.kingston.com/support.
• The DataTraveler Locker+ is USB 2.0 High Speed compliant.
• It is comprised of a 100% Secure Partition backed by a Complex Password.
• For additional security, the DataTraveler Locker+ incorporates a Hardware Based Encryption.
®
Document No: 4808071
ページ2に含まれる内容の要旨
TABLE OF CONTENTS 1 Requirements........................................................................................................................ 3 1.1 System ........................................................................................................................... 3 1.2 Recommendations ......................................................................................................... 3 2 Getting Started (Windows)...............................
ページ3に含まれる内容の要旨
1 REQUIREMENTS 1.1 System Windows • Pentium III Processor • 16MB free disk space • USB 2.0 • Operating Systems ® o Windows 2000, SP4 ® o Windows XP (Home and Professional), SP1, SP2 and SP3 ® o Windows Vista, SP1 and SP2 ® o Windows 7 ● Two available drive letters between physical drives and network shares. Mac • 16MB free disk space • USB 2.0 • Operating Systems o Mac OS X 10.4.x - 10.6 1.2 Recommendations • Mac - Avoid the use of keyboard USB ports an
ページ4に含まれる内容の要旨
This area provides additional tips, warnings, notes, etc. where needed. Throughout 2 GETTING STARTED (WINDOWS) this document you may see the following symbols. 2.1 Initial Setup ® 1. Insert the DataTraveler directly into an available USB port of a computer operating a These symbols are an compatible Windows based system. A Found New Hardware message may appear indication that additional (Figure 1). information is available in this area. Figure 1: New Hard
ページ5に含まれる内容の要旨
4. Accept the License Agreement to continue. 5. Set a device password for data protection (Figure 3). This password will enable the drive The password must be a to be used as removable storage. It will also protect the data stored on the drive. minimum of 6 characters and must not exceed 16 6. Re-enter the password for confirmation. characters. It must also contain three of the following four characters: lower case letters, upper case letters, numeric charact
ページ6に含まれる内容の要旨
8. Enter your Contact Information into the corresponding field (Figure 4). Click Finish to continue. Figure 4: Contact Information 9. The Wizard will automatically format the drive. Never remove the DTLocker+ drive during the format process. Figure 5: DTLocker+ Format 10. A Format Complete window will display after the format is done (Figure 5). Click OK to complete the initial DTLocker+ s
ページ7に含まれる内容の要旨
3 USING DTLOCKER+ (WINDOWS) 3.1 Login to DTLocker+ 1. After the initial Setup is complete, you will automatically be logged into DTLocker+. Hereafter, you will login to DTLocker+ promptly after inserting the drive into the USB port. If you were not automatically logged in by the initial setup, enter your password to access the data stored on the DTLocker+ drive (Figure 6). Figure 6: DTLocker+ Logi
ページ8に含まれる内容の要旨
3.3 Exploring the DTLocker+ Features Additional features are available via the DTLocker+ icon located in the System Tray (Figure8). Windows 7 users may need to The options are as follows: click “Show hidden icons” arrow to display the ettings – Allows you to select the Language your DTLocker+ features will • DTLocker+ S DTLocker+ System Tray icon. display in. You can also change the Contact Information and the Password / Password Hint. • Browse DTLoc
ページ9に含まれる内容の要旨
• Format DTLocker+ – This option is used to format your DataTraveler Locker+ drive (Figure 9). All data in the read/ write partition will be lost! The DTLocker+ password is required in Windows XP/2000 (non admin users) and Windows 7 and Vista (all users) to format the drive. DTLocker+ includes a “lockdown” for enhanced security. This lockdown will lock the DTLocker+ whenever a maximum number of unsuccessful password attempts exceed a pre
ページ10に含まれる内容の要旨
3.4 Secure Storage In addition to the complex password, all of the data stored on the DTLocker+ is secured with a 256-bit AES Hardware Based Encryption. The DTLocker+ also includes a “lockdown” for enhanced security. This lockdown will permanently block the DTLocker+ whenever a maximum number of unsuccessful password attempts exceed a pre-configured value (the default value for the DTLocker+ is 10). In such an event, you will be forced to format DTLocker+ t
ページ11に含まれる内容の要旨
4 GETTING STARTED (MAC) 4.1 Initial Setup ® 1. Insert the DataTraveler Locker+ (DTLocker+) directly into an available USB port of a computer operating a compatible Mac OS X system. Double-click on the DTLplus icon which appears on the Desktop (Figure 11). Figure 11: DTLplus (Mac) Desktop Icon ® Document No: 4808071-001.A01
ページ12に含まれる内容の要旨
2. Select the Mac folder. Once the folder opens, double-click the DTLocker+ application icon to launch the DTLocker+ Setup Wizard (Figure 12). Figure 12: DTLocker+ (Mac) Folder 3. The DTLocker+ Setup Wizard will guide you through the initial setup. Select your language and click Next (Figure 13). Accept the license agreement to continue. Figure 13: DTVP (Mac) Setup Wizard ® Document No: 4808071-001.A01
ページ13に含まれる内容の要旨
4. Set a device password for data protection (Figure 14). This password will enable the drive to be used as removable storage. It will also protect the data stored on the drive. 5. Re-enter the password for confirmation. The password must be a minimum of 6 characters and must not exceed 16 characters. It must also contain three of the following four characters: lower case letters, upper case letters, numeric characters and/or special characters.
ページ14に含まれる内容の要旨
7. Enter your Contact Information into the corresponding fields (Figure 15). Click Next to continue. Figure 15: DTLocker+ (Mac) Contact Information 8. The Wizard will automatically format the drive. Never remove or attempt to access the DTLocker+ drive during the format process! Figure 16: DTLocker+ (Mac) Format Complete 9. A Format Complete window will di
ページ15に含まれる内容の要旨
5 USING DTLOCKER+ (MAC) 5.1 Login to DTLocker+ 1. After the initial Setup is complete, you will automatically be logged into DTLocker+. However, hereafter you will manually login to DTLocker+ after inserting the drive into the USB port. Locate and launch the DTLocker+ application via DTLplus>Mac. Enter your password to access the data stored on the DTLocker+ drive (Figure 17). Figure 17: DTLocker+ (Mac)
ページ16に含まれる内容の要旨
5.3 Exploring the DTLocker+ Features Additional features are available via the DTLocker+ icon located in the Mac Dock (Figure 19). Click and hold the DTLocker+ icon to view the features below. Mac OS X 10.6 users may need to press and hold the control key prior to selecting the DTLplus icon to display these features. Figure 19: DTLocker+ (Mac) Icon Features • DTLocker+ Settings – Allows you to
ページ17に含まれる内容の要旨
® • Format DTLocker+ – This option is used to Erase your DataTraveler Locker+ drive (Figure 20). All data in the read/write partition will be lost during format! DTLocker+ includes “lockdown” for enhanced security. This lockdown will lock the DTLocker+ whenever a maximum number of unsuccessful password attempts exceed a pre-configured value. Internet connection is required for the “Online Support” feature to work. Figure 20
ページ18に含まれる内容の要旨
• Hide/Show - Will minimize and/or maximize the active/visible DTLocker+ window. The “Quit” feature will • Quit - Will discontinue access to the data partition. remove the Kingston partition from the Desktop. However, to dismount the CD partition, you must drag the CD icon to the trash. 5.4 Safely Eject DTLocker+ 1. To safely eject the DTLocker+ drive, select “Shut down DTLocker+” from the Mac Dock icon (Figure 21). You can now safely eject the DTLocker+
ページ19に含まれる内容の要旨
Secure Storage In addition to the complex password, all of the data stored on the DTLocker+ is secured with a 256-bit AES Hardware Based Encryption. The DTLocker+ also includes a “lockdown” for enhanced security. This lockdown will permanently block the DTLocker+ whenever a maximum number of unsuccessful password attempts exceed a pre-configured value (the default value for the DTLocker+ is 10). In such an event, you will be forced to All data will be los
ページ20に含まれる内容の要旨
6 FAQS FAQs are used to bring you frequently asked questions, which may surface during the use of a product. Below we have posted the most common FAQs for quick viewing. For the latest technical documentation, please visit Kingston’s on-line technical support at www.kingston.com/support. Q1) I inserted the DTLocker+ and it does not show up in Computer (My Computer) or I receive a “DTLocker+ requires two free drive letters” error message. A1) This is a common Windows
