ページ1に含まれる内容の要旨
DVD-ROM DRIVE
INSTRUCTIONS
MC-D207U
For Customer Use:
Enter below the Model No. and Serial
No. which are located at the top of the
unit. Retain this information for future
reference.
Model No. MC-D207U
Serial No.
This instruction manual has been manufactured from 100% recycled paper.
LST0038-001B
FRANÇAIS DEUTSCH ENGLISH
ページ2に含まれる内容の要旨
Thank you for purchasing the JVC MC-D207U DVD-ROM DRIVE. Before you start operating this unit, please read the instructions carefully in order to obtain the best possible performance. 1. DANGER: Invisivle laser radiation will occur when the unit is open with a failed or defeated interlock. 2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to quali- fied service personnel. 2
ページ3に含まれる内容の要旨
● This unit is a DVD-ROM drive with a 7x speed capability. It especially designed for the JVC CD-ROM Library or CD/DVD Library. It is not compatible with the MC-7000 series “DVD-RAM Library”. ● The MC-D207U cannot be operated separately. ● A DVD videodisk playback is not possible with the MC-D207U. ROM Replacement When this drive is mounted in the MC-1200U/1600U or MC-2200U/2600U CD-ROM Library, certain serial numbers may require to replace the ROM. Read the section “ROM REPLACEMENT IN THE CD-R
ページ4に含まれる内容の要旨
INSTALLATION 2. How to Open the Drive Storage Cover Drive No.6 • Figure shows the MC-2200U Drive No.5 or MC-8200U Please also refer to the corresponding sections in the Drive No.4 Drive storage Library instructions. Drive No.3 section Drive No.2 1. Remove the screws from the drive section cover, Drive No.1 which is located at the rear of the Library. Drive storage cover 2. Remove the drive storage cover. Screws • Figure shows the MC-2100U Drive No.4 Drive storage or MC-8100U Drive No.3 secti
ページ5に含まれる内容の要旨
INSTALLATION 5. How To Connect Cables To The DVD-ROM Drive 1. Connect the power supply cable, control cable and SCSI cable to the connectors at the rear of the DVD-ROM Drive. Connect to the drive the power supply cable and control cable which extend from the side of the DVD-ROM drive installation slot. With the MC-2100U and the MC-8100U models be sure to connect a control cable with the same component No., as the drive bay No., otherwise proper operation may not be possible. Insert all co
ページ6に含まれる内容の要旨
INSTALLATION 2. ID2 - ID0 : This sets the SCSI ID No. on the drives. Switch SCSI ID Remarks No. ID2 ID1 ID0 0 OFF OFF OFF 1 OFF OFF ON Default factory setting 2 OFF ON OFF 3 OFF ON ON 4 ON OFF OFF 5 ON OFF ON 6 ON ON OFF 7 ON ON ON Set the SCSI ID No. between 0 - 7 using only an ID No. that is not being used by other SCSI devices. For the details on default factory settings, please refer to the section “SCSI ID No. SETTING” of the instructions for the JVC CD-ROM or CD/DVD Library. 3. Set t
ページ7に含まれる内容の要旨
ROM REPLACEMENT IN THE CD-ROM LIBRARY If the DVD-ROM drive is being mounted in a MC-2200U/2200PU/2600U/2600PU or MC-1200U/1600U CD-ROM Library and does not meet the following conditions, the ROM is required to be replaced in the Library. Please consult your dealer or nearest JVC-authorized service agent for ROM replacement. The library already has a MC-D207U mounted within the unit. The library already has a MC-D104U or a MC-R18U drive mounted within the unit. The library is a MC-2200U/220
ページ8に含まれる内容の要旨
MC-D207U DVD-ROM DRIVE VICTOR COMPANY OF JAPAN, LIMITED is a registered Trademark owned by VICTOR COMPANY OF JAPAN, LTD. is a registered Trademark in JAPAN, the U.S.A., the U.K. and many other countries. Printed in Japan © 2002 VICTOR COMPANY OF JAPAN, LIMITED LST0038-001B
