ページ1に含まれる内容の要旨
C156-E142-02EN
MCE3130AP, MCE3064AP,
MCF3064AP
OPTICAL DISK DRIVES
PRODUCT MANUAL
ページ2に含まれる内容の要旨
The contents of this manual is subject to change without prior notice. All Rights Reserved. Copyright ! 2001 FUJITSU LIMITED
ページ3に含まれる内容の要旨
REVISION RECORD Edition Date published Revised contents 01 February, 2000 02 March, 2001 Specification No.: C156-E142-**EN C156-E142-02EN i
ページ4に含まれる内容の要旨
PREFACE This manual describes the MCE3130AP, MCE3064AP and MCF3064AP 90mm(3.5-inch) optical disk drives. This manual explains the specifications of the above optical disk drive (ODD) and function of the ATAPI that interfaces to the user's system. The manual is intended for users who have a basic understanding of optical disk drives and their use in computer systems. See "Manual Organization" for details on the organization of manuals related to the optical disk drives and the scope of this manua
ページ5に含まれる内容の要旨
Conventions for Alert Messages This manual uses the following conventions to show the alert messages. An alert message consists of an alert signal and alert statements. The alert signal consists of an alert symbol and a signal word or just a signal word. The following are the alert signals and their meanings: This indicates a hazardous situation likely to result in serious personal injury if the user does not perform the procedure correctly. This indicates a hazardous situation could result in
ページ6に含まれる内容の要旨
DISCLAIMER Failure of the MCE3130AP, MCE3064AP and MCF3064AP optical disk drives are defined as a failure requiring adjustment, repair, or replacement. Fujitsu is not responsible for failure due to misuse, operation outside the specified environment conditions, power line trouble, controller problems, cable failure, or other failure not caused by the optical disk drive itself. C156-E142-02EN v
ページ7に含まれる内容の要旨
Important Alert Items Important Alert Messages The important alert messages in this manual are as follows: A hazardous situation could result in minor or moderate personal injury if the user does not perform the procedure correctly. This alert signal also indicates that damages to the product or other property, may occur if the user does not perform the procedure correctly. Task Alert message Page Operation 3-1 Low temperature burns The surface temperatures of some ICs on the printed circuit bo
ページ8に含まれる内容の要旨
Task Alert message Page Installation 3-18 Device Damage Be sure to turn on the power supply before inserting your cartridge for the first time. It releases the device from transport protection and enables you to insert the cartridge. The device may be damaged if you insert the cartridge without releasing the protection. From the next time, you don’t need to turn on the power supply beforehand. Before moving the drive, remove the optical disk cartridge. If the drive is moved with the optical di
ページ9に含まれる内容の要旨
MANUAL ORGANIZATION MCE3130AP, GENERAL DESCRIPTION MCE3064AP and MCF3064AP SPECIFICATIONS OPTICAL DISK DRIVE INSTALLATION REQUIREMENTS PRODUCT MANUAL HOST INTERFACE OPERATION AND CLEANING (C156-E142) DIAGNOSIS AND MAINTENANCE MCE3130AP, MAINTENANCE AND DIAGNOSIS MCE3064AP and MCF3064AP FAULT ANALYSIS OPTICAL DISK DRIVE REMOVAL AND REPLACEMENT PROCEDURES MAINTENANCE MANUAL PRINCIPLES OF OPERATION CLEANING viii C156-E142-02EN
ページ10に含まれる内容の要旨
REFERENCED STANDARDS Item Number Name Organization 1 X3T13/1321D AT Attachment with Packet Interface-5 American National Revision 2 (ATA/ATAPI-5) Standards Institute (ANSI) 2 SFF-8070I ATAPI Removable Rewritable Media Small Form Factor Revision 1.2 Committee (SFF) 3 ISO/IEC 10090 90 mm optical disk cartridges, rewritable ISO/IEC and read only, for data interchange 4 ISO/IEC 13963 Data interchange on 90 mm optical disk ISO/IEC cartridges, – Capacity: 230 megabytes per cartridge 5 ISO/IEC 15041
ページ11に含まれる内容の要旨
CONTENTS page CHAPTER 1 GENERAL DESCRIPTION ................................................................................1 - 1 1.1 Features.................................................................................................................................1 - 1 1.1.1 Performance ..........................................................................................................................1 - 2 1.1.2 Reliability............................................................
ページ12に含まれる内容の要旨
3.1.3 Air flow.................................................................................................................................3 - 3 3.1.4 Temperature rise under several conditions............................................................................3 - 4 3.1.5 Air purity...............................................................................................................................3 - 4 3.2 Mounting Requirements................................................
ページ13に含まれる内容の要旨
4.3.1.6 ATAPI Byte Count register...................................................................................................4 - 7 4.3.1.7 ATAPI Block Device Select register ....................................................................................4 - 8 4.3.1.8 Error register .........................................................................................................................4 - 8 4.3.1.9 ATA Features register..................................................
ページ14に含まれる内容の要旨
4.5.7 IDLE IMMEDIATE (X'95'/X'E1') ........................................................................................4 - 31 4.5.8 NOP (X'00')...........................................................................................................................4 - 32 4.5.9 SERVICE (X'A2') (Not supported).......................................................................................4 - 32 4.5.10 SET FEATURES (X'EF').................................................................
ページ15に含まれる内容の要旨
4.6.24 WRITE AND VERIFY command ........................................................................................4 - 71 4.6.25 WRITE BUFFER command .................................................................................................4 - 72 4.6.26 WRITE LONG command .....................................................................................................4 - 74 4.7 Timing.................................................................................................
ページ16に含まれる内容の要旨
FIGURES page 1.1 Outer view (with panel).........................................................................................................1 - 6 1.2 Outer view (without panel)....................................................................................................1 - 6 1.3 Optical disk drive configuration............................................................................................1 - 7 1.4 Control circuit section block diagram .....................................
ページ17に含まれる内容の要旨
5.3 Removing cartridge...............................................................................................................5 - 5 5.4 Optial disk cartridge..............................................................................................................5 - 7 5.5 Write protect tab ...................................................................................................................5 - 8 5.6 Cleaning procedure (1)...................................................
ページ18に含まれる内容の要旨
TABLES page 2.1 Model and order number.......................................................................................................2 - 1 2.2 Specifications........................................................................................................................2 - 3 2.3 Environmental and power requirements................................................................................2 - 7 2.4 Recommended optical disk cartridge specifications..............................
ページ19に含まれる内容の要旨
4.25 EXECUTE DEVICE DIAGNOSTIC command ...................................................................4 - 29 4.26 Self-diagnosis detailed code..................................................................................................4 - 30 4.27 GET MEDIA STATUS command ........................................................................................4 - 30 4.28 Error register ........................................................................................................
ページ20に含まれる内容の要旨
4.61 Changeable values in the caching page .................................................................................4 - 49 4.62 Default values for the cashing page.......................................................................................4 - 49 4.63 Removable block access capabilities page............................................................................4 - 50 4.64 Changeable values in the removable block access capabilities page.....................................
