ページ1に含まれる内容の要旨
C141-E192-01EN
MHT2080AT, MHT2060AT, MHT2040AT
MHT2030AT, MHT2020AT
DISK DRIVES
PRODUCT MANUAL
ページ2に含まれる内容の要旨
FOR SAFE OPERATION Handling of This Manual This manual contains important information for using this product. Read thoroughly before using the product. Use this product only after thoroughly reading and understanding especially the section “Important Alert Items” in this manual. Keep this manual handy, and keep it carefully. FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering damage to their property. Use the product according to this manual. IMPOR
ページ3に含まれる内容の要旨
Revision History (1/1) Revised section (*1) Edition Date Details (Added/Deleted/Altered) 01 2003-01-20 *1 Section(s) with asterisk (*) refer to the previous edition when those were deleted. C141-E192-01EN
ページ4に含まれる内容の要旨
This page is intentionally left blank.
ページ5に含まれる内容の要旨
Preface This manual describes the MHT Series, 2.5-inch hard disk drives. These drives have a built-in controller that is compatible with the ATA interface. This manual describes the specifications and functions of the drives and explains in detail how to incorporate the drives into user systems. This manual assumes that the reader has a basic knowledge of hard disk drives and their implementations in computer systems. This manual consists of seven chapters and sections explaining the special t
ページ6に含まれる内容の要旨
Preface Conventions for Alert Messages This manual uses the following conventions to show the alert messages. An alert message consists of an alert signal and alert statements. The alert signal consists of an alert symbol and a signal word or just a signal word. The following are the alert signals and their meanings: This indicates a hazardous situation could result in minor or moderate personal injury if the user does not perform the procedure correctly. This alert signal also indicates that
ページ7に含まれる内容の要旨
Preface Attention Please forward any comments you may have regarding this manual. To make this manual easier for users to understand, opinions from readers are needed. Please write your opinions or requests on the Comment at the back of this manual and forward it to the address described in the sheet. Liability Exception “Disk drive defects” refers to defects that involve adjustment, repair, or replacement. Fujitsu is not liable for any other disk drive defects, such as those caused by user mis
ページ8に含まれる内容の要旨
This page is intentionally left blank.
ページ9に含まれる内容の要旨
Important Alert Items Important Alert Messages The important alert messages in this manual are as follows: A hazardous situation could result in minor or moderate personal injury if the user does not perform the procedure correctly. Also, damage to the product or other property, may occur if the user does not perform the procedure correctly. Task Alert message Page Normal Operation 3-7 Data corruption: Avoid mounting the disk near strong magnetic sources such as loud speakers. Ensure that the
ページ10に含まれる内容の要旨
This page is intentionally left blank.
ページ11に含まれる内容の要旨
Manual Organization MHT2080AT, MHT2060AT, • Device Overview MHT2040AT Device Configuration MHT2030AT, MHT2020AT Installation Conditions Theory of Device Operation DISK DRIVES Interface PRODUCT MANUAL Operations (C141-E192) MHT2080AT, MHT2060AT, Maintenance and Diagnosis MHT2040AT Removal and Replacement Procedure MHT2030AT, MHT2020AT DISK DRIVES MAINTENANCE MANUAL (C141-F063) C141-E192-01EN vii
ページ12に含まれる内容の要旨
This page is intentionally left blank.
ページ13に含まれる内容の要旨
Contents Device Overview ................................................................................................ 1-1 1.1 Features................................................................................................... 1-2 1.1.1 Functions and performance................................................................... 1-2 1.1.2 Adaptability .......................................................................................... 1-2 1.1.3 Interface .........................
ページ14に含まれる内容の要旨
Contents CHAPTER 3 Installation Conditions..............................................................3-1 3.1 Dimensions..............................................................................................3-2 3.2 Mounting.................................................................................................3-3 3.3 Cable Connections ..................................................................................3-9 3.3.1 Device connector.....................................
ページ15に含まれる内容の要旨
Contents 4.6.2 Write circuit.......................................................................................... 4-9 4.6.3 Read circuit......................................................................................... 4-11 4.6.4 Digital PLL circuit.............................................................................. 4-12 4.7 Servo Control........................................................................................ 4-13 4.7.1 Servo control circuit ................
ページ16に含まれる内容の要旨
Contents 5.5.3.1 Initiating an Ultra DMA data in burst.............................................5-119 5.5.3.2 The data in transfer .........................................................................5-120 5.5.3.3 Pausing an Ultra DMA data in burst...............................................5-120 5.5.3.4 Terminating an Ultra DMA data in burst........................................5-121 5.5.4 Ultra DMA data out commands ........................................................5-124 5.5.
ページ17に含まれる内容の要旨
Contents 6.2 Power Save.............................................................................................. 6-7 6.2.1 Power save mode .................................................................................. 6-7 6.2.2 Power commands.................................................................................. 6-9 6.3 Defect Processing ................................................................................... 6-9 6.3.1 Spare area....................................
ページ18に含まれる内容の要旨
Contents Illustrations Figures Figure 1.1 Negative voltage at +5 V when power is turned off ..........................1-6 Figure 1.2 Current fluctuation (Typ.) at +5 V when power is turned on ............1-8 Figure 2.1 Disk drive outerview..........................................................................2-2 Figure 2.2 1 drive system configuration..............................................................2-3 Figure 2.3 2 drives configuration ............................................
ページ19に含まれる内容の要旨
Contents Figure 5.3 Read Sector(s) command protocol.................................................5-110 Figure 5.4 Protocol for command abort ..........................................................5-111 Figure 5.5 WRITE SECTOR(S) command protocol.......................................5-113 Figure 5.6 Protocol for the command execution without data transfer...........5-114 Figure 5.7 Normal DMA data transfer ............................................................5-117 Figure 5.8 Ultra D
ページ20に含まれる内容の要旨
Contents Tables Table 1.1 Specifications.....................................................................................1-4 Table 1.2 Model names and product numbers ...................................................1-5 Table 1.3 Current and power dissipation ...........................................................1-7 Table 1.4 Environmental specifications.............................................................1-8 Table 1.5 Acoustic noise specification .............................
