ページ1に含まれる内容の要旨
C156-E205-01EN
MCJ3230AP
OPTICAL DISK DRIVE
PRODUCT MANUAL
ページ2に含まれる内容の要旨
FOR SAFE OPERATION Handling of This Manual This manual contains important information for using this product. Read thoroughly before using the product. Use this product only after thoroughly reading and understanding especially the section "Important Alert Items" in this manual. Keep this manual handy, and keep it carefully. FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering damage to their property. Use the product according to this manual. This
ページ3に含まれる内容の要旨
Revision History (1/1) Revised section (*1) Edition Date Details (Added/Deleted/Altered) 01 2001.07.24 — — *1 Section(s) with asterisk (*) refer to the previous edition when those were deleted. C156-E205-01EN
ページ4に含まれる内容の要旨
This page is intentionally left blank.
ページ5に含まれる内容の要旨
ページ6に含まれる内容の要旨
Preface This manual describes the MCJ3230AP 90 mm (3.5-inch) optical disk drive. This manual provides an overview of the above optical disk drives, and explains their specifications, the requirements and procedures for installing them in a system, and how to clean them. The manual is intended for users who have a basic understanding of optical disk drives and their use in computer systems. See "Manual Organization" for details of the organization of manuals related to optical disk drives and the
ページ7に含まれる内容の要旨
Preface Glossary The glossary describes the technical terms that need to be understood to read this manual. Acronyms and Abbreviations This manual contains a list of the abbreviations used in this manual and their meanings. CONVENTIONS USED IN THIS MANUAL Throughout this manual, the MCJ3230AP optical disk drive are described as an "ODD," "drive," "unit," "target (TARG)," or "device." Decimal values are indicated without any modifiers added. Hexadecimal values are indicated as X'17B9', 17B9h, 17B
ページ8に含まれる内容の要旨
Preface (Example) Low temperature burns: The surface temperatures of some ICs on the printed circuit board unit in the optical disk drive exceed 55°C while operating. Be careful of low tenperature burns. The main alert messages in the text are also listed in the “Important Alert Items.” Attention Please forward any comments you may have regarding this manual. To make this manual easier for users to understand, opinions from readers are needed. Please write your opinions or requests on the Comm
ページ9に含まれる内容の要旨
DISCLAIMER Failure of the MCJ3230AP optical disk drive is defined as a failure requiring adjustment, repair, or replacement. Fujitsu is not responsible for failure due to misuse, operation outside the specified environment conditions, power line trouble, controller problems, cable failure, or other failure not caused by the optical disk drive itself. iv C156-E205-01EN
ページ10に含まれる内容の要旨
Important Alert Items Important Alert Messages The important alert messages in this manual are as follows: A hazardous situation could result in minor or moderate personal injury if the user does not perform the procedure correctly. Also, damage to the product or other property, may occur if the user does not perform the procedure correctly. Task Alert message Page Operation 3-1 Low temperature burns: The surface temperatures of some ICs on the printed circuit board unit in the optical disk dri
ページ11に含まれる内容の要旨
Important Alert Items Task Alert message Page Installation 3-19 Device Damage: Be sure to turn on the power supply before inserting your cartridge for the first time. It releases the device from transport protection and enables you to insert the cartridge. The device may be damaged if you insert the cartridge without releasing the protection. From the next time, you don't need to turn on the power supply beforehand. Before moving the drive, remove the optical disk cartridge. If the drive is m
ページ12に含まれる内容の要旨
MANUAL ORGANIZATION OPTICAL DISK DRIVES 1. GENERAL DESCRIPTION PRODUCT MANUAL 2. SPECIFICATIONS (C156-E205) 3. INSTALLATION REQUIREMENTS 4. HOST INTERFACE 5. OPERATION AND CLEANING 6. DIAGNOSTICS AND MAINTENANCE OPTICAL DISK DRIVES 1. MAINTENANCE AND DIAGNOSIS MAINTENANCE MANUAL 2. FAULT ANALYSIS (C156-F043) 3. REMOVAL AND REPLACEMENT PROCEDURES 4. PRINCIPLES OF OPERATION 5. CLEANING C156-E205-01EN vii
ページ13に含まれる内容の要旨
REFERENCED STANDARDS The product specifications and functions described in this manual conform to the following standards: Specification Name Concerned organization (document) number X3T13/1321D AT Attachment with Packet Interface-5 American National Revision 2 (ATA/ATAPI-5) Standards Institute (ANSI) SFF-8070I ATAPI Rmovavle Rewritable Media Small From Factor Revision 1.2 Committee (SFF) ISO/IEC 10090 90mm Optical Disk Cartridges, rewritable and ISO/IEC (*1) read only, for data interchange. ISO
ページ14に含まれる内容の要旨
Contents CHAPTER 1 General Description.................................................................. 1-1 1.1 Features 1-1 1.1.1 Performance 1-2 1.1.2 Reliability 1-3 1.1.3 Maintainability/operability 1-3 1.1.4 Adaptability 1-4 1.1.5 Interface 1-4 1.2 Drive Configuration 1-6 1.2.1 Drive model 1-6 1.2.2 Configuration 1-7 1.2.3 Mechanical sections 1-7 1.2.4 Control circuit section 1-8 1.3 System Configuration 1-10 CHAPTER 2 Specifications.........
ページ15に含まれる内容の要旨
Contents 3.1.1 Temperature measurement point 3-1 3.1.2 Temperature requirements and measuring method 3-3 3.1.3 Air flow 3-3 3.1.4 Temperature rise under several conditions 3-4 3.1.5 Air purity 3-4 3.2 Mounting Requirements 3-5 3.2.1 External dimensions 3-5 3.2.2 Installation direction 3-8 3.2.3 Centers of gravity 3-9 3.2.4 Notes on mounting 3-10 3.3 Power Supply Requirements 3-12 3.4 Cable Connections 3-13 3.4.1 Drive connectors 3-13 3.4.2 Cabl
ページ16に含まれる内容の要旨
Contents 4.3 Interface Registers 4-6 4.3.1 I/O registers 4-6 4.3.1.1 Alternate Status register 4-7 4.3.1.2 ATA Command register 4-7 4.3.1.3 Data register 4-7 4.3.1.4 Device Control register 4-7 4.3.1.5 Drive Address register 4-8 4.3.1.6 ATAPI Byte Count register 4-8 4.3.1.7 ATAPI Block Device Select register 4-9 4.3.1.8 Error register 4-9 4.3.1.9 ATA Features register 4-10 4.3.1.10 ATAPI Features register 4-10 4.3.1.11 ATA Sector Count register
ページ17に含まれる内容の要旨
Contents 4.5.4 FLUSH CACHE (E7h) 4-25 4.5.5 GET MEDIA STATUS (DAh) 4-25 4.5.6 IDENTIFY PACKET DEVICE (A1h) 4-26 4.5.7 IDLE IMMEDIATE (E1h) 4-33 4.5.8 NOP (00h) 4-33 4.5.9 PACKET (A0h) 4-34 4.5.10 SET FEATURES (Efh) 4-35 4.5.11 SLEEP (E6h) 4-37 4.5.12 STANDBY IMMEDIATE (E0h) 4-38 4.6 Packet Commands 4-39 4.6.1 ERASE command 4-40 4.6.2 FORMAT UNIT command 4-41 4.6.3 INQUIRY command 4-42 4.6.4 MODE SELECT (6) command 4-44 4.6.4.1 Read-Write er
ページ18に含まれる内容の要旨
Contents 4.7.1 Register/PIO data transfer timing 4-78 4.7.2 Multiword DMA data transfer timing 4-80 4.7.3 Ultra DMA data in transfer (initialization timing) 4-82 4.7.4 Ultra DMA data in transfer (continuous transfer timing) 4-82 4.7.5 Ultra DMA data in transfer (host stop timing) 4-83 4.7.6 Ultra DMA data in transfer (device end timing) 4-83 4.7.7 Ultra DMA data in transfer (host end timing) 4-84 4.7.8 Ultra DMA data out transfer (initialization timing) 4-85 4.7.9
ページ19に含まれる内容の要旨
Contents 6.2.1 Maintenance requirements 6-3 6.2.2 Revision number 6-4 Glossary .................................................................................................GL-1 Abbreviations .................................................................................................AB-1 Index .................................................................................................. IN-1 xiv C156-E205-01EN
ページ20に含まれる内容の要旨
Contents Illustrations Figures Figure 1.1 Outer view (with panel) 1-6 Figure 1.2 Outer view (without panel) 1-6 Figure 1.3 Optical disk drive configuration 1-7 Figure 1.4 Control circuit section block diagram 1-8 Figure 1.5 System configuration with one optical disk drive 1-10 Figure 1.6 System configuration with two optical disk drives 1–10 Figure 2.1 Optical disk cartridge 2-8 Figure 2.2 Algorithms for alternate processing 2-11 Figure 2.3 Example of alternate pr
