ページ1に含まれる内容の要旨
Owner’s Manual
DVD-RAM drive unit with built-in HDD
Model EX12
Introduction
Thank you very much for purchasing the Fostex Model EX12.
The EX12 is a DVD-RAM drive unit dedicated to the PD-6. It in-
corporates a 12-cm DVD-RAM drive with a 2.5-inch HDD.
By connecting the EX12 to your PD-6, you can use two more drives
dedicated to the PD-6, in addition to the PD-6 internal DVD-RAM
drive.
Befo
ページ2に含まれる内容の要旨
CAUTION: CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE RISK OF ELECTRIC SHOCK OF PLUG TO WIDE SLOT, FULLY INSERT. DO NOT OPEN ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE DO NOT REMOVE COVER (OR BACK). ET POUSSER JUSQU' AU FOND. NO USER - SERVICEABLE PARTS INSIDE. The lightning flash with arrowhead symbol, within an REFER SERVICING TO QUA
ページ3に含まれる内容の要旨
Precautions • Make sure that the voltage of your AC power outlet matches the voltage requirements printed on the unit. • When disconnecting the AC cable, make sure that the unit [POWER] switch is set to "OFF". Disconnecting the AC cable while the power is "ON" may damage data because the unit always transfers data between the current card and memory. • While the unit is accessing the DVD-RAM disk or internal HDD (for example, during recording), never turn off the power. Make sure th
ページ4に含まれる内容の要旨
Names and functions 1 2 OPEN/CLOSE POWER ON PD-6 HD EX12 EXTERNAL DRIVE UNIT OFF IEEE1394/USB 7 6 5 4 3 8 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE DE CHOC ELECTRIQUE AVIS: NE PAS OUVRIR WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. 13 12 11 10 9 1) Fastenings : While the EX12 is in operation (i.e. during The left and right fastenings are used to fasten the recording or playback using the EX1
ページ5に含まれる内容の要旨
4) Fix the supplied cushion using the fixing screws How to stack the PD-6 and EX12 together which are removed in the previous step. 1) Remove the blank panel at the bottom of the PD-6. Cushion 5) Pull out the connection cable from inside the 2) Replace the two screws for fixing the rubber EX12. feet at the bottom of the PD-6 with the screws supplied with the EX12. : Never forget to replace the screws for fixing the rubber feet. Otherwise, the PD- 6 may
ページ6に含まれる内容の要旨
After hanging the projection on the PD-6, lift 7) After connecting the cable, stack the PD-6 on up the fixing angle until it is locked. the EX12. 1 2 OPEN/CLOSE POWER ON PD-6 HD EX12 EXTERNAL DRIVE UNIT OFF IEEE1394/USB 6 7 5 4 3 : When stacking the PD-6 on the EX12, 9) Fasten the fixing screw of each fastening. 8 make sure to perfectly fit the dent of PD-6 Fasten the fixing screw of each fastening so that rubber feet to the metallic projections of each the fastening may not be off. Be
ページ7に含まれる内容の要旨
Connecting the power cords To supply power to the PD-6 and EX12, connect the AC and DC cords supplied with the EX12, as shown below. Make connection using the supplied DC cord. This connector is used when using the external DC power supply. Connect to the AC outlet using the supplied AC cord. • When the EX12 is connected to the PD-6, turn on the EX12 first, followed by the PD-6. • When the EX12 is connected to the PD-6, make sure that both the PD-6 and EX12 are turned off before you swit
ページ8に含まれる内容の要旨
Connecting the EX12 alone to your PC By connecting the EX12 to your PC, you can export an audio file on a DVD-RAM disk set to the EX12. Note that you cannot export an audio file on the EX12 internal HDD. To the IEEE1394 or USB port on your PC • Set the selector on the EX12 front panel to "IEEE1394/USB". • Connect the EX12 to your PC via the IEEE1394 or USB port. Never use both ports together. Daisy-chaining the PD-6, EX12 and PC By making "daisy chain" of the PD-6, EX12 and P
ページ9に含まれる内容の要旨
Main specifications Internal drives: USB port (for PC connection) 12-cm DVD-RAM drive and 2.5-inch HDD (40 GB) Connector: USB Series "B" receptacle Pin assignment: Inputs/Outputs: 1: VBUS, 2: D- (DATA), 3: D+ (DATA), 4: GND DC12V IN Connector: XLR-4-32 type (male) External dimensions: Pin assignment: 386 (W) x 94 (H) x 231 (D) mm 1: GND, 2: NC, 3: NC, 4: +12~18 V Power requirement/power consumption: DC12V OUT (PD-6 ONLY) 100~240 VAC, 38W Connector: XLR-4-31 type (female) 12VDC 3A Pin assignment:
ページ10に含まれる内容の要旨
Declaration of EC Directive This equipment is compatible with the EMC Directive (89/336/EEC) - Directive on approximation of member nation's ordinance concerning the electromagnetic compatibility and with the Low Voltage Directive (73/23/EEC) - Directive on approximation of member nation's ordinance concerning electric equipment designed to be used within the specified voltage range. The Affect of Immunity on This Equipment The affect of the European Specification EN61000-6-1 (coexistence of ele
