ページ1に含まれる内容の要旨
APCC.book Page 1 Tuesday, March 9, 2010 4:25 PM
Dell™ PowerVault™ ML6000
Getting Started Guide (English)
Panduan Pengaktifan (Bahasa Indonesia)
スタートガイド (Japanese)
시작하기 설명서 (Korean)
入门指南 (Simplified Chinese)
*MK444 A03*
MK444 A03
www.dell.com | support.dell.com
ページ2に含まれる内容の要旨
APCC.book Page 2 Tuesday, March 9, 2010 4:25 PM Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Catatan, Perhatian, dan Peringatan CATATAN: CATATAN menunjukkan informasi penting yang dapat membantu Anda menggunakan k
ページ3に含まれる内容の要旨
APCC.book Page 3 Tuesday, March 9, 2010 4:25 PM 注、注意和警告 注：“注 ”表示可以帮助您更好地使用计算机的重要信息。 注意：“注意 ”表示如果不遵循说明，就有可能损坏硬件或导致数据丢失。 警告：“警告 ”表示可能会造成财产损失、人身伤害甚至死亡。 ____________________ Information in this document is subject to change without notice. © 2010 Dell Inc. All rights reserved. Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: Dell, the DELL logo, and PowerVault are trademarks of Dell Inc.
ページ4に含まれる内容の要旨
APCC.book Page 4 Tuesday, March 9, 2010 4:25 PM 이 문서의 정보는 공지없이 변경될 수 있습니다 . © 2010 Dell Inc. All rights reserved. Dell Inc.의 서면 동의 없이는 이러한 자료에 대한 일체의 모든 재생산은 엄격하게 금지됩니다 . 본 설명서에 사용된 상표인 Dell, DELL 로고 및 PowerVault는 Dell Inc.의 상표입니다 . LTO는 미국 및 다른 국가에서 IBM의 상표입니다 . 특정 회사의 표시나 회사명 또는 제품을 지칭하기 위해 다른 상표나 상표명을 본 설명서에서 사용할 수도 있습니다 . Dell Inc.은 자사가 소유한 상표 및 상표명 이외의 어떠한 소유권도 주 장하지 않습니다 . 本说明文件中的信息如有更改，恕不另行通知。 © 2010 Dell Inc. 版权所有，翻印必究。 未经 Dell Inc. 书面许可，严禁以任何形式复制这些材料。 本文中使用的商标：Dell、DELL 徽标和 PowerVa
ページ5に含まれる内容の要旨
APCC.book Page 5 Tuesday, March 9, 2010 4:25 PM Contents 1 Dell PowerVault ML6000 Getting Started Guide (English) . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Installing Your Library in a Rack . . . . . . . . . . . . 10 Special Instructions for LTO-5 Tape Drives . . . . . . . 10 Connecting Parallel SCSI Cables . . . . . . . . . . . . 12 Connecting Fibre Channel Cables to a Host or Switch . . 14 Connecting Fibre Channel Cables Through a Fibre Channel I/O Blade . . . . . . . . .
ページ6に含まれる内容の要旨
APCC.book Page 6 Tuesday, March 9, 2010 4:25 PM Menyambungkan Kabel Kanal Serat Melalui Blade I/O Kanal Serat . . . . . . . . . . . . . . . . . . . . . . 27 Menyambungkan Kabel Serial Attached SCSI (SAS) . . 29 Menyelesaikan Penyambungan Perpustakaan . . . . . 30 Menghidupkan Perpustakaan . . . . . . . . . . . . . . 31 Memulai pengaktifkan. . . . . . . . . . . . . . . . . . 32 3 Dell PowerVault ML6000 スタートガイド (Japanese) . . . . . . . . . . . . . . . . . . . . . . . . 33 ライブラリのラックへの取り付け
ページ7に含まれる内容の要旨
APCC.book Page 7 Tuesday, March 9, 2010 4:25 PM 병렬 SCSI 케이블 연결 . . . . . . . . . . . . . . . . . . . 48 호스트 또는 스위치에 Fibre Channel 케이블 연결. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Fibre Channel I/O 블레이드를 통해 Fibre Channel 케이블 연결. . . . . . . . . . . . . . . . . . . . . . . . . . 51 직렬 연결 SCSI(SAS) 케이블 연결 . . . . . . . . . . . . 53 라이브러리 배선 완료 . . . . . . . . . . . . . . . . . . . 54 라이브러리 전원 공급 . . . . . . . . . . . . . . . . . . . 55 시작하기. . . . . . . . . . . . .
ページ8に含まれる内容の要旨
APCC.book Page 8 Tuesday, March 9, 2010 4:25 PM 8 Contents
ページ9に含まれる内容の要旨
APCC.book Page 9 Tuesday, March 9, 2010 4:25 PM Dell PowerVault ML6000 Getting Started Guide (English) WARNING: Before cabling your library, read the Dell™ PowerVault™ Systems Product Information Guide. WARNING: All libraries must be installed in a rack having a main protective earthing (grounding) terminal. For detailed installation information, see the Dell™ PowerVault™ ML6000 Tape Library User’s Guide. WARNING: The socket outlet shall be installed near the equipment and shall be ea
ページ10に含まれる内容の要旨
APCC.book Page 10 Tuesday, March 9, 2010 4:25 PM Installing Your Library in a Rack All Dell™ PowerVault™ ML6000 libraries must be installed in a rack. For instructions, see the Dell™ PowerVault™ ML6000 Tape Library User’s Guide. � ML6010 CM is a single 5U Library Control Module. � ML6020 CM consists of one (1) ML6010 CM 5U Library Control Module and one (1) ML6000 EM 9U Library Expansion Module (14U total). � ML6030 CM consists of one (1) ML6010 CM 5U Library Control Module and two (2) M
ページ11に含まれる内容の要旨
APCC.book Page 11 Tuesday, March 9, 2010 4:25 PM � Port 2 on dual-port tape drives See the following two figures for details. LTO-5 Fibre Channel Tape Drive 1 Ethernet port - do not use 2 Fibre Channel port - use this port LTO-5 SAS Tape Drive 1 SAS port 1 - use this port 2 SAS port 2 - do not use 3 Ethernet port - do not use Dell PowerVault ML6000 Getting Started Guide 11
ページ12に含まれる内容の要旨
APCC.book Page 12 Tuesday, March 9, 2010 4:25 PM Connecting Parallel SCSI Cables Perform this step if your library contains parallel SCSI tape drives. There are two recommended ways to cable SCSI tape drives: one tape drive per SCSI bus or two tape drives per SCSI bus. NOTE: To avoid possible performance issues, do not connect more than two tape drives per SCSI bus. To connect one tape drive per SCSI bus: 1 Use a SCSI cable to connect the bottom port of the tape drive to your host system
ページ13に含まれる内容の要旨
APCC.book Page 13 Tuesday, March 9, 2010 4:25 PM 1 Connecting one tape drive per SCSI 2 Connecting two tape drives per SCSI bus bus 3 SCSI cable to host 4 SCSI terminator Dell PowerVault ML6000 Getting Started Guide 13
ページ14に含まれる内容の要旨
APCC.book Page 14 Tuesday, March 9, 2010 4:25 PM Connecting Fibre Channel Cables to a Host or Switch Perform this step if your library contains Fibre Channel tape drives that you will be connecting directly to a host or switch. Use Fibre Channel cables to connect your host (or switch) to the library. For each tape drive: 1 Connect one end of the Fibre Channel cable to the Fibre Channel port on the tape drive. 2 Connect the other end of the Fibre Channel cable to your host or switch. 1
ページ15に含まれる内容の要旨
APCC.book Page 15 Tuesday, March 9, 2010 4:25 PM Connecting Fibre Channel Cables Through a Fibre Channel I/O Blade Perform this step if your library contains Fibre Channel tape drives that you will be connecting to your host or switch through a Fibre Channel I/O blade. 1 For each tape drive: Connect one end of a Fibre Channel cable to the Fibre Channel port on the tape drive. Connect the other end of the Fibre Channel cable to an initiator port (lower ports 3 – 6) on the nearest Fibre C
ページ16に含まれる内容の要旨
APCC.book Page 16 Tuesday, March 9, 2010 4:25 PM 1 LCB middle Ethernet ports 2 Fibre Channel I/O blade 3 Target ports 4 Initiator ports 5 Fibre Channel port 6 Ethernet cables 7 "UPPER" and "LOWER" ports Connecting Serial Attached SCSI (SAS) Cables Perform this step if your library contains serial attached SCSI (SAS) tape drives. Use SAS cables to connect the SAS tape drives directly to the host. For each tape drive: 1 Connect one end of the SAS cable to the SAS port on the tape drive. 2
ページ17に含まれる内容の要旨
APCC.book Page 17 Tuesday, March 9, 2010 4:25 PM 1 SAS port 2 SAS cable Dell PowerVault ML6000 Getting Started Guide 17
ページ18に含まれる内容の要旨
APCC.book Page 18 Tuesday, March 9, 2010 4:25 PM Finishing Cabling the Library All libraries must use module terminators. Libraries that consist of multiple modules must use module-to-module cables. CAUTION: The module terminator is not the same as a SCSI terminator. Using a SCSI terminator instead of a module terminator can damage the library. The module terminators are located in a plastic package tied to the back of the 5U Library Control Module. 1 Remove the protective plastic caps c
ページ19に含まれる内容の要旨
APCC.book Page 19 Tuesday, March 9, 2010 4:25 PM 1 Module terminator 2 Ethernet cable connected to Gigabit Ethernet port 3 Module-to-module cable 4 Power cords Powering On the Library 1 Turn on each power supply’s power switch. 2 Turn on the library’s main power using the power button located on the front of the 5U Library Control Module. The Setup Wizard screen appears on the operator panel when the library has completed its power-on self-test (POST) and initialization. This process ta
ページ20に含まれる内容の要旨
APCC.book Page 20 Tuesday, March 9, 2010 4:25 PM 1 Power supply power switch Getting Started 1 Configure your library using the Setup Wizard. For details, see the Dell™ PowerVault™ ML6000 Tape Library User’s Guide. 2 Verify that each host can communicate with the library’s tape drives. For details, see your host application documentation. 20 Dell PowerVault ML6000 Getting Started Guide
