ページ1に含まれる内容の要旨
M40S Series
HM020GI
Model:
HM040HI
HM060II
HM080JI
manual
HARD DISK DRIVE service
Hard Disk Drive Contents
1. Specification summary
2. Block Diagram of HDD
3. Connector & Jumper Pin Assignments
4. How to check if HDD is working
5. Exploded View
6. Maintenance Cylinder Configuration
7. How to use HUTIL Program
8. How to progress Burn-In Test
9. Caution
Attachment 1. The basic information
related HDD
Attachment 2. HDD related terms
Attachment 3. Q&A
ページ2に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE 1. Specification Summary Items Specification Remarks Voltage Requirement DC +12V/ ±10%, DC +5V/ ±5% Interface Serial ATA 1 .5Gbps HM020GI - 20.0GB (1CH) HM040HI - 40.0GB (2CH) Capacity UDMA133supporting HM060II - 60.0GB (3CH) HM080JI - 80.0GB (4CH) HM020GI - 1 Disk / 1 Head HM040HI - 1 Disk / 2 Head Disk / Head HM060HI - 2 Disk / 3 Head HM060HI - 2 Disk / 4 Head S.M.A.R.T C ompliant Features Buf fer size 8 M b y tes MTB F (POH) 5 50,000 hours TracktoTrack:0.8/1.0ms Seek T
ページ3に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE 2. Block Diagram of HDD PREAMP & READ/WRITE WRITE DRIVER CHANNEL IC Marvell Marvell 88C6590 G214M HDA A CUSTOMIZED IC including T SPINDLE MOTOR & AT CONTROLLER, EMBEDDED A ACTUATOR COMBO SERVO CONTROLLER, DSP DRIVER PROCESSOR, ADC & DAC B TLS2502 Dual-DSP 88I6525 U Internal Flash Ron S 1.5Mbit Buffer 64Mbit K4S641632H-UC60 HDD HDA (HEAD DISK A SSEMBL Y) PCBA (PCB ASSEMB LY) -HEAD -PCBA -DISK - VC M (Voi ce Coi l Moto r) - SP M (Spi ndle M otor) 3 M40S
ページ4に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE 5V 입력 5V SPINDLE MOTOR & ACTUATOR COMBO Buffer 3. 3V DRIVER FET 64Mbit TLS2502 K4S64163 2H-UC60 -3V 1. 2V Channel IC & HDC 88i6525 18pin Connector 4 M40S
ページ5に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE 3. Connector / Jumper Pin Assignment ● Serial Connector Interface Signals Pin Function Definition Data S1 Ground Ground Signal S2 Rx+ Differential Signal Pair Connection S3 Rx- Differential Signal Pair S4 Ground Ground S5 Tx+ Differential Signal Pair S6 Tx- Differential Signal Pair S7 Ground Ground Key and Spacing separate signal and power segment. Power P1 V33 3.3V Management P2 V33 3.3V P3 V33 3.3V P4 Ground Ground P5 Ground Ground P6 Ground Ground P7 V5 5V P8 V5 5V P9
ページ6に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE 4. Exploded View 6 M40S
ページ7に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE << Major c omponents of H DD >> HDD is formed by major components as follows: Base, Cover, ARM(E-Block), L atch, Crash Stop, Pivot Bearing, Breather Filter, Window Clock, Window Push Pin, Jump Pin, S pindle Motor, Actuator, Magnetic Head, Magnetic Disk, PCBA 1 Base Base could be a basic frames for HDD assembly. Spindle motor, ARM, VCM, cover and PCBA are assembled on it, and other components are sub-assembled on those confi guration. ARM and Spindle motor assembled to Hea
ページ8に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE 6 Pivot Bearing Pivot bearing is a roll bearing fixed the center of gyration of ARM. Inner Ra ce is fixed by screw after being connected to Base pivot and outer Race is fixed by retaini ng ring after being connected by ARM's hole and make the ARM's revolving movement active ly. 7 Breather Filter In the interior of HDD, air flow is formed by the spinning disk in high speed a nd pressure distribution occurred. This pressure is lower than atmospheric pressure of the exterior
ページ9に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE put power on and no matter what HDD read or write data,spindle motor always r evolve. Besides accurate reading from the media point of view is possible when main tain the constant speed within 0.1%,rotation error. The control circuit of spindle motor re ceive the index data from the spindle motor or media at every spin and check whether constant spe ed persists or not then revise the speed. Spindle motor is applied to DC brushless motor. 12 Actuator Hard disk has 2 disks
ページ10に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE 6. Maintenance Cylinder Configuration File Name Cyl Sector Size Ref ID Descriptions FSI 0 1 1 File System Information record FSI2 Backup copy of FSI FIT 0 2 4 File Information Table FIT2 Backup copy of FIT MLIST 0 6 1 M_LIST Maintenance Cylinder Defect List SV_TBL 0 7 4 SVOTBL Servo Table CONFIG2 0 12 2 CONFIG2 System Configuration Data CONFIG 1 1 2 CONFIG System Configuration Data SERIALNO 1 3 2 SERNUM Serial Number BI_SCRPT 1 5 4 BISCRT Burn-In Script BI_RESLT 1 10 1 BI
ページ11に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE ※ Explanation of terms for HDD repairing CONTENTS SYMPTOMS Motor doesn't drive. When HDD power on, LED is in on and motor Led is still on/off mode when power on NOT READY starttodrive.Atthistime headmake : PCB failure (NR) vibration and start to drive then stop the Led is still in on mode and doesn't vibration and led is off at the same time. make any vibration. DISK DEFECT Symptoms for damage at disk side ID,MD,OD failure is occurred in ID Defect is occurred at the inner
ページ12に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE 7. How to use HUTIL Program 1) Before you start HUTIL support from Voyager11P to PALO series.(HUTIL 1.12 version) (HUTIL has been upgrading constantly whenever new model comes out.) - Preparation before use Diskette or HDD containing HUTIL.EXE should be boot-up to MS-DOS mode,that is, should be contained IO.SYS, MSDOS.SYS,COMMAND.COM (IO.SYS, MSDOS.SYS: hidden file). And also HUTIL.CFG is required. 2) Explanation of each menu [TEST] SHORT TEST Menu for random read test, n
ページ13に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE BURN IN Download burn-In script to HDD. ERASE & SCAN Write full surface with 00 pattern and scan full surface. OD SCRATCH TEST Check OD for OS area has physical problem. AV SCAN TEST scan full surface every 256 Sectors and check elapsed time. [INFORMATION] NEW DEFECT LIST View the error list in memory. NEW DEFECT MAP Show defect on drive in graphic mode. These defects are invisible because of done then these are added after defect free done B/I & Read test or Auto test se
ページ14に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE DCO SET MAX ADDRESS Control Max Address with DCO Command. a) PROCESS Change Max Address to designated size.. b) TARGET LBA Set Max Address size with LBA. c) TARGET SIZE Set Max Address size with MB d) RECOVER NATIVE SIZE Recover to original size e) DISPLAY CURRENT STATUS Show Current Size and Original size C. ERASE HDD Erase all data in Drive. Write with 00 pattern a) PROCESS Execute Erase Drive b) TARGET LBA Set Erase size with LBA c) TARGET SIZE Set Erase size with MB.
ページ15に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE F. SELF DIAGNOSTIC diagnostic for end user G. CHANGE NATIVE SIZE Control Drive size with VU Set Max Command a) CHANGE NATIVE SIZE Change Native Size as designated. b) TARGET LBA SetNativeSizewithLBA c) F/W REVISION Change Firmware revision except first 2 charactor. d) MODEL NAME Change model name, 'SAMSUNG' should be on model name, because hutil uses model name it is samsung drive or not. e) RECOVER ORIGINAL SIZE Recover to original Native Size. f) DISPLAY CURRENT STATUS
ページ16に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE Version of HUTIL. DOS SHELL Execute DOS Shell. If you want back to HUTIL, input EXIT. DRIVE INFORMATION Open the information window about the target HDD. Press ESC to close. EXIT TO DOS End HUTIL program. 3) The others - Difference of read test and auto test (Difference from HUTIL user, refer to supplement ) ① How to Read All/From Test: In "read all test" case, only show error status on screen not to progress D/F(defect free) but to read. This method is available for test
ページ17に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE 3 times per region. ( Judge failure by reading not the whole cylinder but servo sector only because it is apt to mistake failure to head failure due to scratch) ② PES Check (PES, RCO, Mechanism) : Compare PES value from the first cylinder starting OD(except MC ),MD,ID region to the 3rd → cylinder. (Check 30 times per 1 cylinder) Remark "failure" when error occurred more than 3 times per 1 cylinder. ③ Maintenance Cylinder Check(M/C): Read Maintenance cylinder from the numb
ページ18に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE ② Example of disk failure < Error List > CYL HD(Head) SEC Error List 1 0 117 ECC Err 2 1 106 Data Am Not Found 3 1 110 ECC Err 42 12 ECCErr 117 1 13 ECC Err 120 2 152 ECC Err 159 3 102 ECC Err 170 1 171 1 172 3 173 1 174 2 190 2 191 1 Most of case,defects(cylinder)are sporadic or continuous but if defects are partly -continuous, disk could be judged disk failure. It is called the continuous defects "scratch" it means that head is scratched the disk side in the direction o
ページ19に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE ③ Example for Head related failure < Error List > CYL HD(Head) SEC Error 1 1 117 ECC Err 2 1 106 Data Am Not Found 3 1 110 ECC Err 41 12 ECCErr 51 13 ECCErr 6 1 152 ECC Err 7 1 102 ECC Err 81 91 10 1 11 1 12 1 13 1 14 1 Compared with disk failure,head related failure occur in particular HD(head) from the first cylinder and this is occurred continuously.(it is occurred in two more heads) If failure is continuous, we are confused if it is head failure or disk failure. At th
ページ20に含まれる内容の要旨
SAMSUNG HARD DISK DRIVE HUTIL Test Flow/Error Code Codes marked as red among broken codes are displaying automatically in HUTIL Program! Label error [AJ44] Label damaged [AJ45] PCBA ERROR N> Appearance PCBA burnt [AJ12] HDA ERROR PCBA ding,break [AJ13] HDA ding,scratch [AJ32] PCBA Y exchange HDA PCBA No spin [AJ35] PCBA Not ready [AJ36] PCBA ERROR Power Test HDA No spin [AJ33] HDA ERROR N> HDA Not ready [AJ34] Y ROM failure [AJ39] AUTO TEST PCBA&HDA failure [AJ46] START ↓ MOTOR Noise [AJ37] HEAD
