ページ1に含まれる内容の要旨
TWO HUNDRED
USER’S MANUAL
ページ2に含まれる内容の要旨
TABLE OF CONTENTS INTRODUCTION 1.1 Case Specifications.…..………………………………………………………………………………….. 3 1.2 Diagram…………………………………………………………………….…………………………………. 3 HARDWARE INSTALLATION GUIDE 2.1 Setting Up….…………………………………………………………………………………………………. 4 2.2 Power Supply Installation……………………………………………………………………………… 4 2.3 Cable Management………………………………………………………………………………………. 5 2.4 Motherboard Installation..……………………………………………………………………………. 5 2.5 Internal 3.5” Device Installation……………………………………………………………………. 6 2.6 F
ページ3に含まれる内容の要旨
TWO HUNDRED USER’S MANUAL At Antec, we continually refine and improve our products to ensure the highest quality. It’s possible that your new case will differ slightly from the descriptions in this manual. This isn’t a problem; it’s simply an improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are correct. Disclaimer This manual is intended only as a guide for Antec’s computer enclosures. For more comprehensive instructions on ins
ページ4に含まれる内容の要旨
1.1 CASE SPECIFICATIONS Case Type Gaming Mid Tower Color Black Dimensions 450mm (H) x 200mm (W) x 470mm (D) 17.7” (H) x 7.9” (W) x 18.5” (D) Weight 13.9 lbs / 6.3 kg Cooling 1 x Rear 120mm TwoCool™ fan 1 x Top special 140mm TwoCool™ fan 2 x Front 120mm fan mounts (optional) 1 x Side 120mm fan mount (optional) Drive Bays 10 Drive Bays: - 3 x External 5.25” drive bays - 1 x External front-loaded hot swap 3.5” SATA hard drive caddy - 6 x Internal 3.5” drive bays Expansion Slots
ページ5に含まれる内容の要旨
HARDWARE INSTALLATION GUIDE 2.1 SETTING UP 1. Place the case upright on a flat, stable surface with the rear of the case facing you. 2. Remove the side panels by first removing the thumbscrews at the rear of the case. Then, grip each panel at the top and bottom and slide it toward the rear of the case until it detaches from the chassis. 3. To remove the front bezel, locate the three plastic tabs on the left side of the bezel. They fasten the front bezel to the metal chassis. R
ページ6に含まれる内容の要旨
2.3 CABLE MANAGEMENT There is a cable management compartment behind the 3.5” drive cage. You can tuck or route excess cables in this compartment. 1. Open the right side panel as described in section 2.1. 2. Locate the cable management compartment with cable ties located behind the walls of the 3.5” drive cage. 3. Tuck or route your excess cables to the compartment. This will keep the cables from interfering with airflow in your case and help with cooling. 4. Use the cable ties
ページ7に含まれる内容の要旨
2.5 INTERNAL 3.5” DEVICE INSTALLATION The Two Hundred provides space for up to six 3.5” hard drives. Before you begin, remove the side panels and front bezel of the case as described in section 2.1. Behind the front bezel there is a fan cage which provides space for up to two fans at the front of the case. 1. Open the fan cage by pressing both clips to release it, then swing it open and detach it from the chassis. 2. Insert your 3.5” device into the 3.5” drive cage from the front
ページ8に含まれる内容の要旨
2.7 EXTERNAL 5.25” DEVICE INSTALLATION There are three externally accessible 5.25” drive bays. Before you begin, remove both side panels and front bezel as detailed in section 2.1. 1. Remove the drive bay faceplate by applying pressure to the inside of the plate until it pops free of the bezel. 2. Slide your 5.25” device into the bay from the front of the case. 3. Secure the drive into position in the drive cage using the provided screws. 4. Mount any other 5.25” devices accor
ページ9に含まれる内容の要旨
You can connect either the AC’97 or the HDA connector, depending on your motherboard. Locate the internal audio connectors from your motherboard or sound card and connect the corresponding audio cable. Consult your motherboard or sound card manual for the pin-out positions. Even if your system supports both standards, only use one connector. 3.3 POWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS Connected to your front panel are LED and switch leads for power, reset, and
ページ10に含まれる内容の要旨
COOLING SYSTEM 4.1 TWOCOOL™ FANS Rear TwoCool™ Fan – There is a 120 x 25mm TwoCool™ fan preinstalled at the rear of the case. The fan is installed so the air will be blown out of the case. This fan comes with a two-speed switch that let you choose the speed best suited to your need. The default fan speed setting is Low. 120mm TwoCool™ Specifications Size: 120 x 25mm TwoCool™ fan Rated Voltage: 12V Operating Voltage: 10.8V ~ 13.2 V Speed Input Static Acoustic Input Airf
ページ11に含まれる内容の要旨
Note: The minimum voltage to start a typical TwoCool™ fan is 5V. We recommend that you set the fan speed to High if you choose to connect the fan(s) to a fan control device or to the Fan- Only connector found on some Antec power supplies. A fan control device regulates the fan speed by varying the voltage, which may start as low as 4.5V to 5V. Connecting a TwoCool™ fan set on Low to a fan-control device may result in the fan not being able to start because the already lowered voltage from th
ページ12に含まれる内容の要旨
4.3 WASHABLE AIR FILTERS Occasionally, it will be necessary to wash the air filters. Not washing the filters may result in high system temperatures and possible stability problems. We recommend checking the air filters at least once a month initially. The frequency will change depending on environmental conditions and system usage. Users who run their systems 24/7 will have to check their filters more often than those who don’t run their systems every day. Front Air Filter – There is a
ページ13に含まれる内容の要旨
Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 USA tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rotterdam Netherlands tel: +31 (0) 10 462-2060 fax: +31 (0) 10 437-1752 Customer Support: US & Canada 1-800-22ANTEC customersupport@antec.com Europe +31 (0) 10 462-2060 europe.techsupport@antec.com www.antec.com © Copyright 2009 Antec, Inc. All rights reserved. All trademarks are the property of their
