ページ1に含まれる内容の要旨
Modular MSOP8 EVM
User’s Guide
September 2003 Data Acquisition
SLAU115
ページ2に含まれる内容の要旨
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the t
ページ3に含まれる内容の要旨
EVM IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not considered by TI to be fit for commercial use. As such, the goods being provided may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety measures typically found in the end product
ページ4に含まれる内容の要旨
EVM WARNINGS AND RESTRICTIONS It is important to operate this EVM within the input voltage range of 1.8 VDC to 5 VDC and the output voltage range of 0 VDC and 5 VDC. Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions concerning the input range, please contact a TI field representative prior to connecting the input power. Applying loads outside of the specified output range may result in unintended operation and/or poss
ページ5に含まれる内容の要旨
Preface Read This First About This Manual This user’s guide describes the characteristics, operation, and use of the Modular MSOP8 EVM. This EVM is a multi-device, 12 to 16 bit, SSI, analog to digital converter Evaluation Module. A complete circuit description, as well as schematic diagram and bill of materials, are included. How to Use This Manual This document contains the following chapters: Chapter 1—EVM Overview Chapter 2—Analog Interface Chapter 3—Digital Interface Chapter 4—Power Supplies
ページ6に含まれる内容の要旨
The information in a caution or a warning is provided for your protection. Please read each caution and warning carefully. Related Documentation From Texas Instruments To obtain a copy of any of the following TI documents, call the Texas Instruments Literature Response Center at (800) 477-8924 or the Product Information Center (PIC) at (972) 644-5580. When ordering, identify this booklet by its title and literature number. Updated documents can also be obtained through our website at www.ti.com.
ページ7に含まれる内容の要旨
Contents 1 EVM Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 2 Analog Interface . . . . . . . . . . .
ページ8に含まれる内容の要旨
-2
ページ9に含まれる内容の要旨
Chapter 1 EVM Overview The following section gives a general overview of the Modular MSOP8 evaluation board. Topic Page 1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 EVM Overview 1-1
ページ10に含まれる内容の要旨
Features 1.1 Features Full-featured evaluation board for a variety of single channel, eight pin Mi- cro SOP, 12 and 16-bit, serial Output, analog to digital converters On-board reference and buffer circuits High-speed serial interface Modular design for use with a variety of DSP and micro controller interface boards 1.2 Introduction The Modular MSOP8 Evaluation Module is an updated version of the Burr-Brown DEM-MSOP8 evaluation board. The EVM is designed so that a single printed wiring board (PW
ページ11に含まれる内容の要旨
Chapter 2 Analog Interface For maximum flexibility, the Modular MSOP8 EVM is designed for easy interfacing to multiple analog sources. Samtec part numbers SSW-110-22-F-D-VS-K and TSM-110-01-T-DV-P provide a convenient 10-pin dual row header/socket combination at J1. This header/socket provides access to the analog input pins of the ADC. Consult Samtec at www.samtec.com or call 1-800-SAMTEC-9 for a variety of mating connector options. Table 2-1.Analog Interface Pin Out Pin Number Signal Descrip
ページ12に含まれる内容の要旨
2-2
ページ13に含まれる内容の要旨
Chapter 3 Digital Interface The Modular MSOP8 EVM is designed for easy interfacing to multiple control platforms. Samtec part numbers, SSW-110-22-F-D-VS-K and TSM-110-01-T-DV-P, provide a convenient 10-pin dual row header/socket combination at J2. This header/socket provides access to the digital control and serial data pins of the MSOP8 EVM. Consult Samtec at www.samtec.com or 1-800-SAMTEC-9 for a variety of mating connector options. Table 3-1.Digital Interface Pin Out Pin Number Signal Descr
ページ14に含まれる内容の要旨
3-2
ページ15に含まれる内容の要旨
Chapter 4 Power Supplies The Modular MSOP8 EVM board requires 5 V dc for the analog section. This includes the voltage reference (U2), the reference buffer (U4), and optionally, the ADC installed on the EVM (via JMP1). Supply voltages of 1.8 V to 5 V dc for the digital section are also required. When used in combination with one of the DAP Interface boards, J3 provides connection to the common power bus described in document SLAU104. Table 4-1 shows the pin out of J3. Table 4-1.Power Supply Pi
ページ16に含まれる内容の要旨
ADC Power 4.1 ADC Power The device installed on the modular MSOP8 EVM has several options in regards to its power source. Refer to the schematic for the following discussion. JMP1 and JMP3 allow the user to select the power supply used by the ADC. When JMP1 is in the default factory position (Shunt on pins 1-2), power to the ADC comes from J3.3 or TP5. Single gate digital buffers (U3, U5, and U6) are installed on the ADC’s digital input/output lines to allow operation with low voltage controller
ページ17に含まれる内容の要旨
Chapter 5 EVM Operation The following section provides information in the analog input, digital control, and general operating conditions of the Modular MSOP8 EVM. Topic Page 5.1 Analog Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 5.2 Digital Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 5.3 Chip Select (Shut Down) . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ18に含まれる内容の要旨
Analog Input 5.1 Analog Input The analog input source can be applied directly to J1 (top or bottom side) or through optional amplifier and signal conditioning modules. The analog input range is dependent on the configuration of the EVM and the ADC installed at location U1. Consult the datasheet for the device to determine the maximum analog input range. 5.2 Digital Control The digital control signals can be applied directly to J2 (top or bottom side). The modular MSOP8 EVM can also be connected
ページ19に含まれる内容の要旨
Chapter 6 EVM BOM and Schematic The following table contains a complete bill of materials for the modular MSOP8 EVM bill of materials. Table 6-1.Bill of Materials Designators Description Manufacturer Mfg. Part Number C2 C3 C4 C13 Not Installed R11 Not Installed C1 0.47 µ F, 0805, ceramic, X7R, 25 V, 10% Panasonic ECJ-2YB1C474K C11 C12 C14 0.1 µ F, 0805, ceramic, X7R, 50 V, 10% Panasonic ECJ-2YB1H104K C6 C8 C10 10 µ F, 1206, ceramic, Y5V, 10 V, 10% Panasonic ECJ-3YF1A106Z C5 C14 C15 10 µ F, A c
ページ20に含まれる内容の要旨
EVM Schematic 6.1 EVM Schematic The schematic diagram is provided as a reference. 6-2
