ページ1に含まれる内容の要旨
MSI
MICRO-STAR INTERNATIONAL
MS-6382 (v2.X) Micro ATX Mainboard
Version 2.0
G52-MA00563
i
ページ2に含まれる内容の要旨
Manual Rev: 2.0 Release Date: March 2002 FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equip- ment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accor- dance with the in
ページ3に含まれる内容の要旨
Edition March 2002 Copyright Notice The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice. Trademarks All trademarks are the properties of their respective owners. ® ® Intel and Pentium are registered trademarks of Intel Corporation. ® PS/2 and
ページ4に含まれる内容の要旨
Safety Instructions 1. Read the safety instructions carefully. 2. Save this Users Guide for possible use later. 3. Keep this equipment away from humidity. 4. Lay this equipment on a stable and flat surface before setting it up. 5. The openings on the enclosure are used for air convection and to prevent the equipment from overheating. Note: Do not cover the openings. 6. Make sure that the power voltage is within its safety range and has been adjusted properly to the value of 110/220V before con
ページ5に含まれる内容の要旨
CONTENTS Chapter 1. Getting Started ........................................................................ 1-1 Mainboard Specification ...................................................................... 1-2 Mainboard Layout ............................................................................... 1-4 Quick Components Guide .................................................................... 1-5 Chapter 2. Hardware Setup .................................................................
ページ6に含まれる内容の要旨
Connectors ......................................................................................... 2-12 Floppy Disk Drive Connector: FDD1 ........................................... 2-12 Chassis Intrusion Switch Connector: J1 ...................................... 2-12 Hard Disk Connectors: IDE1 & IDE2 ........................................... 2-13 CD-In Connector: CD_IN ............................................................ 2-14 Aux Line-In Connector: AUX_IN ..........................
ページ7に含まれる内容の要旨
Advanced BIOS Features .................................................................... 3-8 Advanced Chipset Features............................................................... 3-12 Integrated Peripherals ........................................................................ 3-16 Power Management Setup ................................................................. 3-21 PNP/PCI Configurations ..................................................................... 3-26 PC Health Status
ページ8に含まれる内容の要旨
Getting Started Chapter 1. Getting Started 1 Getting Started The MS6382 v2.X Micro-ATX mainboard is a high performance computer mainboard based on VIA KT266A & VT8233A chipsets. The KT266A chipset is ideal for high quality and high integration desktop and notebook AGP/PCI/LPC computer systems based on Socket A processors. The VT8233A V-Link Client controller is a highly integrated PCI/LPC controller. It supports three PCI slots of arbitration and decoding for all integrated functions and LPC
ページ9に含まれる内容の要旨
Chapter 1 Mainboard Specification CPU ® TM TM Socket 462 (Socket A) for AMD Duron /Athlon processor with 200/ 266MHz FSB Support 600MHz up to 1.5GHz processor Chipset ® VIA KT266A Chipset - Support 66MHz V-Link Host interface with peak bandwidth of 266MB/s - Advanced ECC memory controller supporting PC133/PC100 SDR SDRAM and PC2100/1600 DDR SDRAM - Full featured AGP Controller: AGP v2.0 compliant ® VIA VT8233A Chipset - High bandwidth V-Link client controller - Integrated faster Ethernet co
ページ10に含まれる内容の要旨
Getting Started Audio 2 channels S/W Audio CODEC, Realtek ALC201A AC97s digital link controller was integrated in VIA VT8233A On-Board Peripherals On-Board Peripherals include: - 1 floppy port supports 2 FDD with 360K, 720K, 1.2M, 1.44M and 2. 88Mbytes. - 2 serial ports (COMA + COM B) - 1 parallel port supports SPP/EPP/ECP mode - 4 USB ports (2 x Rear / 2x Front) - 1 Audio/Game port - 1 optional RJ-45 LAN jack (Reaktek RTL8100BL) BIOS The mainboard BIOS provides Plug & Play BIOS which detect
ページ11に含まれる内容の要旨
Chapter 1 Mainboard Layout Top : mouse CFAN1 Bottom: keyboard SOCKET 462 Top: LAN Jack Bottom: USB ports Winbond W83697HF J1 Top : Parallel Port Bottom: COM A COM B VIA KT266A Top : Game port CD_IN Bottom: Line-Out Line-In Mic AUX_IN AGP Slot MODEM_IN PCI Slot 1 RTL 8100BL SW1 VT8233A PCI Slot 2 BATT JGS1 Codec + PCI Slot 3 ALC201A SFAN1 JFP2 USB1 JAUD1 JBAT1 FPIR CNR JGL1 JFP1 MS-6382 v2.X Micro ATX Mainboard 1-4 ATX Power Supply DDR 1 DDR 2 BIOS IDE 1 FDD 1 IDE 2
ページ12に含まれる内容の要旨
Getting Started Quick Components Guide Component Function Reference JWR1 ATX 20-pin Power Connector See p. 2-6 USB Connectors Connecting to USB devices See p. 2-8 COM A & B Connector Connecting to Serial ports See p. 2-9 Game/Audio Connectors Connecting to Game/Audio devices See p. 2-9 LPT1 Parallel port connector See p. 2-10 RJ-45 LAN Jack Connecting to LAN devices See p. 2-11 FDD1 Floppy disk drive connector See p. 2-12 J1 Chassis intrusion switch See p. 2-12 IDE1~ IDE2 Hard disk connectors Se
ページ13に含まれる内容の要旨
Hardware Setup Chapter 2. Hardware Setup 2 Hardware Setup This chapter provides you with the information about hardware setup procedures. While doing the installation, be careful in holding the components and follow the installation procedures. For some components, if you install in the wrong orientation, the components will not work properly. Use a grounded wrist strap before handling computer components. Static electricity may damage the components. TOPICS Central Processing Unit: CPU 2-2 Mem
ページ14に含まれる内容の要旨
Chapter 2 Central Processing Unit: CPU ® TM TM The mainboard supports AMD Duron /Athlon processor. The mainboard uses a CPU socket called Socket-462 for easy CPU installation. When you are installing the CPU, make sure the CPU has a heat sink and a cooling fan attached on the top to prevent overheating. If you do not find the heat sink and cooling fan, contact your dealer to purchase and install them before turning on the computer. CPU Installation Procedures Open Lever 1. Pull the lever sidewa
ページ15に含まれる内容の要旨
Hardware Setup Thermal Issue for CPU As processor technology pushes to faster speeds and higher performance, thermal management becomes increasingly crucial when building computer systems. Maintaining the proper thermal environment is key to reliable operation. As such, the processor must be maintained in the specified thermal requirements. AMD recommends the use of high performance thermal inter- face material. AMD Athlon processor with a speed of 600MHz and above requires LARGER heatsink a
ページ16に含まれる内容の要旨
Chapter 2 Memory The mainboard provides 2 slots for 184-pin, 2.5V unbuffered DDR DIMM with 4 memory banks. You can install PC1600 or PC2100 DDR SDRAM mod- ules on the DDR DIMM slots (DDR 1~2). To operate properly, at least one DIMM module must be installed. Note: The DDR DIMM slots DO NOT support PC2700 modules. Introduction to DDR SDRAM DDR (Double Data Rate) SDRAM is similar to conventional SDRAM, but doubles the rate by transferring data twice per cycle. It uses 2.5 volts as opposed to 3.3 v
ページ17に含まれる内容の要旨
Hardware Setup DDR Module Combination You can install either single sided or double sided 184-pin DDR DIMM modules into DDR DIMM slots to meet your needs. Different from the SDR DIMM, the DDR DIMM has only one notch on the center of module. The number of pins on either side of the breaks are different. The module will only fit in the right orientation. You can install memory modules in any combination as follows: Slot Memory Module Total Memory Slot 1 64MB, 128MB, 64MB~1GB (Bank 0 & Bank 1)
ページ18に含まれる内容の要旨
Chapter 2 Power Supply The mainboard supports ATX power supply for the power system. Be- fore inserting the power supply connector, always make sure that all compo- nents are installed properly to ensure that no damage will be caused. ATX 20-Pin Power Connector: JWR1 This connector allows you to connect to an ATX power supply. To connect to the ATX power supply, make sure the plugs of the power supply is inserted in the proper orientation and the pins are aligned. Then push down the power supply
ページ19に含まれる内容の要旨
Hardware Setup Back Panel The Back Panel provides the following connectors: LAN Parallel Midi/Joystick (optional) Mouse Keyboard COM A L-out L-in MIC COM B USB Mouse Connector ® The mainboard provides a standard PS/2 mouse mini DIN connector for ® ® attaching a PS/2 mouse. You can plug a PS/2 mouse directly into this connector. The connector location and pin assignments are as follows: Pin Definition PIN SIGNAL DESCRIPTION 6 5 1 Mouse DATA Mouse DATA 4 3 2 NC No connection 3 GND Ground 4 VCC +5
ページ20に含まれる内容の要旨
Chapter 2 Keyboard Connector ® The mainboard provides a standard PS/2 keyboard mini DIN connector ® ® for attaching a PS/2 keyboard. You can plug a PS/2 keyboard directly into this connector. Pin Definition PIN SIGNAL DESCRIPTION 6 5 1 Keyboard DATA Keyboard DATA 3 2 NC No connection 4 3 GND Ground 4 VCC +5V 1 2 5 Keyboard Clock Keyboard clock PS/2 Keyboard (6-pin Female) 6 NC No connection USB Connectors The mainboard provides a UHCI (Universal Host Controller Interface) Universal Serial Bu
