ページ1に含まれる内容の要旨
iSeries 270 and 820
30xx Memory
Card Installation
Version 5
SENG-3002-01
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
iSeries 270 and 820 30xx Memory Card Installation Version 5 SENG-3002-01
ページ4に含まれる内容の要旨
Note Before using this information and the product it supports, be sure to read the “Safety and Environmental Notices” on page iii and the “Notices” on page 19. Second Edition (May 2001) This edition applies only to reduced instructions set computer (RISC) systems. © Copyright International Business Machines Corporation 2000, 2001. All rights reserved. US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp.
ページ5に含まれる内容の要旨
Safety and Environmental Notices Danger Notices A danger notice calls attention to a situation that is potentially lethal or extremely hazardous to people. DANGER To prevent a possible electrical shock during an electrical storm, do not connect or disconnect cables or station protectors for communications lines, display stations, printers, or telephones. (RSFTD003) DANGER To prevent a possible electrical shock from touching two surfaces with different electrical grounds, use one hand, when possi
ページ6に含まれる内容の要旨
Product Recycling and Disposal Components of the system, such as structural parts and circuit cards, can be recycled where recycling facilities exist. IBM does not currently collect and recycle used IBM products from customers in the United States other than those products that are involved in trade-in programs. Companies are available to disassemble, reutilize, recycle, or dispose of electronic products. Contact an IBM account representative for more information. The system unit contains batter
ページ7に含まれる内容の要旨
Installation Instructions Before you begin __ 1. Take a minute to become familiar with these instructions. Note that you may not complete every step in this instruction. __ 2. These instructions contain steps on how to install memory (main storage cards), including adding another 2884 card assembly, into the system unit. __ 3. This feature is customer installed. The installation of this feature is intended for an experienced user who understands industry terminology and who has some system exper
ページ8に含まれる内容の要旨
__ 9. If you encounter difficulties during the installation, contact your authorized dealer or service provider. Powering off the system unit __ 1. Set the System performance adjustment to a value other than option 0. __ a. On an iSeries command line, type WRKSYSVAL (QPFRADJ) and press Enter. __ b. Select the Change option on the Work with System Values display and press Enter. __ c. If you have a Performance adjustment value of option 1, option 2,or option 3 you do not need to change the value.
ページ9に含まれる内容の要旨
Figure 1. Location of Access Cover __ 1. Do you have a 270 system unit? Yes No ↓ You have a 820 system unit. Go to step 5 on page 4. __ 2. Does your system unit have an access cover as shown in Figure 1 A? Yes No ↓ The memory is located on the inside of your 270 system unit. Go to “Installing memory cards inside your system unit” on page 7. __ 3. Remove the access cover. Note: A customer can safely use all latches that are colored blue. __ 4. Figure 2 on page 4 shows the location of the 2884 c
ページ10に含まれる内容の要旨
Figure 2. Location of card assembly 2884 in a 270 system unit __ 5. Do you have a new 2884 card assembly to install in your 820 system unit? Yes No ↓ Go to step 7 on page 5. __ 6. Remove the empty card assembly C . 4 30xx Memory Card Installation V5R1
ページ11に含まれる内容の要旨
Figure 3. Location of Card Assembly 2884 in 820 Unit __ 7. Remove the 2884 card assembly B or C from the system unit by doing the following: __ a. Unlatch the two blue latches on the 2884 until the card assembly slightly “pops” out. __ b. Pull on both latches at the same time to remove the card assembly from the system unit. __ c. Turn the card assembly over and lay it on the static protective bag provided. Adding memory to the card assembly __ 1. Before you remove the blank filler cards and
ページ12に含まれる内容の要旨
Figure 4. Memory Locations on Card Assembly __ 2. Remove the blank filler cards from the next available positions by doing the following: __ a. Push outward on the latches A that are located at each end of the filler card, Figure 5 on page 7. __ b. Remove the filler card from the card socket and discard it. __ 3. Find the package that contains the new memory cards. __ 4. Attention: Memory cards are fragile. Handle with care. Remove a memory card, one at a time, from the static protective packa
ページ13に含まれる内容の要旨
Figure 5. Install Memory Cards __ 6. Install the remaining memory cards. __ 7. When you finish installing all the memory cards, turn the card assembly over, and slide it into the system unit. Push on both card latches at the same time. Close the latches when you cannot push the card assembly any further into the system unit. __ 8. Reinstall the access cover. __ 9. You have completed the installation of the memory cards in your system. Go to “Installing system unit covers” on page 10. Installing
ページ14に含まれる内容の要旨
Figure 6. Memory Connectors View 1 8 30xx Memory Card Installation V5R1
ページ15に含まれる内容の要旨
Figure 7. Memory Connectors View 2 __ 2. Refer to the figure that matches your system unit to place the memory in the correct order. __ 3. Place memory cards as follows on the processor: v In pairs, beginning with C and D, then E and F, and so on. v Each pair of storage cards must be either 128MB, 256MB, or 512MB. __ 4. Remove the blank filler cards from the next available positions by doing the following: __ a. Push outward on the latches that are located at each end of the filler card, Figure
ページ16に含まれる内容の要旨
__ 8. Install the second memory card. __ 9. Do you have any other adapter cards or devices to install? No Yes ↓ If you have another device such as an adapter card, a tape unit, or disk units to install, go to the instructions that came with that device. Go to “Installing system unit covers”. Installing system unit covers __ 1. Remove the wrist strap. __ 2. Figure 8 shows how to install the system unit side cover by aligning the tabs on the top and bottom edge. Press forward to make sure that all
ページ17に含まれる内容の要旨
__ 4. DANGER An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the system or the products that attach to the system. It is the customer’s responsibility to ensure that the outlet is correctly wired and grounded to prevent an electrical shock. (RSFTD201) Plug the following power cords into an electrical outlet. v System unit Note: Do not power on your system unit at this time. v System unit console __ 5. Plug in and power on all attached devices, suc
ページ18に含まれる内容の要旨
__ a. Press the Mode Select button until the Manual mode indicator (a small hand) lights up. __ b. Press the Increment/Decrement push button until 02 appears in the Function/Data display. __ c. Press the Enter push button on the control panel. __ d. Press the Increment/Decrement push button until B appears in the Function/Data display. __ e. Press the Enter push button on the control panel. __ f. Press the Increment/Decrement push button until S appears in the Function/Data display. __ g. Press
ページ19に含まれる内容の要旨
Note: If the status is not Operational, check the memory cards. __ g. If you have a printer, print the configuration list. Note: To print the hardware resources list, press F12 one time. When the Logical Hardware Resources menu appears, press F6. __ h. To return to the Main Menu, press F3 three times and then press Enter. __ 10. If you changed the System performance adjustment option value in step 1 on page 2, do the following to return to what you had prior to your upgrade: __ a. On an iSeries
ページ20に含まれる内容の要旨
14 30xx Memory Card Installation V5R1
