ページ1に含まれる内容の要旨
USER MANUAL
EN-7230
ページ2に含まれる内容の要旨
Remove fan housing by using thumbs to Series EN-7230 unfasten clips and place fan in housing (Fig 5). ***Important-First please check your model number before proceeding. The user Snap fan housing back into the chassis. manual is set up to correspond to the model number and installation will vary depending on the model. Connect fan and speaker wiring to M/B as instructed in M/B user manual Required tools: Phillips head screwdriver, pliers (After M/B is installed!). ***(Photos shown may
ページ3に含まれる内容の要旨
Remove fan housing by using thumbs to Series EN-7230 unfasten clips and place fan in housing (Fig 5). ***Important-First please check your model number before proceeding. The user Snap fan housing back into the chassis. manual is set up to correspond to the model number and installation will vary depending on the model. Connect fan and speaker wiring to M/B as instructed in M/B user manual Required tools: Phillips head screwdriver, pliers (After M/B is installed!). ***(Photos shown may
ページ4に含まれる内容の要旨
**Depending on M/B, you might have Three pc. Cover To remove drive cassette** Reinstall top cover making sure to line up A. Identify if M/B is AT, ATX or microATX. tabs on back (Fig.12). Then install side B. Place chassis on its side with electronic panels by placing on rail guides (Fig.13), and sliding towards back of chassis. Use Bay in view (Fig. 9) hex screws to fasten side panels in place. C. Using your choice of standoffs or stakes to fasten M/B, p
ページ5に含まれる内容の要旨
**Depending on M/B, you might have Three pc. Cover To remove drive cassette** Reinstall top cover making sure to line up A. Identify if M/B is AT, ATX or microATX. tabs on back (Fig.12). Then install side B. Place chassis on its side with electronic panels by placing on rail guides (Fig.13), and sliding towards back of chassis. Use Bay in view (Fig. 9) hex screws to fasten side panels in place. C. Using your choice of standoffs or stakes to fasten M/B, p
ページ6に含まれる内容の要旨
Snap into place, starting with top snaps. Make sure tabs at top of bezel are in place in holes at top of chassis, then push lower 2 4 half of bezel into place 1 19 Fig:15 3 Option 3.5"HDD 5 6 20 18 7 9 8 17 16 15 14 11 13 12 10
ページ7に含まれる内容の要旨
Snap into place, starting with top snaps. Make sure tabs at top of bezel are in place in holes at top of chassis, then push lower 2 4 half of bezel into place 1 19 Fig:15 3 Option 3.5"HDD 5 6 20 18 7 9 8 17 16 15 14 11 13 12 10
ページ8に含まれる内容の要旨
Part List EN-7230 SERIES P/N:36110341 NO P/N PART NAME 1 3213698 SUPPORT BRACKET 2 3213665 5.25”DRIVE BRACKET 3 3213643 CHASSIS 4 5207667 ADAPTER BRACKET(BABY AT,ATX) 5 3214577 ADAPTER PLATE 6 3213676 M/B MOUNTING PLATE 7 5208089 3.5”DRIVE BRACKET 8 3213654 COVER 9 3131445 CARD GUIDE BRACKET(A.B.S) 10 5103794 BEZEL(7230 ONLY) 11 5404613 CONTROL CONNECTOR(A) 12 3132596 POWER SWITCH HOLDER 13 3212514 3.5”EMI CLIP 14 3131467 RUBBER FOOT 15 5404624 CONTROL CONNECTOR(B) 16 *32140541
