ページ1に含まれる内容の要旨
Cisco ONS 15454 Installation and
Operations Guide
Product and Documentation Release 3.1
November 2001
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 526-4100
Customer Order Number: DOC-7813453=
Text Part Number: 78-13453-01
ページ2に含まれる内容の要旨
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE
ページ3に含まれる内容の要旨
CONTENTS About This Manual xxxiii Audience xxxiii Organization xxxiii Related Documentation xxxiv Conventions xxxv Obtaining Documentation xxxv World Wide Web xxxvi Optical Networking Product Documentation CD-ROM xxxvi Ordering Documentation xxxvi Documentation Feedback xxxvi Obtaining Technical Assistance xxxvii Cisco.com xxxvii Technical Assistance Center xxxvii Procedure: Contacting TAC by Using the Cisco TAC Website xxxvii Procedure: Contacting TAC by Telephone xxxviii CHAPTER 1 Hardware I
ページ4に含まれる内容の要旨
Contents Procedure: Open the Front Cabinet Compartment (Door) 1-12 Procedure: Remove the Front Door 1-13 1.5 Backplane Access 1-14 Procedure: Remove the Backplane Sheet Metal Covers 1-15 1.5.1 Lower Backplane Cover 1-15 Procedure: Remove the Lower Backplane Cover 1-16 1.5.2 Alarm Interface Panel 1-16 1.6 EIA Installation 1-17 1.6.1 BNC EIA 1-17 1.6.2 High-Density BNC EIA 1-18 1.6.3 SMB EIA 1-19 1.6.4 AMP Champ EIA 1-20 Procedure: Install a BNC, High-Density BNC, or SMB EIA 1-22 Procedure: Inst
ページ5に含まれる内容の要旨
Contents Procedure: Install DS-1 AMP Champ Cables on the AMP Champ EIA 1-43 1.12 Card Installation 1-44 1.12.1 Slot Requirements 1-45 Procedure: Install the TCC+ and XC/XCVT/XC10G Cards 1-47 Procedure: Install Optical, Electrical, and Ethernet Cards 1-48 Procedure: Install the AIC Card 1-49 1.12.2 Gigabit Interface Converter 1-50 Procedure: Install Gigabit Interface Converters 1-50 Procedure: Remove a Gigabit Interface Converter 1-52 1.13 Fiber-Optic Cable Installation 1-52 Procedure: Install
ページ6に含まれる内容の要旨
Contents 1.16.14 Power Specifications 1-67 1.16.15 Environmental Specifications 1-67 1.16.16 Dimensions 1-67 1.17 Installation Checklist 1-67 1.18 ONS 15454 Software and Hardware Compatibility Matrix 1-68 CHAPTER 2 Software Installation 2-1 2.1 Installation Overview 2-1 2.2 Computer Requirements 2-2 2.3 Running the CTC Setup Wizard 2-4 Procedure: Run the CTC Setup Wizard 2-4 Procedure: Set Up the Environment Variable (Solaris installations only) 2-4 Procedure: Reference the JRE (Solaris instal
ページ7に含まれる内容の要旨
Contents Procedure: Modify the Network or Domain Background Color 2-19 2.6.2.5 Changing the Network View Background Image 2-19 Procedure: Change the Network View Background Image 2-20 Procedure: Add a Node to the Current Session 2-21 2.6.3 Card View 2-21 2.7 CTC Navigation 2-22 2.8 Viewing CTC Table Data 2-24 2.9 Printing and Exporting CTC Data 2-26 Procedure: Print CTC Window and Table Data 2-27 Procedure: Export CTC Data 2-28 2.10 Displaying CTC Data in Other Applications 2-29 CHAPTER 3 Node
ページ8に含まれる内容の要旨
Contents 4.2 ONS 15454 IP Addressing Scenarios 4-2 4.2.1 Scenario 1: CTC and ONS 15454s on Same Subnet 4-2 4.2.2 Scenario 2: CTC and ONS 15454s Connected to Router 4-3 4.2.3 Scenario 3: Using Proxy ARP to Enable an ONS 15454 Gateway 4-4 4.2.4 Scenario 4: Default Gateway on CTC Computer 4-6 4.2.5 Scenario 5: Using Static Routes to Connect to LANs 4-6 Procedure: Create a Static Route 4-8 4.2.6 Scenario 6: Static Route for Multiple CTCs 4-9 4.2.7 Scenario 7: Using OSPF 4-10 Procedure: Set up OSPF
ページ9に含まれる内容の要旨
Contents Procedure: Add a UPSR Node 5-34 Procedure: Remove a UPSR Node 5-35 5.4 Subtending Rings 5-36 Procedure: Subtend a UPSR from a BLSR 5-38 Procedure: Subtend a BLSR from a UPSR 5-38 Procedure: Subtend a BLSR from a BLSR 5-40 5.5 Linear ADM Configurations 5-41 Procedure: Create a Linear ADM 5-42 Procedure: Convert a Linear ADM to UPSR 5-42 Procedure: Convert a Linear ADM to a BLSR 5-47 5.6 Path-Protected Mesh Networks 5-50 CHAPTER 6 Circuits and Tunnels 6-1 6.1 Circuits Overview 6-1 6.2 C
ページ10に含まれる内容の要旨
Contents 7.2.2 DS-3 Card Parameters 7-6 Procedure: Modify Line and Threshold Settings for the DS-3 Card 7-6 7.2.3 DS3E Card Parameters 7-8 Procedure: Modify Line and Threshold Settings for the DS3E Card 7-9 7.2.4 DS3XM-6 Card Parameters 7-11 Procedure: Modify Line and Threshold Settings for the DS3XM-6 Card 7-12 7.2.5 EC1-12 Card Parameters 7-14 Procedure: Modify Line and Threshold Settings for the EC-1 Card 7-14 7.3 Provisioning Optical Cards 7-18 7.3.1 Modifying Transmission Quality 7-18 Pro
ページ11に含まれる内容の要旨
Contents 8.1.5 Using the Baseline Button 8-7 Procedure: Use the Baseline Button on the Performance Monitoring Screen 8-7 8.1.6 Using the Clear Button 8-8 Procedure: Use the Clear Button on the Performance Monitoring Screen 8-8 8.2 Changing Thresholds 8-9 8.3 Enabling Intermediate-Path Performance Monitoring 8-10 8.4 Pointer Justification Count Parameters 8-12 Procedure: Enable Pointer Justification Count Performance Monitoring 8-13 8.5 Performance Monitoring for Electrical Cards 8-14 8.5.1 EC1
ページ12に含まれる内容の要旨
Contents 9.4.1 Q-Tagging (IEEE 802.1Q) 9-22 9.4.2 Priority Queuing (IEEE 802.1Q) 9-23 9.4.3 VLAN Membership 9-24 Procedure: Provision Ethernet Ports for VLAN Membership 9-24 9.5 Spanning Tree (IEEE 802.1D) 9-26 9.5.1 Multi-Instance Spanning Tree and VLANs 9-26 Procedure: Enable Spanning Tree on Ethernet Ports 9-26 9.5.2 Spanning Tree Parameters 9-27 9.5.3 Spanning Tree Configuration 9-27 9.5.4 Spanning Tree Map 9-28 Procedure: View the Spanning Tree Map 9-28 9.6 Ethernet Performance and Mainte
ページ13に含まれる内容の要旨
Contents 10.3.1.4 Row Display Options 10-11 10.3.2 Applying Alarm Profiles 10-11 Procedure: Apply an Alarm Profile at the Card View 10-13 Procedure: Apply an Alarm Profile at the Node View 10-13 10.4 Suppressing Alarms 10-14 Procedure: Suppressing Alarms 10-14 CHAPTER 11 SNMP 11-1 11.1 SNMP Overview 11-1 11.2 SNMP Basic Components 11-2 11.3 SNMP Support 11-3 Procedure: Set Up SNMP Support 11-3 11.4 SNMP Management Information Bases 11-5 11.5 SNMP Traps 11-6 11.6 SNMP Community Names 11-8 11.7
ページ14に含まれる内容の要旨
Contents Power Supply Disconnection Warning B-6 Outside Line Connection Warning B-7 Class 1 Laser Product Warning B-8 Class I and Class 1M Laser Warning B-8 Restricted Area Warning B-9 Ground Connection Warning B-10 Qualified Personnel Warning B-11 Invisible Laser Radiation Warning (other versions available) B-11 More Than One Power Supply B-12 Unterminated Fiber Warning B-13 Laser Activation Warning B-15 APPENDIX C Acronyms C-1 APPENDIX D Glossary D-1 INDEX Cisco ONS 15454 Installation and Op
ページ15に含まれる内容の要旨
F I GURES Figure 1-1 Cisco ONS 15454 dimensions 1-6 Figure 1-2 Reversing the mounting brackets (23-inch position to 19-inch position) 1-7 Figure 1-3 Mounting an ONS 15454 in a rack 1-8 Figure 1-4 A four-shelf node configuration 1-10 Figure 1-5 A four-shelf ONS 15454 Bay Assembly 1-11 Figure 1-6 The front-door erasable label 1-12 Figure 1-7 The laser warning on the front-door label 1-12 Figure 1-8 The ONS 15454 front door 1-13 Figure 1-9 Removing the ONS 15454 front door 1-14 Figure 1-10 Backpl
ページ16に含まれる内容の要旨
Figures Figure 1-32 Attaching a fiber boot 1-54 Figure 1-33 Managing cables on the front panel 1-55 Figure 1-34 Routing fiber-optic cables on the optical-card faceplate 1-56 Figure 1-35 Fold-down front door of the cable-management tray (displaying the cable routing channel) 1-57 Figure 1-36 Routing coaxial cable through the SMB EIA backplane 1-58 Figure 1-37 Clear BIC rear cover 1-59 Figure 1-38 Backplane attachment for BIC cover 1-60 Figure 1-39 Installing the BIC rear cover with spacers 1-60
ページ17に含まれる内容の要旨
Figures Figure 3-7 Editing protection groups 3-11 Figure 3-8 An ONS 15454 timing example 3-13 Figure 3-9 Setting Up ONS 15454 timing 3-16 Figure 3-10 Displaying ONS 15454 hardware information 3-18 Figure 4-1 Scenario 1: CTC and ONS 15454s on same subnet 4-3 Figure 4-2 Scenario 2: CTC and ONS 15454s connected to router 4-4 Figure 4-3 Scenario 3: Using Proxy ARP 4-5 Figure 4-4 Scenario 4: Default gateway on a CTC computer 4-6 Figure 4-5 Scenario 5: Static route with one CTC computer used as a de
ページ18に含まれる内容の要旨
Figures Figure 5-21 A UPSR with a fiber break 5-27 Figure 5-22 An OC-3 UPSR 5-28 Figure 5-23 Layout of Node ID 0 in the OC-3 UPSR example (Figure 5-15) 5-29 Figure 5-24 Layout of Node IDs 1 – 3 in the OC-3 UPSR example (Figure 5-15) 5-29 Figure 5-25 Connecting fiber to a four-node UPSR 5-31 Figure 5-26 Using the span shortcut menu to display circuits 5-33 Figure 5-27 Switching UPSR circuits 5-34 Figure 5-28 An ONS 15454 with multiple subtending rings 5-37 Figure 5-29 A UPSR subtending from a B
ページ19に含まれる内容の要旨
Figures Figure 6-16 Selecting DCC tunnel end points 6-23 Figure 7-1 Provisioning line parameters on the DS1-14 card 7-3 Figure 7-2 Provisioning thresholds for the OC48 IR 1310 card 7-19 Figure 7-3 IPPM provisioned for STS 1 on an OC-12 card 7-24 Figure 7-4 AIC alarm input and output 7-26 Figure 7-5 External alarms and controls using a virtual wire 7-27 Figure 7-6 Provisioning external alarms on the AIC card 7-28 Figure 7-7 Provisioning local orderwire 7-30 Figure 7-8 Viewing slot protection st
ページ20に含まれる内容の要旨
Figures Figure 9-4 A Single-card EtherSwitch configuration 9-5 Figure 9-5 A Multicard EtherSwitch point-to-point circuit 9-7 Figure 9-6 A Single-card Etherswitch point-to-point circuit 9-7 Figure 9-7 Provisioning an Ethernet circuit 9-8 Figure 9-8 Choosing a circuit source 9-8 Figure 9-9 A shared packet ring Ethernet circuit 9-10 Figure 9-10 Choosing a VLAN name and ID 9-11 Figure 9-11 Selecting VLANs 9-12 Figure 9-12 Adding a span 9-12 Figure 9-13 Viewing a span 9-13 Figure 9-14 A Hub and Spo
