ページ1に含まれる内容の要旨
INSTRUCTION MANUAL LIBRETTO D’ISTRUZIONI
IMPORTANT INFORMATION: Please read these instructions care- INFORMAZIONI IMPORTANTI: Leggere le istruzioni
GB IT
fully and make sure you understand them before using this unit. attentamente e capirle bene prima di usare l’utensile.
Retain these instructions for future reference. Conservare per ulteriore consultazione.
BETRIEBSANWEISUNG WICHTIGE INFORMATION: HASZNÁLATI ÚTMUTATÓ
Jótállást vállalni csak rendeltetésszerüen használatba vett
Lesen Sie diese Hi
ページ2に含まれる内容の要旨
7 A D E 3 17 15 1 1 14 11 717 21 10 20 16 12 5 9 13 4 8 3 2 Strokes engine totally Partner oil synthetic oil or McCulloch oil 2 23 50:1 40:1 2 18 2% 2,5% 22 19 6 3 3 1 ltr 20 cm 1 ltr 25 cm 5100 4100 10 200 5125 B 15 300 10 250 5 10 20 400 20 500 E3 E4 H F 1 I 11 11 11 2 A G C B 12 13 14 D L E
ページ3に含まれる内容の要旨
SUMMARY CHART TO IDENTIFY THE CORRECT GB E5 G H I1 GUARD NEEDED, WITH DIFFERENT CUTTING ATTACHMENTS DE ÜBERSICHTSTABELLE ZUR AUSWAHL DES RICHTI- GEN SCHUTZBLECHES FÜR DIE EINZELNEN SCHNEIDWERKZEUGE 43/46/49 cc 34/40 cc FR TABLEAU RECAPITULATIF POUR LE CORRECT 0,095” 197” ACCOUPLEMENT LAME OU TETE FIL NYLON / 2.4mm 5000mm 3.0mm A DEFENSE DE SECURITE 531025002 531025002 NL OVERZICHTSTABEL OM TE BEPALEN WELKE BESCHERMKAP GEBRUIKT MOET WORDEN BIJ DE E7 DIVERSE MAAI-ONDERDELEN 538248960 538248959
ページ4に含まれる内容の要旨
A. General description 1) ENGINE 2) SHAFT 3) THROTTLE TRIGGER 4) REAR CONTROL GRIP 5) BLADE 6) NYLON STRING HEAD 7) STOP SWITCH 8) CHOKE 9) STARTER HANDLE 10) HARNESS RING 11) SPARK PLUG 12) AIR FILTER COVER 13) FUEL TANK CAP 14) MUFFLER SHIELD Example of identification label 15) RIGHT CONTROL HANDLE 16) DELTA HANDLE LEGEND: 17) SAFETY LEVER 1) Guaranteed noise level according to directive 2000/14/EC 18) SAFETY POLE GUARD 2) Manufacturer's name and address 19) STRING CUTTER BLADE 3) Year of manu
ページ5に含まれる内容の要旨
Danger of kickback. The blade is Minimum safety distance 15m. capable of amputating arms and legs. CAUTION! Danger of serious leg Emergency stop. injuries. Take scrupulous care to fol- low the instructions in the manual. CAUTION! The cutting parts and muffler may get very hot and cause Maximum shaft speed. burns. Wait a w minutes before touching them. Use of the manual Inspect the machine carefully before every use, in 1 • Anyone who uses the machine should have read the case of violent impact o
ページ6に含まれる内容の要旨
plete, defective or has been altered by anyone other than During use an Authorized Service Center. The risk of accidents During use and for a few minutes after switching off 9 increases considerably if maintenance is not carried our the machine, the gearbox and zone near the shaft regularly in a professional way. In case of doubt contact an on which the cutting device is fastened are very hot. The authorized service center. muffler and its guard are very hot during use and after the engine has b
ページ7に含まれる内容の要旨
recommend emptying the fuel tank whenever you any excess pressure. After fueling, close the cap tightly. transport the machine. Take care not to spill any fuel. The fumes produced by the fuel can cause an explosion or fire. Gasoline is highly Fire prevention precautions inflammable: before going near any type of fuel, put out Never work with the brush cutter in the presence of your cigarette, pipe or cigar. Do not smoke or take 14 fire or spilled gasoline. If you have spilt it on yourself, sourc
ページ8に含まれる内容の要旨
nism. In case of emergency you need to be The harness is equipped with a fasten-release able to release the machine quickly. mechanism. The harness enables the operator to support the machine during use (see “Safety pre- cautions”, B7). D. Fuel Mixture Preparation of the mixture Filling the tank 7 14 15 14 15 Do not use any other type of fuel than the Clean the area around the fuel cap before remov- type recommended in this manual. This ing it, to prevent any impurities from contaminat- machine
ページ9に含まれる内容の要旨
and fasten it with the screw (E) (Make sure the Lower washer - e) Fixed mower gauge - f) Blade screws are tightened all the way (E) and are not locking screw (length mm 16). loosened by the vibrations. If necessary, tighten If you want to assemble the rotating mower them again). gauge, proceed as illustrated: a) Flange guard - b) Upper cap with blade centering - c) Blade with E4. Assembly/disassembly of line cutter head text and directional arrow facing upwards - d) Lower washer - e) Spacer - f)
ページ10に含まれる内容の要旨
G. Carburetor adjustment the cutting devices are moving, turn the screw (T) 8 9 10 11 gently counterclockwise until you obtain the prop- er adjustment. The correct minimum speed is Your machine can be equipped with a low emis- shown in the instruction manual in the paragraph sion carburetor. We recommend that you have of technical data. any adjustment of the carburetor made exclusive- ly by an authorized service center, which disposes of special equipment for ensuring the best per- All the above
ページ11に含まれる内容の要旨
I. Techniques for use pens, to bring out more string bump the head 1 4 5 6 7 8 9 against the ground: release the throttle trigger to reduce the engine speed to less than 8000 rpm. 10 11 12 13 14 16 Tap gently on the ground with the button (A) as Cutting techniques shown in the figure and the string will come out automatically. Accelerate again. If the string does During the cutting operations, keep the not come out make sure there is still some left engine running at high speed. After every and
ページ12に含まれる内容の要旨
M. Troubleshooting table Engine runs badly The machine Engine will or looses power runs but does not start when cutting not cut well Check STOP switch is in the posi- tion I. • Control fuel level min. 25%tank capacity. •• Check air filter is clean. •• Remove spark plug, dry it, clean it and adjust it, and replace it, if nec- •• essary. Change fuel filter. Contact your deal- • er. Carefully follow the cutting accesso- • ry assembly instructions. Check metal cutting accessory is sharp. Otherwise,
ページ13に含まれる内容の要旨
N. Declaration of conformity The undersigned, authorized by Husqvarna Outdoor Products Italia SpA, declares that the following products model /TYPE: BC060, starting from the serial numbers produced from 2006 on, manufac- tured by Husqvarna Outdoor Products Italia SpA, Valmadrera, Italia, comply with European Directive: 98/37/EEC (Machine Directive), 93/68/EEC (EEC Marking Directive) & 89/336/EEC (Electromagnetic Compatibility Directive), directive 2000/14/EEC (Enclosure V), 2002/88/EC gas emissi
