ページ1に含まれる内容の要旨
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
APEX
Safety Notice
POWER STATION
Hardware Identifier
TC-3502
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
TC-3502
Retain This
Manual for
Reference
06-23-08
OWNER'S
MANUAL
®
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
ページ2に含まれる内容の要旨
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 HARDWARE IDENTIFIER.....…....................................................................... 4 ASSEMBLY INSTRUCTIONS........................................................................... 5 EXPLODED DIAGRAM……………………………………………………………… 9 PARTS LIST..................
ページ3に含まれる内容の要旨
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person a
ページ4に含まれる内容の要旨
WARNING LABEL REPLACEMENT The warning label shown here has been placed on the Rear Base. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. 3
ページ5に含まれる内容の要旨
HARDWARE PACK 4
ページ6に含まれる内容の要旨
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Lower Vertical Frame (#2) to the Rear Base (#4). Secure it with two M10 x 3 ½” Carriage Bolts (#32), one U-shaped Bracket (#14), two Ø ¾” Washers (#35), and two M10 Aircraft Nuts (#33). B.) Attach the Right & Left Stabilizers (#5 & #6) to th
ページ7に含まれる内容の要旨
STEP-2 (See Diagram 2)
ページ8に含まれる内容の要旨
A.) Attach the Upper Vertical Frame (#1) onto the Lower Vertical Frame (#2). Secure it with two L-shaped Brackets (#9), two M10 x 3” Carriage Bolts (#31) from the front, two M10 x 3 5/8” Carriage Bolts (#30) from the side, four ∅ ¾” Washers (#35), and four M10 Aircraft Nuts (#33). B.) Attach the Chin-up Bar (#3) to the front of Upper Vertical Frame. Secure it with two M10 x 2” Allen Bolts (#25) and ∅ ¾” Washers (#35). Cover the Bolts with a 2” x 2 ¾” Plastic Cover (#16).
ページ9に含まれる内容の要旨
6 STEP 3 (See Diagram 3) A.) Attach the Left & Right Dip Supports (#7 & #8) to the Upper Vertical Frame (#1). Secure them to the Upper Vertical Frame with one M12 x 3 ¾” Allan Bolt (#26), two ∅ ¾” Washers (#37), and one M10 Aircraft Nut (#34). Do NOT over tighten the nut and bolt. Make sure the arms are able to move freely. B.) Secure the Left & Right Dip Supports together with one Four-hole Bracket (# 15) and four M8 x 3/8” Allen Bolts (#29). C.) Insert a Vertical Handle (#13) in
ページ10に含まれる内容の要旨
7 STEP 4 (See Diagram 4) A.) Attach the Backrest Pad (#12) to the Upper Vertical Frame (#1). Secure it with two M8 x 2 ¾” Allen Bolts (#28) and ∅ 5/8” Washers (#36). B.) Attach the Arm Pads (#11) to the Left & Right Dip Supports (#7 & #8). Secure each Arm Pad with two M8 x 2 ¾” Allen Bolts (#28) and Ø 5/8” Curved Washers (#39). C.) Insert a Foam Tube (#10) halfway through the holes on the Lower Vertical Frame (#2). Push two Foam Rolls (#24) onto the Tube from both ends. Plug two Foam
ページ11に含まれる内容の要旨
8 EXPLODED DIAGRAM
ページ12に含まれる内容の要旨
9
ページ13に含まれる内容の要旨
Parts list KEY NO. DESCRIPTION Q’ty 1 Upper Vertical Frame 1 2 Lower Vertical Frame 1 3 Chin-up Bar 1 4 Rear Base 1 5 Right Stabilizer 1 6 Left Stabilizer 1 7 Left Dip Support 1 8 Right Dip Support 1 9 L-shaped Bracket 2 10 Foam Tube 1 11 Arm Pad 2 12 Backrest Pad 1 13 Vertical Handle 2 14 U-shaped Bracket 1 15 Four-hole Bracket 1 16 2” x 2 ¾” Plastic Cover 1 17 Sleeve 2 18 Push-up Handle Grip 2 19 Chin-up Handle Grip 2 20 Dip Handle Grip 4 21 2” x 2 ¾” End Cap
ページ14に含まれる内容の要旨
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX
