ページ1に含まれる内容の要旨
MODEL W1778
18 GAUGE DEEP
STAPLER KIT
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#9569BL Printed in China
ページ2に含まれる内容の要旨
����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ����������������������������������������������������������������������� ��������������������������������������������������������������� � �������� �����������������������������������������������������
ページ3に含まれる内容の要旨
Model W1778 18 Gauge Deep Stapler Kit SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper
ページ4に含まれる内容の要旨
Model W1778 18 Gauge Deep Stapler Kit Safety Instructions for Pneumatic Tools 10. USE PROPER AIR HOSE for the 17. DISCONNECT TOOLS before tool. Make sure your air hose is in servicing, changing accessories, or good condition and is long enough moving to another location. to reach your work without 18. DO NOT OVERREACH. Keep proper stretching. footing/balance at all times. 11. WEAR PROPER APPAREL. Do 19. USE THE RECOMMENDED not wear loose clothing, gloves, ACCESSORIES. Consult owner’s ne
ページ5に含まれる内容の要旨
Model W1778 18 Gauge Deep Stapler Kit Additional Safety Instructions for Staplers 1. HAND INJURIES: Do not place 5. HOSE USAGE: Make sure your air your hands near the staple point hose is designed for the tool in of entry. A staple can deflect and use, is in good condition, and is tear through the surface of the long enough to reach your work workpiece, puncturing your hand or without stretching. However, an fingers. overly long air hose in the work area may be a tripping hazard. 2. COMBU
ページ6に含まれる内容の要旨
Model W1778 18 Gauge Deep Stapler Kit INTRODUCTION Woodstock Technical Tool Data Support Staple Size .......................... 18 Gauge 5 5 Staple Length ........................ ⁄8"-1 ⁄8" This tool has been specially designed 1 Staple Crown ............................... ⁄4" to provide many years of trouble-free Magazine Capacity ...............100 Staples service. Close attention to detail, Air Inlet .................................¼" NPT ruggedly built parts and a rigid quality Weight
ページ7に含まれる内容の要旨
Model W1778 18 Gauge Deep Stapler Kit Compressed Air System The Model W1778 is designed to be operated at 70-100 PSI using clean, dry, regulated, compressed air. Do not exceed the 120 PSI maximum operating pressure for your model. Before using your new stapler, regulate the air pressure to find the optimum setting within the specified operating range. Start by testing the stapler at a low setting, then increase the air Exceeding the maximum permissible pressure as needed for satisfacto
ページ8に含まれる内容の要旨
Model W1778 18 Gauge Deep Stapler Kit SETUP Unpacking This tool has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1778. Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the tool or examine the packaging materials care
ページ9に含まれる内容の要旨
Model W1778 18 Gauge Deep Stapler Kit — If the stapler fires when the trig- Safety Nose Mechanism ger is pulled, without the safety A safety mechanism on the nose of nose mechanism being depressed, the stapler protects against accidental then the stapler is not working firing. When the trigger is pressed, the properly. stapler will not fire until the safety nose mechanism is depressed. — If you find that the safety nose mechanism is not working prop- Before you use your stapler for the firs
ページ10に含まれる内容の要旨
Model W1778 18 Gauge Deep Stapler Kit OPERATIONS Loading When replacing staples in your Model W1778, follow these guidelines: Pusher Gauge: ........................................18 5 5 Length: ............................. ⁄8" – 1 ⁄8" Capacity: ................................... 100 1 Crown: ....................................... ⁄4" Magazine To load your stapler, do these steps: Figure 4. Loading staples into magazine. 1. DISCONNECT STAPLER FROM THE AIR Operating SUPPLY! If you have not
ページ11に含まれる内容の要旨
Model W1778 18 Gauge Deep Stapler Kit Single Fire Operation The stapler is designed to fire one staple DO NOT place your hands near the at a time. staple point of entry. A staple can deflect and tear through the surface To operate your stapler in single fire of the workpiece, puncturing your mode, do these steps: hand or fingers. 1. Depress the safety nose mechanism against the workpiece. Deflection is caused when grain irregularities, knots or foreign objects 2. Pull the trigger, th
ページ12に含まれる内容の要旨
Model W1778 18 Gauge Deep Stapler Kit 6. Secure the quick release latch. 4. Remove the cap. 7. Inspect the staple stick. If it is bent 5. The top of the piston should now be or damaged, throw it away and insert visible inside the cylinder, which is a new stick that only contains clean, housed in the head of the stapler. undamaged staples. DO NOT use dirty or damaged staples! 6. Open the nose cover as if to clear a jammed staple. 8. Slide the magazine forward until the catch lever engages. 7
ページ13に含まれる内容の要旨
Model W1778 18 Gauge Deep Stapler Kit CLEANING & LUBRICATION Cleaning Lubricating Disconnect the stapler from the air Standard pneumatic tool oil has been supply before cleaning. Use a good included with your new Shop Fox stapler solvent to clean the nose assembly of the to help maintain its useful life. Place two stapler. Always be sure that the stapler is to three drops of oil in the stapler air dry before using it again. inlet (as shown in Figure 7) before every use, or after 2 hours o
ページ14に含まれる内容の要旨
Model W1778 18 Gauge Deep Stapler Kit PARTS BREAKDOWN �� �� �� � �� � �� � �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� ��� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� � � � �� � � � � � � � � � � �� � � � � � -12-
ページ15に含まれる内容の要旨
Model W1778 18 Gauge Deep Stapler Kit PARTS LIST REF PART � # DESCRIPTION REF PART � # DESCRIPTION 1 XPLW01M LOCK � WASHER � 5MM 40 X1778040 NOSE �HEAD 2 X1778002 PISTON � REPAIR �KIT 41 X1778041 SAFETY �STAND �BRACKET 3 X1778003 CARRYING � CASE 42 X1778042 COMPRESSION � SPRING 4 XPAW04M HEX � WRENCH � 4MM 43 X1778043 SAFETY �STAND 5 XPAW03M HEX � WRENCH � 3MM 44 X1778044 ROLL � PIN�2.8 �X� 16 6 X1778006 AIR � PLUG � COVER 45 X1778045 SAFETY �SPACER 7 X1775007 1/4" � NPT � MALE �CONNECT 46 X177
ページ16に含まれる内容の要旨
Model W1778 18 Gauge Deep Stapler Kit Troubleshooting Symptom Possible Cause Solution Air leaking at 1. O-rings in trigger valve 1. O-rings must be replaced trigger valve area. housing are damaged. & operation of safety nose must be checked. Air leaking 1. Loose screws in housing. 1. Reseal and tighten screws. between housing 2. Damaged O-ring. 2. Replace O-ring and hose. 3. Loose air fitting. 3. Tighten air fitting & use teflon tape. Air leaking 1. Damaged seal. 1. Replace damaged seals. bet
ページ17に含まれる内容の要旨
WARRANTY AND RETURNS Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or reimbursement of third party expenses incurred. Woodstock International, Inc. will repair or replace, at its expense and at its option, the
ページ18に含まれる内容の要旨
ページ19に含まれる内容の要旨
Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email __________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ The following informa
ページ20に含まれる内容の要旨
FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 FOLD ALONG DOTTED LINE TAPE ALONG EDGES--PLEASE DO NOT STAPLE
