ページ1に含まれる内容の要旨
MODEL W1785
PALM NAILER
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#9629TS Printed in China
ページ2に含まれる内容の要旨
����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ����������������������������������������������������������������������� ��������������������������������������������������������������� � �������� �����������������������������������������������������
ページ3に含まれる内容の要旨
Model W1785 Palm Nailer SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prev
ページ4に含まれる内容の要旨
Model W1785 Palm Nailer Safety Instructions for Pneumatic Tools 10. USE PROPER AIR HOSE for the 17. DISCONNECT TOOLS before tool. Make sure your air hose is in servicing, changing accessories, or good condition and is long enough moving to another location. to reach your work without 18. DO NOT OVERREACH. Keep proper stretching. footing/balance at all times. 11. WEAR PROPER APPAREL. Do 19. USE THE RECOMMENDED not wear loose clothing, gloves, ACCESSORIES. Consult owner’s neckties, rings,
ページ5に含まれる内容の要旨
Model W1785 Palm Nailer Additional Safety for Nailers 1. HAND INJURIES: Do not place your 5. HOSE USAGE: Make sure your air hands near the nail point of entry. hose is designed for the tool in A nail can deflect and tear through use, is in good condition, and is the surface of the workpiece, long enough to reach your work puncturing your hand or fingers. without stretching. However, an overly long air hose in the work 2. COMBUSTIBLE GASES: Never area may be a tripping hazard. connect the
ページ6に含まれる内容の要旨
Model W1785 Palm Nailer INTRODUCTION Woodstock Technical Tool Data Support Nail Size ................................ 5d–70d Blows Per Minute ........................1000 This Model W1785 Palm Nailer has been Average Air Consumption ............. 5 CFM specially designed to provide many years Operating Air Pressure ...........70–100 PSI of trouble-free service. Close attention 1 Air Inlet Fitting ....................... ⁄4" NPT to detail, ruggedly built parts and a rigid Weight .............
ページ7に含まれる内容の要旨
Model W1785 Palm Nailer Compressed Air System The Model W1785 is designed to be operated at 70-100 PSI using clean, dry, regulated, compressed air. Do not exceed the 120 PSI maximum pressure for your model. Before using your nailer, regulate the air pressure to find the optimum setting within the specified operating range. Start by testing the nailer at a low setting, then increase the air pressure as Exceeding the maximum permissible needed for satisfactory results. operating pressure
ページ8に含まれる内容の要旨
Model W1785 Palm Nailer SETUP Unpacking This tool has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1785. Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the tool or examine the packaging materials carefully. Occasio
ページ9に含まれる内容の要旨
Model W1785 Palm Nailer OPERATIONS 3. Hold the nail firmly in place with one Operating hand as if using a regular hammer. If you have not read the safety instructions in this manual, do not 4. Place the tip of the palm nailer over operate the nailer. the end of the nail. When the ram pin touches the nail head, the nailer will Before you operate your nailer, place five automatically begin to hammer the to six drops of the included oil into the nail into the workpiece. quick connect fitting
ページ10に含まれる内容の要旨
Model W1785 Palm Nailer 5. Take hold of the ram pin and pull the Replacing Pistons/ piston from the cylinder. O-Rings 6. Place the new O-ring on the new Under heavy use, the piston or O-rings piston, and apply a thin film of tool may wear out. Replacement is quick and oil on the O-ring. easy. Contact your authorized Shop Fox dealer to obtain the Piston Repair Kit 7. Insert the new piston in the cylinder. (Part Number X1785127), or the Complete The new piston should easily slide O-Ring
ページ11に含まれる内容の要旨
Model W1785 Palm Nailer CLEANING & LUBRICATION Cleaning Lubricating Use a good solvent to clean the nose Standard pneumatic tool oil has been assembly of the nailer. Always be sure included with your new Shop Fox nailer that the nailer is dry before using it to help maintain its useful life. Place two again. to six drops of oil in the nailer air inlet (as shown in Figure 3) before every use, Do not allow dust, chips, sand, etc. or after 2 hours of continuous use. into the air connectors o
ページ12に含まれる内容の要旨
Model W1785 Palm Nailer PARTS BREAKDOWN & PARTS LIST ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� REF PART � # DESCRIPTION REF PART � # DESCRIPTION 101 XPSB15M CAP �SCREW � M5-.8 � X �20 115 X1785115 BUMPER � 16 � X �40 � X � 8 102 X1785102 CAP 116 X1785116 AXLE � SLEEVE � 8MM 103 X1785103 O-RING � 53.5 � X � 2.6 117 X1785117 HOUSING 104 X1785104 RUBBER �SEAL � 54MM 118 X1785118 AIR � INLET � PLUG � 1/4" � NPT 105 X178510
ページ13に含まれる内容の要旨
Model W1785 Palm Nailer TROUBLESHOOTING Symptom Possible Cause Possible Solution Air leaking at 1. O-rings in trigger valve 1. O-rings must be replaced trigger valve area. housing are damaged. & operation of safety nose must be checked. Air leaking between 1. Loose screws in housing. 1. Tighten screws. housing and hose 2. Damaged O-ring. 2. Replace O-ring 3. Loose air fitting. 3. Tighten air fitting & use teflon tape. Air leaking between 1. Damaged seal. 1. Replace damaged seals. housing and
ページ14に含まれる内容の要旨
WARRANTY AND RETURNS Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or reimbursement of third party expenses incurred. Woodstock International, Inc. will repair or replace, at its expense and at its option, the
ページ15に含まれる内容の要旨
Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email __________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ The following informa
ページ16に含まれる内容の要旨
FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 FOLD ALONG DOTTED LINE TAPE ALONG EDGES--PLEASE DO NOT STAPLE
